Beier Electronic

PAGE

SFR-1 sound drive controller from BEIER. Especially for trucks

1x SFR-1 sound speed controller from BEIER. Specially developed for trucks. 16 switching outputs for lighting. Can be set using the Sound Teacher SFR software. WITH CD-ROM/DVD or USB stick Speed controller for DC brush motor, sound module and light control module in one! Also suitable for bell-armature motors! Specially developed for trucks. Powerful BEC with 5,6V 3A. Optional load control, cruise control and brake function. Can be set in great detail using the -Sound Teacher SFR-. The speed controller is characterized by its high sensitivity. The controls are very realistic and dynamic and guarantee absolute driving fun. Thanks to a wide range of setting options, the speed controller can be easily and individually adapted to the most diverse model requirements and driving characteristics. All settings are made using the -Sound Teacher SFR- - the convenient configuration program from BEIER-Electronic. The model's lighting can be connected directly to the speed controller using the 16 light outputs. The speed controller has an extra output for connecting the IR transmitter diode for the light module SM-IR-16-2. (Article 9810). Features: - Supply voltage: 6-18V - Max. Motor current 30 A (continuous) 60 A (short-term) - PWM clock frequency 20 or 40 kHz - 16 switching outputs for the lighting - Powerful BEC 5,6 V 3 A - 6 proportional inputs (throttle, steering, control, sound, light) - 2 proportional outputs (servo outputs) - Failsafe in the event of reception interference (engine stop) - Start-up protection when switched on - Battery voltage monitoring - Temperature monitoring - Short-circuit protection for motor output stage - Short-circuit protection for BEC - Short-circuit protection switching outputs Can be selected via Sound Teacher SFR: - Load control on/off - Cruise control on/off - Braking function on/off - Handbrake function on/off - Selection of battery type: LiPo/ other type - Learning function (setup) for throttle channel on/off Can be set via Sound Teacher SFR (K-USB-2 required!):-Firmware update-Diagnosis-Channel inversion-Shutdown of undervoltage monitoring-Reduction of reversing speed-Selection of PWM clock frequency-Activation/setting of mass inertia-Activation/setting of steering inertia-Setting of handbrake hardness-Setting of throttle curve-Configuration of switching outputs (output type, brightness, xenon)-Configuration of light switch-Configuration of control channelThe speed controller is delivered with a standard configuration and is ready for use!-Battery connection 2x 1,5qmm, 25cm long, DEANS T-plug-Motor connection 2x 1,5qmm, 25cm long-2x servo cable for connection to receiver, 30cm long-Connection cable for loudspeaker, 25cm long-Cable for standby switch or volume potentiometer, 25cm-1x ribbon cable 40cm for connecting the switching outputs-Micro SD card (4GB) plus adapter-DVD with Sound-Teacher SFR-1 or USB stick (from 8/2024)-Manual SFR-1technical data:-Dimensions: 80 x 47 x 23 mm-Weight: 86g

Available immediately, delivery time: 1-4 days

Product number: 10974

€ 264,95 *

Subscriptions

Speakers 4 Ohm 50x50x22 mm

1x speaker 4 Ohm 50x50x25 mm. 88gr. Suitable for USM-RC-2, 10 watts, music output. Small design. LS-4R-10W-50 A suitable speaker housing: Article 9848 (not included).

Available immediately, delivery time: 1-4 days

Product number: 9847

€ 15,95 *

Subscriptions

Connection terminal AKL-8 BEIER-Electronic. Simple wire

Connection terminal for switching outputs For easy wiring of BEIER UFR-1230, SFR-1, UFR-1230D. AKL-8. Scope of delivery:10-pin connection terminal with spring contacts10-pin flat edge cable, color-coded, approx. 20cm long, with post couplings on both sidesOperating instructions

Available immediately, delivery time: 1-4 days

Product number: 10986

€ 13,95 *

Subscriptions

Data Cable K-USB 2

1x data cable K-USB-2. For live diagnosis, transfer of sound projects. Connection via USB interface. The data cable is NOT required. With the data cable K-USB-2, the sound modules SFR-1, SFR-1-D, USM-HL-2, light modules LM-xx, USM-RC-2 and USM-RC-3 as well as the speed controllers UFR-1230 /UFR-1230-D can be connected to a PC via a USB interface.The data cable has two functions:1. Live diagnosisWith the help of the data cable, the sound teacher can receive and display the current diagnostic data live (e.g. position of the proportional channels, status of the inputs and outputs, nautic values, etc.). This option is very helpful when troubleshooting.Note:The sound modules SFR-xx, USM-HL-2 and USM-RC-x can also save the diagnostic data on the SD card. This recorded data can be viewed without a data cable using the Sound Teacher's diagnostic function. However, the saved values have the disadvantage that you only see the "past" and not what is currently happening (live) on the module. 2. Transferring the configurations and sounds from the Sound Teacher/Drive Teacher to the SFR-x, USM-HL-2, USM-RC-x and UFR-1230/UFR-1230-D modules If a sound or a setting in the configuration is to be changed, the SD card must normally be unplugged from the module, plugged into the PC's card reader, the project data saved to the SD card using the Sound Teacher and the card plugged back into the sound module. However, if changes are made frequently, which occur particularly when the device is first put into operation or when testing new functions, unplugging and plugging can quickly become annoying. Using the data cable, all changes can be easily transferred to the sound module without having to keep re-plugging the SD card. However, transferring sounds using the data cable is relatively slow! A sound that is 10 seconds long takes around 60 seconds to transfer using the data cable. Therefore, transferring long sounds or large, new projects using the data cable is only advisable to a limited extent. The data cable is not absolutely necessary for setting up the sound module, but is often very helpful if you want to work a lot with the various setting options of the sound module.

Available immediately, delivery time: 1-4 days

Product number: 9822

€ 23,95 *

Subscriptions

SFR-1 sound drive controller from BEIER. Especially for trucks

SFR-1 Sound Speed Controller from BEIER. Specially developed for trucks. 16 switching outputs for lighting. Can be adjusted using the Sound-Teacher SFR software. No CD-ROM/DVD/USB stick required. Speed controller for DC brushed motors, sound module, and light control module in one! Also suitable for coreless motors! Specially developed for trucks. Powerful BEC with 5,6V 3A. Optional load control, cruise control, and braking functions. Can be adjusted in great detail using the Sound Teacher SFR. The speed controller is characterized by its high sensitivity. The control is very realistic and dynamic, guaranteeing absolute driving pleasure. Thanks to its diverse setting options, the speed controller can be easily and individually adapted to the most diverse model requirements and driving characteristics. All settings are made using the Sound-Teacher SFR – the convenient configuration program from BEIER Electronic. The model's lighting can be connected directly to the speed controller via the 16 light outputs. The speed controller has an extra output for connecting the IR transmitter diode for the SM-IR-16-2 light module (item 9810). Features: - Supply voltage: 6-18V - Max. Motor current 30 A (continuous) 60 A (short-term) - PWM clock frequency 20 or 40 kHz - 16 switching outputs for the lighting - Powerful BEC 5,6 V 3 A - 6 proportional inputs (throttle, steering, control, sound, light) - 2 proportional outputs (servo outputs) - Failsafe in case of reception interference (motor stop) - Start-up protection when switched on - Battery voltage monitoring - Temperature monitoring - Short-circuit protection for the motor output stage - Short-circuit protection for the BEC - Short-circuit protection for switching outputs. Selectable via Sound Teacher SFR: - Load control on/off - Cruise control on/off - Brake function on/off - Handbrake function on/off - Selection of battery type: LiPo/other type - Learning function (setup) for the throttle channel on/off. Adjustable via Sound Teacher SFR (K-USB-2) required!): -Firmware update -Diagnosis -Channel inversion -Shutdown of undervoltage monitoring -Reverse speed reduction -Selection of PWM clock frequency -Activation/adjustment of mass inertia -Activation/adjustment of steering inertia -Adjustment of handbrake hardness -Adjustment of throttle curve -Configuration of the switching outputs (output type, brightness, xenon) -Configuration of the light switch -Configuration of the control channel The speed controller is delivered with a standard configuration and is ready for use! -Battery connection 2x 1,5 mm², 25 cm long, DEANS T-connector -Motor connection 2x 1,5 mm², 25 cm long -2x servo cables for connection to receiver, 30 cm long -Connection cable for loudspeaker, 25 cm long -Cable for standby switch or volume potentiometer, 25 cm -1x ribbon cable 40 cm for connecting the switching outputs -Micro SD card (4 GB) plus adapter Data:-Dimensions: 80 x 47 x 23 mm-Weight: 86g

Available immediately, delivery time: 1-4 days

Product number: 10977

€ 254,95 *

Subscriptions

Volume potentiometer mini. BEIER electronic module. For setting

1x Mini volume potentiometer. BEIER Electronic Module. For adjusting the volume. Wire length: 20 cm. Resistance: 100 kOhm. For SFR-1, USM-RC-2, USM-RC, and USM-xx. Mini version.

Ready to ship in 5 days, delivery time 1-4 days

Product number: 11798

€ 6,95 *

Subscriptions

Volume potentiometer

1x volume potentiometer. For BEIER electronic modules. To adjust the volume. Wire length: 20cm. Resistance 100 kOhm. For SFR-1, USM-RC-2, USM-RC-3, USM-xx.

End of life - article no longer available!

Product number: 9813

€ 4,95 *

Subscriptions

Details

Infrared transmitting diode

1x Infrared Transmitting diode for BEIER system

Available immediately, delivery time: 1-4 days

Product number: 9845

€ 3,55 *

Subscriptions

Speaker case for LS-4R 10W-50

1x speaker housing for LS-4R-10W-50 Dimensions: 50x50x24 mm. Suitable for speaker with article number: 9847 (not included). Hole spacing 43mm.

Available immediately, delivery time: 1-4 days

Product number: 9848

€ 10,95 *

Subscriptions

Ribbon cable 10-pin for BEIER sound module USM-RC-2, 1m

1x 10-pin ribbon cable for BEIER sound module USM-RC-2, USM-RC-3, as well as sound controllers of the SFR series, controllers of the UFR series, light modules LM-BT-16-4, LM-IR-16-4. Length: 100cm.

Available immediately, delivery time: 1-4 days

Product number: 10975

€ 3,25 *

Subscriptions

Connection terminal BEIER AKL-8-W. For switching outputs to the einf

Connection terminal for switching outputs For easy wiring of BEIER UFR-1230, UFR-1230D, SFR-1. AKL-8-W connection terminal with slot for 8 series resistors. With 20cm flat cable

Available immediately, delivery time: 1-4 days

Product number: 10987

€ 18,94 * € 18,95 * (0.05% saved)

Subscriptions

MFR-1210 mini speed controller from BEIER. Especially for Nebenant

1x MFR-1210 mini speed controller from BEIER. Especially for auxiliary and auxiliary drives. Mini speed controller for DC brush motorsEspecially for auxiliary and auxiliary drives and for the complete speed control of small modelsSupply voltage: 6 - 16 V DCMax. Motor current: 10 ABEC with 5,0 V and 0,5 A (max. 1 A)PWM clock frequency 20 kHzJerk-free EMF motor brakeSmooth polarity reversal by monitoring the motor speedAcoustic warning signal in the event of overtemperature, overcurrent and reception interferenceSmall size: 26 x 19 x 6 mmThe mini speed controller MFR-1210 is a small and versatile speed controller for brush motors up to 10 A. It controls forward and reverse travel continuously and sensitively and includes a BEC with 5 V.With a PWM clock frequency of 20 kHz, no annoying whistling noises are audible.The MFR-1210 is suitable for use in functional model making, in particular for auxiliary and auxiliary drives, but also for the complete drive of small models.Due to the small dimensions and the simple connection, movements of e.g. trailer supports and lifting arms, or tipping functions and the Turret rotation on tanks is easy to implement and control. As soon as the throttle is stopped and the throttle channel is in neutral (middle position), the speed controller actively brakes with the EMK motor brake until the model comes to a standstill (with a braking ramp). The motor speed is continuously monitored to ensure gentle operation of the motor and battery. This is particularly important when changing between forward and reverse travel. Before reversing the polarity, the motor is braked to a standstill and only then accelerated in the other direction. The speed controller does not require any additional programming of the transmitter. The zero point range (middle position) of the throttle channel is 1,500 ms, suitable for almost all remote controls. The mini speed controller uses acoustic signals to warn of overheating, overcurrent and missing signal from the receiver. In order to equip the motor movements with the appropriate sound and to control the speed of the motors, the speed controller can be connected to the servo outputs of the following BEIER modules: -Sound module USM-RC-2 -Light module SM-IR-16-2 -Extension module EXM-2

Available immediately, delivery time: 1-4 days

Product number: 10851

€ 32,95 *

Subscriptions

Speaker cable approx. 20cm for Beier modules

1x speaker cable. For connecting speakers. Suitable for BEIER sound module USM-RC-2/3. Length: 20 cm. Plug color: white.

Available immediately, delivery time: 1-4 days

Product number: 9814

€ 1,30 *

Subscriptions

Standby switch for SFR-1

Standby switch for the SFR-1. With soldered cable (approx. 25cm long). For connection to contact point X9 of the SFR-1. When the standby switch is closed, the BEC voltage of the SFR-1 is switched off and the sound-controlled speed controller goes into "standby" mode. The module's current draw then drops to only about 1 mA. This allows the model to remain in "standby" mode for several hours without noticeably draining the battery. However, if the model is not used for an extended period (several days), the battery should still be completely disconnected. The standby switch is supplied with a soldered cable. The cable length is approximately 25 cm.

Available immediately, delivery time: 1-4 days

Product number: 11677

€ 5,25 *

Subscriptions

Infrared light module LM-IR-16-4 for the BEIER modules

1x infrared light module LM-IR-16-4 for the BEIER modules USM-RC-2 and -RC-3, SFR-1 for controlling lights on the trailer. Also compatible with UFR-1230. This module is required in the trailer!Description:With this additional module, the lighting on a truck trailer can be controlled with numerous light effects as well as movements (servos and motors).The (light) signals are transmitted wirelessly via an infrared diode. A connection cable between the truck and trailer is therefore not necessary. However, a separate battery must be installed in the trailer for the supply voltage.This module is suitable for expanding the Beier modules SFR-1, USM-RC-2, USM-RC-3 and UFR-1230.Light functions:The LM-IR-16-4 has 16 switching outputs for e.g. lamps and LEDs. 12 of the 16 outputs are a copy of the 12 switching outputs of the USM-RC-2. Various functions are available for the remaining 4 outputs, such as a 1- and 4-channel rotating light, a 4- and 8-channel running light and various flashers. -Motor control:The motor output on this light module can be used to directly control e.g. support motors, ramps or tilt functions. A switch for manual control of the motor output can also be optionally connected to the module.Movement functions:In addition to the 16 switching outputs, there are also 4 servo outputs with which various movements can be controlled. Possible applications for this include the movement of trailer supports, locking and unlocking a saddle support, tilting a tipper and many other movements.In order to control additional motors, speed controllers can also be connected to these servo outputs.Another IR transmitter diode can be connected to the light module, which forwards the received IR signal 1:1 to another light module.Technical data:-Voltage: 6-12V DC-Current consumption:25mA Quiescent current switching outputs: 16-Servo outputs: 4-1 Motor output: max. 2A-Dimensions: 58x44x17 mm-Weight: 26gMany settings can be changed using the LM-Teacher software.Both the IR transmitter and the IR receiver diode are included in the scope of delivery of this module!These infrared diodes are also available individually:IR transmitter diode: Article 9845IR receiver diode: Article 9844Interference suppression is particularly important if trailer supports are also controlled! In this case, a ferrite ring should be used on the receiving diode as well as on the motor cable of the supports. Ferrite ring 11770 is recommended.

Ready to ship in 5 days, delivery time 1-4 days

Product number: 12261

€ 89,95 *

Subscriptions

Beier switching module RC-SM-4. 4 outputs with max.4A each

1x switching module RC-SM-4 (new 2020). 4 outputs with a maximum output current of 4A each to be connected directly to the receiver. Switching current up to 4A each. (10A total current) The RC switching module RC-SM-4 has 4 outputs that can be switched via a proportional channel of an RC remote control. The RC-SM-4 is connected directly to an output of the remote control receiver via a servo cable. It is also possible to connect the switching module in parallel (e.g. with a Y-cable) to an existing servo or speed controller. 4 different consumers can be switched on/off independently of one another via the 4 outputs. Many applications are possible in which consumers need to be switched (e.g. lamps, LEDs, small motors, relays, etc.). The outputs are designed to be minus-switching. The module can be operated in 15 different modes. The setting is made using the remote control. The necessary steps are explained in simple terms in the extensive documentation. The module is supplied with a servo cable with a Graupner plug that is approx. 30 cm long. The connections for the 4 outputs are made as cable strands. Technical data: Required RC proportional channel: 1 Supply voltage: 4,0 - 8,0V (via RC receiver) Own current consumption: approx. 10 - 25 mASwitching outputs: 4 pieces, negative switching Switching voltage: max. 20V DC Switching current (per output): max. 4ATotal current: max. 10A! Switching variants: Various button functions Various switching functions (memory switch) Switching of various light effects Setting of up to 7 different running speeds Zero point of the RC signal: fixed at 1,5ms Switching modes: 15, freely selectable Dimensions: 20 x 15 x 4mmWeight: 12 gr.

Available immediately, delivery time: 1-4 days

Product number: 11991

€ 26,95 *

Subscriptions

Terminal for switching outputs

1x terminal for switching outputs For easy wiring of BEIER USM-RC-2 and 2 EXM.

Available immediately, delivery time: 1-4 days

Product number: 9821

€ 13,95 *

Subscriptions

Beier sound module USM-RC-3 WITH stick. Individually programmed

1x Beier sound module USM-RC-3 WITH USB stick. Individually programmable sound, light and movement module. Over 140 finished sound projects. Delivered with USB stick and instructions. The sound module was specially developed for RC model building to create authentic and speed-dependent sounds, extensive lighting options, and additional servo movements. Features: Individually programmable sound, light, and movement module Over 140 ready-made sound projects with preset and customizable sounds and noises Use of your own noises, sounds, and songs possible Speed-dependent motor and movement sounds Optimal sound thanks to a powerful amplifier NF amplifier: 20W 16 outputs for switching LEDs, lamps, relays, etc. Freely adjustable light sequences, e.g. for an all-round light4 programmable servo outputsEasy updating of the sound teacher and firmware Easy transfer of all settings via micro SD cardThe USM-RC-3 sound module is characterized by its high adaptability. All settings are saved on a micro SD card and can therefore be easily changed. All you need is a reader and the "Sound Teacher" software. There are 3 different operating modes: - Digital operation (connection to the receiver) The connection is made using a servo patch cable directly to the receiver and parallel to the speed controller. - Analogue operation (connection directly to the motor) - Mixed operation (combination of digital and analogue operation) These modes are used for speed controllers with special functions, such as cruise control. The model's speed is measured directly from the motor. The functions can be controlled in various ways. The remote control assignments are made via the sound teacher. Sound functions: Driving and engine sounds for the engine (speed-dependent) Additional sounds (horns, hydraulic and compressed air noises, etc.) Random sounds (chain squealing, animal and ambient noises) Detailed: Starting noises (cold/warm start) Parking noises Starting noises Stopping noises Idle noises Braking noises Reversing noises Only one speaker needs to be connected to the sound module. (4 Ohm/8 Watt is recommended.)Light functions:The sound module offers 16 switching outputs. The individual outputs can be configured in the Sound Teacher. This allows functions such as Frequent flashing, flickering, or on/off is possible. Movement functions: The USM-RC-3 sound module also offers 4 outputs for connecting servos. Technical data: Supply voltage: 5-15V DC Quiescent current: approx. 80mA Operating current: depends on volume and switched load Switching inputs: 4 Switching outputs: 16 Proportional inputs: 8 Proportional outputs: 4 Servo outputs Recommended speakers: 4-8 ohms Volume adjustment: via external potentiometer or remote control Supported sound data: WAV format 8/16 bit mono/stereo, 22/44kHz Sound output: 16 bit, mono, 44kHz Weight: 25g Dimensions: 65x43x17 mm Scope of delivery: Sound module USM-RC-3 Micro SD card (32GB) + adapter (item 9818) 1 connection cable for speaker (25cm) (item 9814) 2 servo patch cables (30cm) for connecting to a receiver, item 9812 1 ribbon cable (40cm) for connecting the switching outputs (item 9815 1x Fuse holder + 4A fuse (item 9817) USB stick with software (Sound-Teacher USM-RC-3) and sounds Operating instructions (manual, German) Sounds are available for the following vehicles: Car - Ford F-350 (V8) Car - Land Rover Discovery TD Car - Mercedes 320 CDI_1 Car - Mercedes 320 CDI_2 Car - Mercedes C63 AMG Car - Mercedes G (Diesel) Car - Mercedes Sprinter Car - V8 Car - VW Bus Car - VW Golf GTI Car - VW Beetle Excavator - Liebherr Excavator - Volvo Aircraft - Focke Wulf 190 Aircraft - Me 109 G10 Aircraft - Wright Radial Engine Helicopter - Huey Helicopter - Rescue Helicopter Dump Truck - Volvo A25C Crawler Loader - Caterpillar Locomotive - Climax Locomotive - Steam locomotive - Steam locomotive_1 - Diesel locomotive - Electric locomotive - GP38 motorcycle - Harley Davidson tank - Elefant tank - Gepard tank - Gepard_1 tank - Jagdpanther tank - Jagdpanther_1 tank - KV-1 tank - Kanonenjagdpanzer tank - King Tiger tank - King Tiger_1 tank - Leopard 1 tank - Leopard 1_1 tank - Leopard 2 tank - Leopard 2A6 tank - M1 tank - M26 tank - M41 Walker Bulldog tank - MARS tank - Panther tank - Panther G tank - Panther G_1 tank - Panther_1 tank - Panzer III tank - Panzer III_1 tank - Panzer IV tank - Piranha IIIH tank - Sd.Kfz. 7-Tank - Sherman Tank - T-34 Tank - T-55 Tank - Tiger Tank - Tiger_1 Tank - Tiger_2 Tank - Tiger_3 Snowcat - PB300 Snowcat - PB600 Snowcat - PB600_2 Snowcat - Prinoth Beast Wheel Loader - Liebherr Wheel Loader - Liebherr L586 Crawler - DET250 Crawler - Liebherr PR734 Crawler - T100 Ship - Barge Ship - Steamship Ship - Steamship SS Fury ship - Icebreaker Kontio ship - Fireboat ship - Freighter ship - Cutter ship - Cutter_1 ship - Mississippi steamboat ship - Mississippi steamboat_1 ship - Patrol boat Hohwacht II ship - Police boat ship - Powerboat Mercruiser ship - Riva Aquarama ship - Riva Ariston ship - Marine diesel ship - Marine diesel_1 ship - Battleship Bismarck ship - Tugboat ship - Tug_1 ship - Tug_2 ship - Tug_3 ship - Tug_4 ship - Tug_5 ship - Tug_6 ship - Sea rescue cruiser ship - Torpedo boat T56 ship - Yacht V12 tractor - Caterpillar 830m tractor - Claas Xerion tractor - Eicher Mammut tractor - Fendt Dieselross tractor - Fendt Vario 936 tractor - JCB Fastrac tractor - John Deere 8245R tractor - John Deere 8530 tractor - Kirovets K-700 tractor - Kirovets K-700A tractor - Lanz tractor - Lanz Bulldog tractor - MB-Trac tractor - MB-Trac 1100 tractor - MB-Trac 1800 tractor - Schlüter 1250VL tractor - Schlüter Compact 950 tractor - Schlüter Super 1500 TVL tractor - Unknown 01 truck - DAF XF 105 truck - Detroit Diesel truck - GAZ-66 truck - IVECO 140 E 30 truck - KRAZ 255-Truck - Kenworth W900-Truck - M35A2-Truck - MAN-Truck - MB Actros 2013-Truck - MB-NG-Truck - MB-SK 88-Truck - Mack-Truck - Scania 140 V8-Truck - Scania V8-Truck - Scania V8 with turbo whistle-Truck - Scania V8_1-Truck - Scania Vabis 56-Truck - Unimog 1600-Truck - Unimog 400-Truck - Unimog 406-Truck - Unimog 406_1-Truck - Ural-Truck - Volvo FH16-Turbine - 1-U-Boat - U96. The list is constantly being expanded.

Available immediately, delivery time: 1-4 days

Product number: 12333

€ 189,95 *

Subscriptions

Ribbon cable 10 poli for USM-RC-2

1x 10-pin ribbon cable for BEIER sound module USM-RC-2, USM-RC-3, sound speed controller of the SFR series, light modules LM-BT-16-4, LM-IR-16-4. Length: 40cm.

Available immediately, delivery time: 1-4 days

Product number: 9815

€ 2,25 *

Subscriptions

BEIER-Electronic Multiswitch Converter MSC-8-C-LCD

BEIER Electronic Multiswitch Converter MSC-8-C-LCD. With the multiswitch converters MSC 8-C-LCD, the signals from 8 switches of the CARSON Reflex Stick MULTI PRO LCD 14 channel can be combined and transmitted collectively.The Reflex Stick MULTI PRO LCD 14 channel from CARSON-MODEL Sport is an inexpensive but fully equipped and technically high-quality 14-channel remote control system for universal use in many RC vehicles and ships. The MSC are plugged directly onto the receiver of the CARSON Reflex Stick MULTI PRO LCD 14 channel and transmit the states of 8 switches of the remote control via only one proportional channel to the sound module USM-RC-2, USM-RC-3, SFR-1 or to the UFR-1230 of the UFR series.In this way, 8 switches can be used to control various functions of the sound module or the speed controller.Technical details: MSC -8-C-LCDEvaluates 8 switchesChannels 5, 6 and 9 - 14 are connected to the receiver via the MSC-8-C-LCD occupiedChannels 1 - 4, 7 and 8 of the receiver remain free.All MSCs have dimensions (without receiver) of: 24 x 32 x 12 mm.Scope of delivery:Multiswitch converter moduleServo patch cable (30 cm )Instruction manual (German)Attention: Remote control and receiver are not included in delivery!The MSC modules work with these items:Sound speed controller SFR-1Double sound speed controller SFR-1-Double sound speed controller SFR-1-HLSound module USM-RC-2Sound module USM -RC-3Speed controller UFR-1230Dual speed controller UFR-1230-D

Available immediately, delivery time: 1-4 days

Product number: 10517

€ 44,95 *

Subscriptions

Ferrite ring 16mm diameter, material T38

1 ferrite ring. Material T38. Outside: 16mm. Inside: 9,6mm. Thickness: 6,3mm. Weight: 4gr. Ferrite ring for suppression of motor and receiver lines.

Available immediately, delivery time: 1-4 days

Product number: 11770

€ 2,20 *

Subscriptions

Y-cable with fuse holder

1x Y-cable with fuse holder for connecting to the battery and speed controller. With TAM connector and fuse (4A). For Beier sound module. Tamiya on both sides.

Available immediately, delivery time: 1-4 days

Product number: 9816

€ 11,95 *

Subscriptions

Bluetooth light module LM-BT-16-4 for the BEIER modules

1x Bluetooth light module LM-BT-16-4 for the BEIER modules USM-RC-3, SFR-1 for controlling lights on the semi-trailer. This module is required in the semi-trailer!Description:With this additional module, both the lighting, with numerous light effects, and movements (servos and motors) on a truck trailer can be controlled.The (light) signals are transmitted wirelessly via a Bluetooth connection. A connection cable between the truck and the trailer is therefore not necessary. However, a separate battery must be installed in the trailer for the supply voltage.This module is for expanding the Beier modules SFR-1 and USM-RC-2. Light functions:The LM-BT-16-4 has 16 switching outputs for lamps and LEDs, for example. 12 of the 16 outputs are a copy of the 12 switching outputs of the USM-RC-2/SFR-1. Various functions are available for the remaining 4 outputs, such as a 1- and 4-channel rotating light, a 4- and 8-channel running light and various flashers. -Motor control:The motor output on this light module can be used to directly control e.g. support motors, ramps or tilt functions. A switch for manual control of the motor output can also be optionally connected to the module.Movement functions:In addition to the 16 switching outputs, there are also 4 servo outputs with which various movements can be controlled. Possible applications for this include the movement of trailer supports, locking and unlocking a saddle support, tilting a tipper and many other movements. To control additional motors, speed controllers can also be connected to these servo outputs. Another Bluetooth transmitter can be connected to the light module, which forwards the received signal 1:1 to another light module. Technical specifications: - Voltage: 6-12V DC - Current consumption: 25mA Quiescent current switching outputs: 16 - Servo outputs: 4-1 Motor output: max. 2A - Dimensions: 58x44x17 mm - Weight: 26g Many settings can be changed using the LM-Teacher software. This module comes with 1x the BT transmitter. This Bluetooth transmitter is also available individually: Bluetooth transmitter: Article 12263 Interference suppression is particularly important if trailer supports are also controlled! A ferrite ring should be used on the receiving diode as well as on the motor cable of the supports. The ferrite ring 11770 is recommended.

Available immediately, delivery time: 1-4 days

Product number: 12262

€ 109,94 * € 109,95 * (0.01% saved)

Subscriptions

Fuseholders 4A fuse

1x fuse holder 4A fuse to protect the Sound Module with a short circuit, Length: 30 cm. For BEIER-Electronic sound module.

Available immediately, delivery time: 1-4 days

Product number: 9817

€ 3,25 *

Subscriptions

Tip:

UFR 1230 speed controller of BEIER-Electronic

1x UFR-1230 speed controller from BEIER. Specially developed for trucks. 8 switching outputs for lighting. Adjustable via the Drive-Teacher software. DVD not included. Speed controller for DC brushed motors. Specially developed for vehicles/trucks. Powerful BEC with 5,2V 3A. Optional load control, cruise control, and braking functions. Highly adjustable via the "Drive Teacher." The speed controller is characterized by its high sensitivity. The control is very realistic and dynamic, guaranteeing absolute driving pleasure. Thanks to its diverse setting options, the speed controller can be easily and individually adapted to the most diverse model requirements and driving characteristics. The settings are made via a DIP switch or with the help of the "Drive Teacher." The model's lighting can be connected directly to the speed controller via the 8 light outputs. The speed controller has an extra output for connecting the IR transmitter diode for the light module SM-IR-16-2.Features:-Supply voltage: 6-18V-Max. Motor current 30 A (continuous) 60 A (short-term) - PWM clock frequency 20 or 40 kHz - 8 switching outputs for the lighting - Powerful BEC 5,2 V 3 A - 3 proportional inputs (throttle, steering, control) - 2 proportional outputs (sound module, steering servo) - Mailsafe in case of reception interference (motor stop) - Start-up protection when switched on - Battery voltage monitoring - Temperature monitoring - Short-circuit protection for the motor output stage. Selectable via DIP switch: - Load control on/off - Cruise control on/off - Brake function on/off - Handbrake function on/off - Selection of battery type: LiPo/other type - Learning function (setup) for throttle channel on/off. Adjustable via Drive Teacher (K-USB-2 required!): - Firmware update - Diagnostics - Channel inversion - Switch-off undervoltage monitoring - Reduction of reversing speed - Selection of PWM clock frequency activation/inertia setting/steering inertia setting; handbrake hardness setting; throttle curve setting; switching output configuration (output type, brightness, xenon); light switch configuration; control channel configuration. The speed controller is delivered with a standard configuration and is ready for use! Technical specifications: Dimensions: 65 x 45 x 23 mm; Weight: 75g

Available immediately, delivery time: 1-4 days

Product number: 9905

€ 149,95 *

Subscriptions

Bluetooth module BTC-1. For the SFR-1 by Beier

1x Bluetooth module BTC-1. For the SFR-1 and SFR-1-D from Beier. With the BTC-1, the SFR-1 (from firmware 1.20) can be controlled via Bluetooth using the Android app. A small gadget for the Beier sound speed controller SFR-1 and SFR-1-D. With the Bluetooth module BTC-1, the sound speed controller SFR-1 (from firmware V1.20) can be controlled via Bluetooth using the Android app "SFR-1 Controller". The same applies to the double sound speed controller SFR-1-D. Due to the low transmission power of smartphones and tablets, the range is only max. 10 - 30 meters! Control via Bluetooth is therefore only suitable for models that do not exceed this distance from the transmitter! The model can be driven via the app (throttle and steering) and all available functions (additional sounds, WAV player, lights, servos, etc.) of the SFR-1xx can be controlled. Parallel operation of the standard RC transmitter and Bluetooth control is also possible.

Available immediately, delivery time: 1-4 days

Product number: 11685

€ 21,96 *

Subscriptions

Beier sound module USM-RC-3 WITHOUT DVD / manual. Individual p

1x Beier sound module USM-RC-3 WITHOUT DVD. Individually programmable sound, light and movement module. Over 140 finished sound projects. Delivery without USB stick/instructions. The sound module was specially developed for RC model building to create authentic and speed-dependent sounds, extensive lighting options, and additional servo movements. Features: Individually programmable sound, light, and movement module Over 140 ready-made sound projects with preset and customizable sounds and noises Use of your own noises, sounds, and songs possible Speed-dependent motor and movement sounds Optimal sound thanks to a powerful amplifier NF amplifier: 20W 16 outputs for switching LEDs, lamps, relays, etc. Freely adjustable light sequences, e.g. for an all-round light4 programmable servo outputsEasy updating of the sound teacher and firmware Easy transfer of all settings via micro SD cardThe USM-RC-3 sound module is characterized by its high adaptability. All settings are saved on a micro SD card and can therefore be easily changed. All you need is a reader and the Sound Teacher software. There are three different operating modes: - Digital mode (connected to the receiver). The connection is made via a servo patch cable directly to the receiver and parallel to the speed controller. - Analog mode (connected directly to the motor). - Mixed mode (combination of digital and analog mode). These modes are used for speed controllers with special functions, such as cruise control. The model's speed is measured directly from the motor. The functions can be controlled in various ways. The remote control assignments are made via the sound teacher. Sound functions: Driving and engine sounds for the engine (speed-dependent) Additional sounds (horns, hydraulic and compressed air noises, etc.) Random sounds (chain squealing, animal and ambient noises) Detailed: Starting noises (cold/warm start) Parking noises Starting noises Stopping noises Idle noises Braking noises Reversing noises Only one speaker needs to be connected to the sound module. (4 Ohm/8 Watt is recommended.)Light functions:The sound module offers 16 switching outputs. The individual outputs can be configured in the Sound Teacher. This allows functions such as Frequent flashing, flickering, or on/off is possible. Movement functions: The USM-RC-3 sound module also offers 4 outputs for connecting servos. Technical data: Supply voltage: 5-15V DC Quiescent current: approx. 80mA Operating current: depends on volume and switched load Switching inputs: 4 Switching outputs: 16 Proportional inputs: 8 Proportional outputs: 4 Servo outputs Recommended speakers: 4-8 ohms Volume adjustment: via external potentiometer or remote control Supported sound data: WAV format 8/16 bit mono/stereo, 22/44kHz Sound output: 16 bit, mono, 44kHz Weight: 25g Dimensions: 65x43x17 mm Scope of delivery: Sound module USM-RC-3 Micro SD card (32GB) + adapter (item 9818) 1 connection cable for speaker (25cm) (item 9814) 2 servo patch cables (30cm) for connecting to a receiver, item 98121 40 ribbon cable (98151cm) for connecting the switching outputs (item 4x Fuse holder + 9817A fuse (item 350) Sounds are available for the following vehicles: Car - Ford F-8 (V320) Car - Land Rover Discovery TD Car - Mercedes 1 CDI_320 Car - Mercedes 2 CDI_63 Car - Mercedes C8 AMG Car - Mercedes G (Diesel) Car - Mercedes Sprinter Car - V190 Car - VW Bus Car - VW Golf GTI Car - VW Beetle Excavator - Liebherr Excavator - Volvo Airplane - Focke Wulf 109 Airplane - Me 10 G25 Airplane - Wright Radial Engine Helicopter - Huey Helicopter - Rescue Helicopter Dump Truck - Volvo A1C Crawler Loader - Caterpillar Locomotive - Climax Locomotive - Steam Locomotive - Steam Locomotive_38 Locomotive - Diesel Locomotive - Electric Locomotive - GP1 motorcycle - Harley Davidson tank - Elefant tank - Gepard tank - Gepard_1 tank - Jagdpanther tank - Jagdpanther_1 tank - KV-1 tank - Kanonenjagdpanzer tank - King Tiger tank - King Tiger_1 tank - Leopard 1 tank - Leopard 1_2 tank - Leopard 2 tank - Leopard 6A1 tank - M26 tank - M41 tank - M1 Walker Bulldog tank - MARS tank - Panther tank - Panther G tank - Panther G_1 tank - Panther_1 tank - Panzer III tank - Panzer III_XNUMX tank - Panzer IV tank - Piranha IIIH tank - Sd.Kfz. 7-Tank - Sherman Tank - T-34 Tank - T-55 Tank - Tiger Tank - Tiger_1 Tank - Tiger_2 Tank - Tiger_3 Snowcat - PB300 Snowcat - PB600 Snowcat - PB600_2 Snowcat - Prinoth Beast Wheel Loader - Liebherr Wheel Loader - Liebherr L586 Crawler - DET250 Crawler - Liebherr PR734 Crawler - T100 Ship - Barge Ship - Steamship Ship - Steamship SS Fury ship - Icebreaker Kontio ship - Fireboat ship - Freighter ship - Cutter ship - Cutter_1 ship - Mississippi steamboat ship - Mississippi steamboat_1 ship - Patrol boat Hohwacht II ship - Police boat ship - Powerboat Mercruiser ship - Riva Aquarama ship - Riva Ariston ship - Marine diesel ship - Marine diesel_1 ship - Battleship Bismarck ship - Tugboat ship - Tug_1 ship - Tug_2 ship - Tug_3 ship - Tug_4 ship - Tug_5 ship - Tug_6 ship - Sea rescue cruiser ship - Torpedo boat T56 ship - Yacht V12 tractor - Caterpillar 830m tractor - Claas Xerion tractor - Eicher Mammut tractor - Fendt Dieselross tractor - Fendt Vario 936 tractor - JCB Fastrac tractor - John Deere 8245R tractor - John Deere 8530 tractor - Kirovets K-700 tractor - Kirovets K-700A tractor - Lanz tractor - Lanz Bulldog tractor - MB-Trac tractor - MB-Trac 1100 tractor - MB-Trac 1800 tractor - Schlüter 1250VL tractor - Schlüter Compact 950 tractor - Schlüter Super 1500 TVL tractor - Unknown 01 truck - DAF XF 105 truck - Detroit Diesel truck - GAZ-66 truck - IVECO 140 E 30 truck - KRAZ 255-Truck - Kenworth W900-Truck - M35A2-Truck - MAN-Truck - MB Actros 2013-Truck - MB-NG-Truck - MB-SK 88-Truck - Mack-Truck - Scania 140 V8-Truck - Scania V8-Truck - Scania V8 with turbo whistle-Truck - Scania V8_1-Truck - Scania Vabis 56-Truck - Unimog 1600-Truck - Unimog 400-Truck - Unimog 406-Truck - Unimog 406_1-Truck - Ural-Truck - Volvo FH16-Turbine - 1-U-Boat - U96. The list is constantly being expanded.

Available immediately, delivery time: 1-4 days

Product number: 12334

€ 179,95 *

Subscriptions

Infrared receiver diode

1x infrared receiver diode.

Available immediately, delivery time: 1-4 days

Product number: 9844

€ 4,94 *

Subscriptions

Speakers 4 Ohm 90mm diameter

1x speaker 4 Ohm 90mm diameter 37mm depth, 25 watt music output Suitable for sound module USM-RC-2/RC-3. Seawater-resistant plastic membrane. LS-4R-25W-90. Weight: 230g. The speaker housing fits this: Article 9850.

Available immediately, delivery time: 1-4 days

Product number: 9849

€ 26,95 *

Subscriptions

King pin IR for Tamiya KB-IR-T with retaining clip for

1 king pin IR for Tamiya KB-IR-T with retaining clip for IR receiver BEIER.

Available immediately, delivery time: 1-4 days

Product number: 12267

€ 9,95 *

Subscriptions

Speaker case for LS-8R 15W-67

1x speaker housing for LS-8R-15W-67 Dimensions: 70x70x35mm. Suitable for speakers: item 9852 (not included).

Available immediately, delivery time: 1-4 days

Product number: 9853

€ 12,95 *

Subscriptions

1 adapter cable T-socket to Tamiya socket, approx. 10cm cable length

1 adapter cable T-socket to Tamiya-socket, approx. 10cm cable length, 1,5qmm. Deans T socket to Tamiya socket.

Available immediately, delivery time: 1-4 days

Product number: 11976

€ 4,25 *

Subscriptions

BEIER-Electronic Multiswitch Converter MSC-10-C

BEIER-Electronic Multiswitch Converter MSC-10-C. For Multi-Pro14. With the MSC 10-C multiswitch converters, the signals from 10 switches of the CARSON Reflex Stick MULTI PRO 14 channel can be combined and transmitted collectively.The Reflex Stick MULTI PRO 14 channel from CARSON-MODEL Sport is an inexpensive but fully equipped and technically high-quality 14-channel remote control system for universal use in many RC vehicles and ships.The MSC is plugged directly onto the receiver of the CARSON Reflex Stick MULTI PRO 14 channel and transmits the states of 10 switches of the remote control via just one proportional channel to the sound module USM-RC-2, USM-RC-3, SFR-1 or to the UFR-1230 of the UFR series.In this way, 10 switches can be used to control various functions of the sound module or the speed controller.Technical details: MSC-10-CEvaluates all 10 switchesChannels 5 - 14 of the receiver are connected to the MSC-10-C occupied.Channels 1 - 4 of the receiver remain free.All MSCs have dimensions (without receiver) of: 24 x 32 x 12 mm.Scope of delivery:Multiswitch converter moduleServo patch cable (30 cm)Instruction manual (German)Please note: Remote control and receiver are not included in delivery!The MSC modules work with these items:Sound speed controller SFR-1Double sound speed controller SFR-1-Double sound speed controller SFR-1-HLSound module USM-RC-2Sound module USM-RC-3Speed controller UFR-1230Double speed controller UFR-1230-D

Available immediately, delivery time: 1-4 days

Product number: 10516

€ 46,95 *

Subscriptions

Magnetic sensor LM-MS with magnet BEIER

1 LM-MS magnetic sensor with BEIER magnet.

Available immediately, delivery time: 1-4 days

Product number: 12269

€ 5,25 *

Subscriptions

Beier Sound Teacher USM-RC-3 USB stick. Includes content

1x Beier Sound Teacher USM-RC-3 USB stick. Includes the contents of the USM-RC-3 CD.

Available immediately, delivery time: 1-4 days

Product number: 12356

€ 8,50 *

Subscriptions

Output test board LED-8. For easy testing/checking

Output test board LED-8. For easy testing/checking of the outputs of various Beier modules. LED-8. A practical tool for checking the switching outputs of the following Beier modules: USM-RC-3 sound module, SFR-1 sound speed controller, SFR-1-D double sound speed controller, SFR-1-HL sound speed controller for Torro/Taigen and Heng Long tanks, UFR-1230 speed controller, UFR-1230-DM dual speed controller, SM-1 light modules LM-BT-16-4 and LM-IR-16-4. Caution: Not suitable for the USM-RC-2 sound module! With the LED output test board, the light settings of up to eight outputs can be easily displayed and checked. This board is particularly helpful during the planning and testing phases. All lighting functions, various settings, output sequences, and automatic or combined lights can be tested before the actual wiring. If there are problems with the lighting, you can quickly find out whether the problem is in the Sound Teacher settings or the wiring or hardware. The output test board is connected directly to the BEIER modules. The LEDs for outputs 1 and 2 light up red, outputs 3 and 4 green, outputs 5 and 6 yellow, and outputs 7 and 8 blue. The ribbon cable is approximately 20 cm long.

Available immediately, delivery time: 1-4 days

Product number: 12476

€ 9,95 * € 13,95 * (28.67% saved)

Subscriptions

Micro-SD card 32GB with SD adapter

1x Micro SD card 32GB with SD adapter.

Available immediately, delivery time: 1-4 days

Product number: 9818

€ 7,95 *

Subscriptions

Terminal for switching outputs For easy wiring

Terminal for switching outputs For easy wiring of BEIER USM-RC-2, 1230 UFR and EXM-2. AKL-10-W terminal with slot 10 series resistors.

Available immediately, delivery time: 1-4 days

Product number: 10325

€ 19,94 * € 19,95 * (0.05% saved)

Subscriptions

Switch for manual motor operation LM-SW on the Beier

1 switch for manual motor operation LM-SW on the Beier light module. For connection to the pin header X5 / 6 of a Beier light module LM-IR / BT-16-4.

Available immediately, delivery time: 1-4 days

Product number: 12270

€ 5,95 *

Subscriptions

Expansion module EXM-2 for USM-RC-2

1x extension module EXM-2 for the BEIER sound module USM-RC-2. Extension by 6 proportional and 10 switching outputs. At a glance: - 6 additional proportional channels - 10 additional switching outputs - 2 programmable servo outputs - Small motor controller - Easy programming via "Sound Teacher" Description: The extension module EXM-2 is connected to the proportional channel X2/1 of the sound module USM-RC-2 and increases the number of proportional channels by a further 6 channels. With the EXM-2, the sound module can be controlled via a total of 10 proportional channels. There are also 10 additional switching outputs on the EXM-2. Like the 12 switching outputs on the USM-RC-2, these can be assigned any light function and brightness. The EXM-2 contains 2 additional programmable servo outputs, which, like the two servo outputs on the USM-RC-2, can be positioned in up to 4 positions + 1 basic position. As a special feature, the EXM-2 also offers a small motor controller to which a motor for an auxiliary drive (e.g. turret rotation on a tank) can be directly connected. NOT suitable for the SFR-1 sound speed controller!

No longer available

Product number: 9809

€ 79,94 *

Subscriptions

Details

1x Y-cable with fuse holder For connection to rechargeable battery and Fa

1x Y-cable with fuse holder For connection to battery and travel controller With Dean's T-connector, fuse 4A. For Beier sound module. Matching connectors and couplings can be found as article 7835.

Available immediately, delivery time: 1-4 days

Product number: 10520

€ 11,95 *

Subscriptions

Switching module RC-SM-2

1x switching module RC-SM-2. 2 potential-free outputs, connection directly to the receiver. Switching current up to 0,4A. DISCONTINUED ITEM! The RC switching module RC-SM-2 has 2 outputs that can be switched via a proportional channel of an RC remote control. The RC-SM-2 is connected directly to an output of the remote control receiver via a servo cable. It is also possible to connect the switching module in parallel (e.g. with a Y-cable) to an existing servo or speed controller. Various additional sounds can be triggered on our sound modules via the two outputs. Many other applications are possible in which consumers are to be switched (e.g. lamps, LEDs, small motors, relays, etc.).By using PhotoMOS relays, the outputs are potential-free and can be designed as plus or minus switching by appropriate wiring.The standard version was originally developed for switching additional sounds and is therefore only designed for relatively small currents (max. 0,4 A).There is also a version called RC-SM-2H available, which can switch a current of max. 4 A per output.With 2 jumpers, you can choose between 4 switching variants:- Push button function- Switching function (memory switch)- Switching when the proportional signal changes (direction-dependent)- Switching when the proportional signal changes (movement-dependent)The switching thresholds or the sensitivity when the proportional signal changes can be set using a trimmer.The module is supplied with an approx. 30 cm long servo cable with a Graupner plug.The connections for the two outputs are designed as solder connections.Technical data:Required RC proportional channel:1Supply voltage: 4,8 - 6,0V (via RC receiver)Current consumption: approx. 10mASwitching outputs: 2 piecespotential-free, plus or minus switchingSwitching voltage: max. 40V DCSwitching current (per output): max. 0,4A for RC-SM-2max. 4,0A for RC-SM-2HSwitching variants:- Push button function- Switching function (memory switch)- Switching when the proportional signal changes (direction-dependent)- Switching when the proportional signal changes (movement-dependent)Switching threshold: Adjustable between 1,0-1,5 and 1,5-2,0 msDimensions: 39 x 25 x 13mmWeight: 11gItem is no longer available. Successor item: 11991.

No longer available

Product number: 9841

€ 18,94 *

Subscriptions

Details

BEIER-Electronic Multiswitch Converter MSC-8-C

BEIER Electronic Multiswitch Converter MSC-8-C. The MSC 8-C multiswitch converters allow the signals from 8 switches of the CARSON Reflex Stick MULTI PRO 14-channel system to be combined and transmitted. The Reflex Stick MULTI PRO 14-channel system from CARSON-MODEL Sport is an affordable yet fully equipped and technically advanced 14-channel radio control system for universal use in many RC vehicles and boats. The MSCs are plugged directly into the receiver of the CARSON Reflex Stick MULTI PRO 14-channel system and transmit the states of 8 switches from the radio control system to the USM-RC-2, USM-RC-3, SFR-1 sound module or the UFR-1230 of the UFR series via a single proportional channel. In this way, 8 switches can be used to control various functions of the sound module or the speed controller. Technical details: MSC-8-C: Evaluates 8 switches. Channels 5, 6, and 9-14 on the receiver are occupied by the MSC-8-C. Channels 1- Pins 4, 7, and 8 of the receiver remain unused. All MSC modules have dimensions (without receiver) of 24 x 32 x 12 mm. Package contents: Multiswitch Converter Module, Servo Patch Cable (30 cm), Instruction Manual (German). Please note: Transmitter and receiver are not included! The MSC modules are compatible with the following items: Sound Speed Controller SFR-1, Dual Sound Speed Controller SFR-1-D, Dual Sound Speed Controller SFR-1-HL, Sound Module USM-RC-2, Sound Module USM-RC-3, Speed Controller UFR-1230, Dual Speed Controller UFR-1230-D

Available immediately, delivery time: 1-4 days

Product number: 10515

€ 44,95 *

Subscriptions

UFR-1230-D dual speed controller from BEIER. Specially designed for

1x UFR-1230-D dual speed controller from BEIER. Specially developed for tracked vehicles. With 8 outputs for lighting. Adjustable via the Drive-Teacher software. Speed controller for two DC brushed motors. Specially developed for tracked vehicles/ships. Powerful BEC with 5,6V 3A. Optional load control, inertia, and handbrake function. Highly adjustable via the "Drive Teacher." The speed controller is characterized by its high sensitivity. The control is very realistic and dynamic, guaranteeing absolute driving pleasure. Thanks to its diverse setting options, the speed controller can be easily and individually adapted to the most diverse model requirements and driving characteristics. The settings are made via a DIP switch or with the help of the "Drive Teacher." The model's lighting can be connected directly to the speed controller via the 8 light outputs. All lighting and additional functions of the speed controller can be controlled via Nautic and Multiswitch modules.Features:-Supply voltage: 6-18V-Max. Motor current 2x 30 A (continuous) 60 A (short-term) - PWM clock frequency 20 or 40 kHz - 8 switching outputs for the lighting - Powerful BEC 5,6 V 3 A short-circuit proof - 3 proportional inputs (throttle 1, throttle 2, steering, control) - 2 proportional outputs (for sound module) - Mailsafe in case of reception interference (motor stop) - Start-up protection when switched on - Battery voltage monitoring - Temperature monitoring - Short-circuit protection motor output stage Selectable via DIP switch: - Load control on/off - Hand brake function on/off - Hand brake function on/off - Selection of battery type: LiPo/other type - Learning function (setup) for throttle channel on/off Adjustable via Drive Teacher (K-USB-2 required!): - Firmware update - Diagnostics - Channel inversion - Switch-off undervoltage monitoring - Reduction of reversing speed to 50% - Selection of PWM clock frequency 20 or 40 kHz - Load control setting - Activation/adjustment of the mass inertia - Activation of the emergency brake function - Handbrake hardness setting - Adjustment of the 2 throttle curves - Configuration of the switching outputs (output type, brightness, xenon) - Configuration of the light switch - Configuration of the control channel - Configuration of Nautic / Multiswitch modules The speed controller is delivered with a standard configuration and is ready for immediate use! The data cable is therefore only required if settings of the standard configuration need to be changed. Technical specifications: - Dimensions: 80 x 50 x 23 mm - Weight: 95 g - Connection cable: 2 x 2,5 mm², 25 cm long with Deans T-connector - Motor connection cable: 4 x 2,5 mm², approx. 25 cm long - Servo cable to the receiver: 3 x 0,14 mm², 30 cm long.

Available immediately, delivery time: 1-4 days

Product number: 10776

€ 169,94 * € 169,95 * (0.01% saved)

Subscriptions

Speaker case for LS-4R 25W-90

1x speaker housing for LS-4R-25W-90 Dimensions: 120x120x60 mm.

Available immediately, delivery time: 1-4 days

Product number: 9850

€ 14,95 *

Subscriptions

SFR-1-D DOUBLE sound speed controller from Beier. Specially

1x SFR-1-D DOUBLE sound speed controller from Beier. Specially developed for tanks, construction vehicles and ships. Incl. 16 switching outputs. Can be adjusted with SFR-1-D Sound Teacher. WITH CD-ROM/DVD. DOUBLE speed controller for DC brush motor, sound module and light control module in one! Specially developed for tanks/construction machines/ships. Powerful BEC with 5,6V/3A. Optional load control, mass/steering inertia and brake function. Can be adjusted in great detail using the "Sound Teacher SFR-1-D". The speed controller is characterized by its high sensitivity. The controls are very realistic and dynamic and guarantee absolute driving pleasure. For all types of models with TWO drive motors and a standard transmitter. - Thanks to a wide range of setting options, the speed controller can be easily and individually adapted to the most diverse model requirements and driving characteristics. All settings are made using the "Sound Teacher SFR-1-D" - the convenient configuration program from BEIER-Electronic. The model's lighting can be connected directly to the speed controller via the 16 light outputs. The speed controller also has 2 mini speed controllers for auxiliary drives.Features:-Supply voltage: 6-18V-Max. 2x motor current 30 A (continuous) 60 A (short-term) - 16 switching outputs for the lighting - Powerful BEC 5,6 V 3 A - 8 proportional inputs (throttle, steering, servos, sound, light) - 4 programmable proportional outputs (servo outputs) - Failsafe for proportional inputs in the event of reception interference (motor stop) - Start-up protection when switched on - Battery undervoltage monitoring, programmable - Temperature monitoring - Short-circuit protection for the motor output stage - Short-circuit protection for the BEC - Short-circuit protection for switching outputs. Can be selected via the SFR-1-D sound teacher: - Load control on/off - Various integrated mixers - Brake function incl. Hand and emergency brake adjustable via Sound Teacher SFR-1-D (K-USB-2 required!): - Firmware update - Diagnostics - Channel inversion - Programming - Undervoltage monitoring - PWM clock frequency selection - Mass inertia activation/adjustment - Steering inertia activation/adjustment - Handbrake hardness adjustment - Throttle curve adjustment - Switch output configuration (output type, brightness, xenon) - Light switch configuration - Control channel configuration. The speed controller is delivered with a standard configuration and is ready for operation! Protection functions: Short circuit protection motor output stage, short circuit protection switching outputs, short circuit protection BEC system, temperature monitoring, battery undervoltage monitoring, start-up protection, failsafe for proportional inputs. Scope of delivery: - Battery connection 2x 1,5mm², 25cm long, DEANS T-plug - 2x servo cables for connection to receiver, 30cm Long speaker connection cable, 25cm; cable for standby switch or volume potentiometer, 25cm; 1x 40cm flat ribbon cable for connecting the switching outputs; Micro SD card (4GB) plus adapter; DVD interface: programming interface for data cable; K-USB-2 manual; Technical data: Ambient temperature: 0-60°C; Dimensions: 88 x 60 x 25 mm, with SD card: 88 x 63 x 25 mm; Weight: 100g

Available immediately, delivery time: 1-4 days

Product number: 11841

€ 309,95 *

Subscriptions

King pin BT for Tamiya KB-BR-T with retaining clip for

1 king pin BT for Tamiya KB-BR-T with retaining clip for the BEIER magnetic sensor.

Available immediately, delivery time: 1-4 days

Product number: 12268

€ 9,95 *

Subscriptions

1x Y-cable with fuse holder For connection to rechargeable battery and Fa

1x Y-cable with fuse holder For connection to battery and travel controller With Dean's T-connector, fuse 4A. For Beier sound module.

Available immediately, delivery time: 1-4 days

Product number: 10819

€ 11,95 *

Subscriptions

USB stick Sound-Teacher SFR-1 from Beier. With content DVD

1x USB stick Sound-Teacher SFR-1 from Beier. With contents of the CD SFR-1.

Available immediately, delivery time: 1-4 days

Product number: 12355

€ 8,50 *

Subscriptions

Terminal with constant current outputs

1x connection terminal with constant current outputs AKL-10-K, allows the connection of LEDs without a series resistor. No soldering work thanks to spring clamps. Suitable for BEIER USM-RC-2 and EXM-2. The AKL-10-K enables easy connection of LEDs to the sound module USM-RC-2 and to the extension module EXM-2 without additional soldering work. The constant current source has 10 separate and current-limited outputs for directly controlling LEDs. Each constant current source delivers a current of approx. 20 mA, regardless of the supply voltage, making it easy to connect LEDs without additional series resistors.The constant current source can be plugged directly into the sound and expansion module using the ribbon cable provided.The battery voltage is connected to the black screw terminal.The lighting can now be wired up easily without additional soldering using the spring-loaded terminals of outputs 1 - 10.Technical data:Supply voltage (Ub):Double screw terminals for the supply voltageCurrent consumption: Quiescent current: approx. 10 mA, + 20 mA per outputOutputs:10 piecesPlus (anode) and minus (cathode) of the LEDs must be connectedConnection cable: 10-pin ribbon cable, 20 cm long, can be plugged directly into the sound moduleDimensions:53 x 52 x 20 mmWeight:35 g

No longer available

Product number: 9820

€ 39,95 *

Subscriptions

Details

Switching module RC-SM-2H

1x switching module RC-SM-2H 2 potential-free outputs, connection directly to the receiver. Switching current up to 4A. The RC switching module RC-SM-2 has 2 outputs that can be switched via a proportional channel of an RC remote control. The RC-SM-2 is connected directly to an output of the remote control receiver via a servo cable. It is also possible to connect the switching module in parallel (e.g. with a Y-cable) to an existing servo or speed controller. Various additional sounds can be triggered on our sound modules via the two outputs. Many other applications are possible in which consumers are to be switched (e.g. lamps, LEDs, small motors, relays, etc.).By using PhotoMOS relays, the outputs are potential-free and can be designed as plus or minus switching by appropriate wiring.The standard version was originally developed for switching additional sounds and is therefore only designed for relatively small currents (max. 0,4 A).There is also a version called RC-SM-2H available, which can switch a current of max. 4 A per output.With 2 jumpers, you can choose between 4 switching variants:- Push button function- Switching function (memory switch)- Switching when the proportional signal changes (direction-dependent)- Switching when the proportional signal changes (movement-dependent)The switching thresholds or the sensitivity when the proportional signal changes can be set using a trimmer.The module is supplied with an approx. 30 cm long servo cable with a Graupner plug.The connections for the two outputs are designed as solder connections.Technical data:Required RC proportional channel:1Supply voltage: 4,8 - 6,0V (via RC receiver)Current consumption: approx. 10mASwitching outputs: 2 piecespotential-free, plus or minus switchingSwitching voltage: max. 40V DCSwitching current (per output): max. 0,4A for RC-SM-2max. 4,0A for RC-SM-2HSwitching variants:- Push button function- Switching function (memory switch)- Switching when the proportional signal changes (direction-dependent)- Switching when the proportional signal changes (movement-dependent)Switching threshold: Adjustable between 1,0-1,5 and 1,5-2,0 msDimensions: 39 x 25 x 13mmWeight: 11g

No longer available

Product number: 9842

€ 23,95 *

Subscriptions

Details

Beier mini sound module MSM-1. Completely pre-configured

1x Beier mini sound module MSM-1. Fully preconfigured sound and light module for RC models and thus a simple plug & play sound module that is very suitable for beginners. The MSM-1 at a glance Control of sound + light in one unit Control Suitable for many model types 14 different model types with all sound and light settings Plug & Play - ideal for beginners No computer required for model selection or other settings Supply voltage between 5 - 14 V DC 6 proportional inputs for controlling sound and light functions with a standard remote control Model types 3 x Trucks 2 x Cars 1 x Emergency Vehicle 1 x Tractor 2 x Construction Vehicles 2 x Tanks 3 x Ships Sound Driving sounds for 14 different model types Various additional sounds depending on the model type: e.g. Horn, fanfare, ship's horn, cannon shot, machine gun fire, radio message, hydraulic noise, animal noises, siren, announcements. Optimal sound thanks to integrated, powerful amplifier. Light. 8 outputs for connecting LEDs, lamps, relays, etc. Different outputs depending on model type: e.g. Lights, indicators, brake lights, reversing lights, cannon flash, machine gun flash, warning lights, speed cameras. Connection for an IR light module to forward the light and servo signals to semi-trailers and trailers. Accessories (not included): Speaker with housing. Terminals for easy connection of LEDs. Battery Y-cable for parallel connection of sound module and speed controller to the battery. Volume potentiometer for manual volume adjustment. Description: The MSM-1 is a fully preconfigured sound and light module for RC models and thus a "simple" plug & play sound module that is very suitable for beginners. 14 different model types with all sound and light settings are permanently stored in the memory. There are:3 trucks2 cars1 emergency vehicle1 tractor2 construction vehicles2 tanks3 shipsThe desired model can be easily selected using a standard RC transmitter. No software, computer or other programming hardware is required to select the model. The MSM-1 has 6 proportional inputs that can evaluate 6 channels of an RC receiver. The 1. Channel is always the gas channel, the 2nd In most models the channel is the steering. Additional sounds and lights can be controlled via the remaining 4 channels. The sound and light functions vary depending on the model type. To realize various lighting effects, the MSM-1 has 8 switching outputs to which LEDs, lamps and relays can be connected. Lighting functions such as low beam, reversing light, brake light, indicators, hazard lights, etc. can be controlled easily and in accordance with sound and movement. Each of the 14 pre-configured models has its own driving sound (engine sound) and additional sounds suitable for the model type, which can be triggered via the RC transmitter. Attention: The sounds and settings of the 14 models cannot be changed on the MSM-1! If you want to change sounds or other settings yourself or can be adapted, we recommend the USM-RC-3 sound module. The MSM-1 can also be seen as a "simple" plug & play sound module and is very suitable for beginners. Technical data Supply voltage (Ub): 5 to 14 V DC Current consumption: Quiescent current: approx. 60 mAOperation: depends on volume and loadProportional inputs: 6 PWM (1,000 - 2,000 ms)Switching outputs: 8 minus switching - open collector:max. 1,5 A per output, total current of all outputs must not exceed 3,0 A. AF amplifier: 20 W. Recommended speakers: 4 - 8 Ohm. Volume adjustment: via external potentiometer (100 kOhm) and/or remote control. Sound data storage: internal 64 MB flash. Sound output: 16-bit, mono, 22 kHz. Model types: 14 models. 3 x trucks, 2 x cars, 1 x emergency vehicle, 1 x tractor, 2 x construction vehicles, 2 x tanks, 3 x ships. Available sounds: Driving sounds (starting sound, shutting off sound, starting sound, stopping sound, idle sound, braking sound, reversing warning, curve squeal, indicator sound). Various additional sounds depending on the model (horn, compressed air fan, ship's horn, depth sounder, turret rotation, machine gun, cannon shot, radio message, animal sounds, hydraulic sound, siren, announcements). Additional interfaces: Interface for data cable K-USB-2 (currently not functional!) or IR transmitter diode for light modules LM-IR-8-1 and LM-IR-16-4Protection functions:Current monitoring of the switching outputsPermissible ambient temperature: 0 to 60°CPermissible relative humidity: Max. 85% Dimensions: 51 x 33 x 17 mm Weight: 18 g Scope of delivery Mini sound module MSM-1 Instruction manual (German and English) 6 servo patch cables (30 cm) for connection to an RC receiver 1 connection cable (25 cm) for speaker 1 ribbon cable (40 cm) for connecting the switching outputs Fuse holder with 4 A fuse

Available immediately, delivery time: 1-4 days

Product number: 13183

€ 119,94 *

Subscriptions

Bluetooth transmitter module Beier LM-BT-S. For use with

1 Beier LM-BT-S Bluetooth transmitter module. For use with the light module LM-BT-16-4.

Available immediately, delivery time: 1-4 days

Product number: 12264

€ 21,96 *

Subscriptions

Road-Train adapter IR RTA

1x Road Train Adapter IR-RTA This module allows you to create trains with multiple trailers. The Road Train Adapter IR-RTA allows you to forward the IR signal sent from the USM-RC-2 sound module to the semi-trailer/trailer to another trailer. This allows you to create trains with multiple trailers. A Road Train Adapter is required for each IR signal forwarding to the next trailer. Each trailer requires an SM-IR-16-2 light module and a battery. The light and servo functions are the same on each trailer. It is therefore not possible, for example, to control a servo output differently on the first and second trailer. Technical specifications: Supply voltage (Ub): 5V DC (from SM-IR-16-2) Current consumption: approx. 10 mA Inputs: Outputs: 1 IR transmitter diode (cable length approx. 100 cm) Permissible ambient temperature: 0 - 60°CDimensions: Weight:

Available immediately, delivery time: 1-4 days

Product number: 9846

€ 29,95 *

Subscriptions

1 adapter cable T-socket to XT60 plug approx. 10cm cable length

1 adapter cable T-socket to XT60-plug approx. 10cm cable length, 1,5qmm. Deans T socket to XT60 plug.

Available immediately, delivery time: 1-4 days

Product number: 11975

€ 4,25 *

Subscriptions

Micro SD card reader

1x Micro-SD card reader.

Available immediately, delivery time: 1-4 days

Product number: 9819

€ 6,25 *

Subscriptions

PAGE

Beier Electronic

Filter products