Kraftwerk

PAGE

KraftwerK control pad Light & Sound. Control pad for all

KraftweK control pad Light & Sound. Control pad for all transmitters for a power plant lighting system. The pad is connected to a free proportional channel in the transmitter and behaves like a normal joystick, i.e. no complex transmission signals are used as with most multiswitches, which means that it should be usable in any remote control transmitter.The control pad Light & Sound switches all light functions, the trailer supports, the tipping trough, the fifth wheel coupling and 11 additional functions (e.g. a rotating light), the gear shift and 2 servos. There is also a button for "everything on" and "everything off" if you need to do something quickly! Dimensions: 78x33mmThe pad is compatible with all remote control transmitters.It is important that the selected channel is a proportional channel, i.e. a servo on the corresponding receiver output must be able to be controlled continuously. (Switching channels are unsuitable!!!) Ideally, the channel should be free, i.e. no other control device (joystick, linear regulator, ...) should be connected. Since new transmitters often no longer have any extension channels, an occupied channel can also be used in an emergency, but this must not be in use and must always be in the middle position (otherwise the functions will not switch).

Available immediately, delivery time: 1-4 days

Product number: 11089

€ 74,90 *

Subscriptions

1x KLB 8-500 expansion board. The expansion board

1x KLB 8-500 expansion board. The expansion board offers the possibility of expanding the light assistant by a further 8 outputs. Plug & Play solution. The module, which is only 21 x 26 mm in size, offers the possibility of expanding the light assistant by a further eight outputs - with a load capacity of up to 500 mA. It is simply connected to one of the EasyBus outputs of the light assistant and is thus automatically integrated into the system. The outputs of the expansion board offer exactly the same functionality as the outputs of the light assistant. - In addition to some effect lighting, all the usual lighting functions in the original are available: - combined front light (parking light, low beam, high beam, headlight flasher and fog light) - combined rear light (parking light, brake light, rear fog light) - American rear light (parking light, brake light, indicator) - daytime running light with automatic lowering when indicator is activated - cornering light - cornering light - reversing light - indicator, hazard warning light, American indicator - multi-flashing light - running light - rotating light - KnightRider In addition to the basic behavior of the individual outputs, the brightness, the switching on and off speed, as well as the switching on and off duration for flashing functions can also be set. Dimensions: 23x28x13mm Number of switching outputs: 8 Current load capacity per output: 500mA Voltage at the + output: BEC voltage (5-6V)LED resistor integrated: noPower supply: via bus (BEC of the speed controller)Max. own power consumption: 25mA

Available immediately, delivery time: 1-4 days

Product number: 9245

€ 34,90 *

Subscriptions

1x BUS - distribution. 1 6 on. Let this distribution

1x BUS distributor. 1 to 6. With this distributor, the EasyBus outputs of the light assistants can be divided into a further 6 outputs. Plug & Play solution. With this distributor, the EasyBus outputs of the light assistants can be divided into a further 6 outputs. Connection cable with a length of approx. 15 cm.

Available immediately, delivery time: 1-4 days

Product number: 9255

€ 4,90 *

Subscriptions

EasyBus replacement cable 30cm long, 1-sided with post coupling

EasyBus replacement cable 30cm long. 1-sided with post coupling. 1 side open wire ends.

Available immediately, delivery time: 1-4 days

Product number: 12168

€ 2,80 *

Subscriptions

1x KLB 8-20 expansion board. The expansion board bie

1x KLB 8-20 expansion board. The expansion board offers the possibility of expanding the light assistant by a further 8 outputs. Plug & Play solution. The module, which is only 15 x 28 mm in size, offers the possibility of expanding the light assistant by a further eight outputs - capable of handling up to 20 mA. It is simply connected to one of the EasyBus outputs of the light assistant and is thus automatically integrated into the system. The outputs of the expansion board offer exactly the same functionality as the outputs of the light assistant. - In addition to some effect lighting, all the usual lighting functions in the original are available: - combined front light (parking light, low beam, high beam, headlight flasher and fog light) - combined rear light (parking light, brake light, rear fog light) - American rear light (parking light, brake light, indicator) - daytime running light with automatic lowering when indicator is activated - cornering light - cornering light - reversing light - indicator, hazard warning light, American indicator - multi-flashing light - running light - rotating light - KnightRider In addition to the basic behavior of the individual outputs, the brightness, the switching on and off speed, as well as the switching on and off duration for flashing functions can also be set. Dimensions: 15x28x13mm Number of switching outputs: 8 Current load capacity per output: 20mA Voltage at the + output: BEC voltage (5-6V)LED series resistor integrated: yes (180 Ohm)Power supply: via bus (BEC of the speed controller)Max. own power consumption: 25mA

Available immediately, delivery time: 1-4 days

Product number: 10114

€ 29,90 *

Subscriptions

Details

BUS - distribution. 1 to 6. 60cm. Power plant zone

BUS distributor. 1 to 6. 60cm With this distributor, the EasyBus outputs of the light assistants can be divided into 6 additional outputs. Plug&Play solution. Board size approx. 24x15mm.

Available immediately, delivery time: 1-4 days

Product number: 10448

€ 8,25 *

Subscriptions

1x KLM 4 / 16 light assistant. The light assistant is the

1x KLM 4/16 light assistant. The light assistant is the core component of a lighting system that can be expanded as required. Incl. Transmitting diode. Plug & Play solution. Core component of the lighting system, compatible with all sound modules, speed controllers and the Tamiya MFU-xx. The EasyBus lighting systems are equipped with different lighting boards, IR trailer lighting, etc. expandable.The PC software can be downloaded free of charge. No programming knowledge is required. The control can be customized down to the smallest detail. Technical data: - Dimensions 51x36x13 mm - 4 inputs (steering, throttle, channel 1, channel 2) - 2 servo outputs (steering servo, speed controller) - 5 bus outputs (for expansion modules) - 16 switching outputs with max. 500mA, freely configurable-1x USB socket (Micro-USB, for configuration)From April 2018 incl. Transmitter diodeWe are of course happy to configure the lighting system according to your ideas and also save them.The KLM 4/16 light assistant is the further development of the KLM 4/12-500. Compact design, easy operation and compatibility with the most common systems on the market are its main strengths. It is compatible with standard forward-reverse speed controllers (with or without a separate brake), with the cruise control controllers from Servonaut and all sound modules. The light functions can be controlled in a variety of ways; please refer to the manual for details. The module, which is only 52 x 36 x 13 mm in size, offers eight high-current outputs (500 mA each and eight switching outputs with integrated series resistors), four adjustable servo outputs, an infrared output, a USB socket that is only required for configuration and five bus outputs, via which the system can be expanded as required with additional switching, servo or motor functions. Standard assignment of the outputs:-Output 1 & 2: parking light & high beam & headlight flasher-Output 3 & 4: dipped beam-Output 5: left indicator-Output 6: right indicator-Output 7 & 8: tail light & brake light-Output 9: rear fog light-Output 10: reversing light-Output 11 & 12: speed camera-It is possible to select the behavior of each individual output completely independently and freely via PC and to configure it on a percentage basis. In addition to some effect lighting, you can choose from all the usual lighting functions in the original: -- combined front light (parking light, low beam, high beam, headlight flasher and fog light) -- combined rear light (parking light, brake light, -- American rear light (parking light, brake light, indicator) -- daytime running light with automatic lowering when the indicator is activated -- cornering light -- curve light -- reversing light -- indicator, hazard warning light, American indicator -- multi-flashing light -- running light -- rotating light -- KnightRider In addition to the basic behavior of the individual outputs, the brightness, the switching on and off speed, and the switching on and off duration for the flashing functions can also be set. How easy this is can be tested in advance using the demo mode of the free PC software ControlPanel. The module is connected to four channels of the receiver. In addition to gas and steering, two channels (K1 and K2) are used to control the lighting. Please refer to the manual for the different variants! During development, special attention was paid to ease of use. You do not need any electronic experience to use this system! You will find all the information you need in the included quick start guide!

Available immediately, delivery time: 1-4 days

Product number: 10822

€ 114,89 *

Subscriptions

EASYBUS adapter. 6-fold 15cm / JR-Steck. With this adapter

EASYBUS - adapter. 6-way 15cm/JR plug. With this adapter, the EasyBus lighting boards can be connected to the Beier, Brixl and Arduino systems. Plug & Play solution. For the use and control of Kraftwerk lighting boards, the following can be found in the Beier SFR-1 manual:From the Beier manual:The SFR-1 can also directly control the EasyBus lighting boards from Kraftwerk. This makes connecting the lighting much easier. The signal for the EasyBus lighting boards is available at slot X5/1 on the SFR-1. Attention: An EasyBus adapter with a suitable connection (servo plug) is required here!Please note: The EasyBus adapter is connected to connection X5/1 (Servo 1) on the SFR1. Therefore, servo output X5/1 can no longer be used to connect a servo!

Available immediately, delivery time: 1-4 days

Product number: 11382

€ 9,90 *

Subscriptions

EasyBus lighting boards for 7 chamber taillights

EasyBus lighting boards for 7-chamber rear lights from Carson/Veroma. Suitable for the EasyBus system. The plug & play solution. The modules are each equipped with seven SMD LEDs and have an output with a series resistor on the back for free assignment (for example, for a marker light or license plate light). They are connected to the Easybus outputs of the light assistants. Simply plug in... Done! Each of the eight outputs can be changed as usual with the Kraftwerk ControlPanel and thus adapted to your own ideas. Attention: Since we use larger and brighter LEDs, the back panel of the lamp body must be removed. Unfortunately, this also eliminates the holes for the fastening screws, which is why the lamp bodies must be glued to the model.

Available immediately, delivery time: 1-4 days

Product number: 10349

€ 59,80 *

Subscriptions

Kraftwerk RS1 controller, sound module and lighting system

The RS1 combines a speed controller, sound module and lighting system in a compact 6-20V module. 25A to 32kHz brush and coreless motor. Robust speed controllerThe speed controller can be permanently loaded with 25A and, thanks to the 32kHz control, is also suitable for bell-armature motors. It offers manual transmission support for up to four gears, a clutch function, handbrake, optional inertia simulation and a cruise control function, which does not work like the competition (stick deflection controls acceleration), but like the original: the throttle deflection controls the speed and the cruise control is activated by pressing a button. Pressing the button again or braking deactivates the cruise control.Extraordinary soundKraftwerK is once again setting standards in programmability. While the competition can only use a few sound snippets for the driving sound, KraftwerK can use as many as you like and it works as follows: First, the speed range is defined, e.g. 500 rpm immediately after starting and 2300 rpm when the engine is running out. Then sound snippets are stored for any number of areas and defined with base speed, minimum and maximum. At minimum, the sound is faded in at the speed, at base speed it is played at full volume and 1:1 speed, and up to maximum it is again adjusted to the speed and finally faded out. The snippets can and should of course overlap, which can create an ultra-realistic sound. In total there are three sound tracks: 2x acceleration and 1x deceleration. The first sound track is the normal driving sound, the second sound track can either be mixed proportionally as a load or switched. The third sound track is the delay sound and is automatically added when you release the joystick. If that's too complicated for you, you'll be pleased to know that 3 high-quality sounds are already included with the module. In the future there will also be a sound library with premium sounds that can be purchased for a few euros and downloaded via the ControlPanel and saved on your own module.Unlimited expandabilityKraftwerK's leading role in the field of RC bus systems is now fully evident in the RS1. The RS6 can be expanded as required via the 1 EasyBus outputs. Lighting boards, switching extensions, servo controls and much more can be controlled via the EasyBus. But the RS1 has one more special gimmick: on the upper side there are four individual sockets that are barely visible and can be used to plug in another module. The first module in this series is the BL8A, an 8A brushless controller designed for hydraulic pumps.Versatile connections / technical dataBattery (6 - 20V)Motor 25A, up to 32kHz, brush and bell-armature motor5 servo inputs or SUMD, IBUS, SBUS, CPPM5 servo outputs6 bus outputs8 switching outputs 500mA2 switching outputs 10AInfrared transmitter (diode included)Dimensions 63x44x28mmProperties of the drive controllerOperating voltage 6-20VBEC 6V / 3ATimension frequency adjustable up to 32kHZClutch functionHandbrake functionManual transmission supportAdjustable inertia simulationAdjustable cruise controlProtection functions: battery undervoltage, motor short circuit, overtemperatureFunctions for servo outputsProportional functionProportional function directPropFunction switchedTwo positionsThree positionsFifth wheel plateTrailer supports MotorDump/tipper MotorRamp/Platform MotorManual transmissionSound featuresUnlimited number of sounds10-15 sounds that can be played simultaneouslyPlayback modes: Touch, loop, once, permanent, random, stop pointsFormats: WAV, MP3 Usable sampling rate: All (automatic conversion to 44.100)Volume control: Potentiometer, via channel, via softwareSD card: max.

Available immediately, delivery time: 1-4 days

Product number: 12644

€ 269,90 *

Subscriptions

EasyBus lighting boards for 7 chamber taillights

Available immediately, delivery time: 1-4 days

Product number: 11005

€ 183,63 * € 184,90 * (0.69% saved)

Subscriptions

KIEB 6 / 2 / 2 Infrared Receiver. Power plant plug & play solution

KIEB 6/2/2 infrared receiver. Plug & play solution. Suitable for the EasyBus system. Power plant zone. KIEB 6/2/2 infrared receiver. Plug & play solution. Suitable for the EasyBus system. Power plant zone. KIEB 6/2/2 receives all EasyBus information from the infrared transmitter.Plus: incl. 5 mm receiver diode, six switching, two servo, two motor and three EasyBus outputsTechnical data:Length (excl. pin length): 60mmWidth: 40mmHeight: 12.5mmVoltage: 4-5 cells (max. 8V)BEC: 5V (1A)Switching outputs: 6Servo outputs: 2Motor outputs: 2EasyBus outputs: 3Bridgeable distance: up to 1.5mMaximum angle: approximately 90°KIEB 6/2/2KraftweK infrared receiver with bus outputs and 6 switching, 2 servo and 2 motor outputs.With the KIEB 6/2/2 infrared receiver you can control the trailer supports and a trough or ramp via the two integrated motor outputs. Doors, lift axles or steering axles can be controlled via the two servo outputs. Additional lighting or rotating beacons can be controlled via the switching outputs. As usual, bus extensions (switching, servo or motor extensions) can be connected to the three bus outputs.

Available immediately, delivery time: 1-4 days

Product number: 10446

€ 109,90 *

Subscriptions

1x KIES infrared transmitter. Plug & Play solution

1x KIES infrared transmitter. Plug & Play solution. Incl. IR transmitter diode. Suitable for the EasyBus system. Technical data: - Dimensions 27,5x17x7,5 mm - Power supply via EasyBus - 1 servo output (adjustable) Scope of delivery: - 1x KIES infrared transmitter - 1x IR transmitter diode The infrared transmitter is simply plugged into a free connection on the EasyBus and is immediately ready for use. It not only transmits the light functions of EasyBus but also servo functions to the infrared receiver (not included). Items 9252 and 9253 are available as suitable infrared receivers.

Available immediately, delivery time: 1-4 days

Product number: 9254

€ 34,90 *

Subscriptions

EasyBus Lighting System KLM 4 / 16 TAMIYA MAN TGX 18.540 / 26.540

EasyBus lighting system KLM 4/16 for Tamiya MAN TGX 18.540 / 26.540 The lighting system for the TAMIYA MAN TGX 18.540 / 26.540 with the new KLM 4/16, ready-to-install lighting boards and integrated infrared transmitter.The lighting boards are simply inserted into the light chambers from behind and are held in place by a press fit.The system is controlled by a KLM 4/16, which is compatible with normal forward-reverse speed controllers (with or without separate brake), cruise control controllers and all sound modules.The lighting functions can be controlled either with our control pad or in numerous other ways, for details please refer to the online manual.This starter set includes a complete lighting system for the MAN TGX 18.540 / 26.540 from TAMIYA and consists of two front lighting boards with wired LEDs for the side Indicators, underrun protection and marker lights, as well as a light assistant KLM 4/16.br>The lighting boards are connected directly to the KLM 4/16 and can also be configured via this with our Kraftwerk ControlPanel. Brightness, flashing speeds, but also the basic functionality (e.g. should the high beam be switched on at the output) can be set separately for each output. Information about this can be foundHighlights & DetailsKLM 4/16 (4 servo inputs, 16 switching outputs, 5 bus outputs) Ready-to-install lighting boardsPlug & Play solution (connect and drive)Compatible with all sound modulesCompatible with all speed controllersCompatible with Tamiya MFUCan be expanded with a wide variety of lighting boardsCan be expanded with infrared for trailer lightingCan be adapted to the model down to the smallest detail using a PCNo programming knowledge requiredPC software can be downloaded free of chargeTechnical specificationsPower supply:via receiver power supply (BEC of the speed controller)Max. Power consumption 20mA per device and 20mA per LEDLEDs at the front (per side):yellow: 1x 3mmwhite: 2x 3mm, 3x 5mm, 1x SMDyellow wired: 1x 3mmwhite wired: 1x 3mmUltra-bright high-performance LEDsAdditional outputs at the front 3 with 180 Ohm resistance eachLEDs at the rear (per side):red: 4x SMD 1206yellow: 1x SMD 1206white: 1x SMD 1206Ultra-bright high-performance LEDsAdditional outputs at the rear 1 each with 180 Ohm resistanceScope of deliveryLight assistant KLM 4/16four ready-to-install lighting boards (2x front, 2x rear)

Available immediately, delivery time: 1-4 days

Product number: 11001

€ 230,81 *

Subscriptions

EasyBus replacement cable 60cm long, 1-sided with post coupling

EasyBus replacement cable 60cm long. 1-sided with post coupling. 1 side open wire ends.

Available immediately, delivery time: 1-4 days

Product number: 12169

€ 2,98 *

Subscriptions

EasyBus lighting system KLM 4 / 16 TAMIYA MB Actros 3363

EasyBus lighting system KLM 4/16 for Tamiya Mercedes-Benz Actros 3363 The lighting system for the TAMIYA Actros 3363 with the new KLM 4/16, ready-to-install lighting boards and integrated infrared transmitter.The lighting boards are simply inserted into the light chambers from behind and are held in place by a press fit.The system is controlled by a KLM 4/16, which is compatible with normal forward-reverse speed controllers (with or without separate brake), cruise control controllers and all sound modules.The lighting functions can be controlled either with our control pad or in numerous other ways, for details please refer to the online manual.This starter set includes a complete lighting system for the Mercedes-Benz Actros 3363 from TAMIYA and consists of two front lighting boards with wired LEDs for the side indicators, underrun protection and marker lights, as well as a light assistant KLM 4/16.br>The lighting boards are connected directly to the KLM 4/16 and can also be configured with our Kraftwerk ControlPanel. Brightness, flashing speeds, but also the basic functionality (eg: should the high beam be switched on at the output) can be set separately for each output. Information about this can be foundHighlights & DetailsKLM 4/16 (4 servo inputs, 16 switching outputs, 5 bus outputs) Ready-to-install lighting boardsPlug & Play solution (connect and drive)Compatible with all sound modulesCompatible with all speed controllersCompatible with Tamiya MFUExpandable with a wide variety of lighting boardsExpandable with infrared for trailer lightingCan be adapted to the model down to the smallest detail using a PCNo programming knowledge requiredPC software can be downloaded free of chargeTechnical dataPower supply:via receiver power supply (BEC of the speed controller)Max. power consumption 20mA per device and 20 mA per LEDLEDs at the front (per side):

Available immediately, delivery time: 1-4 days

Product number: 11003

€ 269,89 *

Subscriptions

Machined housings for 7 chamber taillights (1 pair)

1 pair of machined housings for the 7-chamber rear lights from Veroma. Modified to fit the lighting boards 10349.

Available immediately, delivery time: 1-4 days

Product number: 10686

€ 29,90 *

Subscriptions

EasyBus lighting system KLM 4 / 16 for Tamiya Arocs 3348

EasyBus lighting system KLM 4/16 for Tamiya Mercedes-Benz Arocs 3348/4151. The lighting system for the TAMIYA Arocs 3348/4151 with the new KLM 4/16, ready-to-install lighting boards and integrated infrared transmitter.The lighting boards are simply inserted into the light chambers from behind and are held in place by a press fit.The system is controlled by a KLM 4/16, which is compatible with normal forward-reverse speed controllers (with or without separate brake), cruise control controllers and all sound modules.The lighting functions can be controlled either with our control pad or in numerous other ways, for details please refer to the online manual.This starter set includes a complete lighting system for the Mercedes-Benz Arocs 3348/4151 from TAMIYA and consists of two front lighting boards with wired LEDs for the side indicators, underrun protection and marker lights, as well as a KLM 4/16 light assistant.br>The lighting boards are connected directly to the KLM 4/16 and can also be configured using our Kraftwerk ControlPanel. Brightness, flashing speeds and also the basic functionality (e.g. should the high beam be switched on at the output) can be set separately for each output. Information about this can be foundHighlights & DetailsKLM 4/16 (4 servo inputs, 16 switching outputs, 5 bus outputs) Ready-to-install lighting boardsPlug & Play solution (connect and drive)Compatible with all sound modulesCompatible with all speed controllersCompatible with Tamiya MFUExpandable with a wide variety of lighting boardsExpandable with infrared for trailer lightingCan be adapted to the model down to the smallest detail using a PCNo programming knowledge requiredPC software can be downloaded free of chargeTechnical specificationsPower supply:via receiver power supply (BEC of the speed controller)Max. Power consumption 20mA per device and 20mA per LEDLEDs front (per side):yellow: 1x 3mmwhite: 2x 3mm, 1x 5mmyellow wired: 2x 3mmwhite wired: 1x 3mmUltra-bright high-performance LEDsAdditional outputs front 3 with 180 Ohm resistance eachLEDs rear (per side):red: 1x 3mm, 1x 5mmyellow: 1x 5mmwhite: 1x 3mmUltra-bright high-performance LEDsAdditional outputs rear 2 each with 180 Ohm resistanceScope of deliveryLight assistant KLM 4/16four ready-to-install lighting boards (2x front, 2x rear)

Available immediately, delivery time: 1-4 days

Product number: 11264

€ 219,00 * € 224,90 * (2.62% saved)

Subscriptions

Rear lightbar easy. Roof luminous bar for all FH

1x rear lightbar easy. Dachleucht- bar for all cabs with 7 LEDs. Depending 2x LED yellow (outside) for turn signals, 3x LEDs red for taillight / brake light.

Available immediately, delivery time: 1-4 days

Product number: 9872

€ 59,90 *

Subscriptions

EasyBus Lighting System KLM 4 / 16 TAMIYA MB Arocs 3363

EasyBus lighting system KLM 4/16 for Tamiya Mercedes-Benz Arocs 3363. The lighting system for the TAMIYA Arocs 3363 with the new KLM 4/16, ready-to-install lighting boards and integrated infrared transmitter.The lighting boards are simply inserted into the light chambers from behind and are held in place by a press fit.The system is controlled by a KLM 4/16, which is compatible with normal forward-reverse speed controllers (with or without separate brake), cruise control controllers and all sound modules.The lighting functions can be controlled either with our control pad or in numerous other ways, for details please refer to the online manual.This starter set includes a complete lighting system for the Mercedes-Benz Arocs 3363 from TAMIYA and consists of two front lighting boards with wired LEDs for the side indicators, underrun protection and marker lights, as well as a light assistant KLM 4/16.br>The Lighting boards are connected directly to the KLM 4/16 and can also be configured via this with our Kraftwerk ControlPanel. Brightness, flashing speeds, but also the basic functionality (e.g. should the high beam be switched on at the output) can be set separately for each output. Information about this can be foundHighlights & DetailsKLM 4/16 (4 servo inputs, 16 switching outputs, 5 bus outputs) Ready-to-install lighting boardsPlug & Play solution (connect and drive)Compatible with all sound modulesCompatible with all speed controllersCompatible with Tamiya MFUCan be expanded with a wide variety of lighting boardsCan be expanded with infrared for trailer lightingCan be adapted to the model down to the smallest detail using a PCNo programming knowledge requiredPC software can be downloaded free of chargeTechnical specificationsPower supply:via receiver power supply (BEC of the speed controller)Max. Power consumption 20mA per device and 20mA per LEDLEDs at the front (per side):yellow: 1x 3mmwhite: 2x 3mm, 1x 5mmyellow wired: 2x 3mmwhite wired: 1x 3mmUltra-bright high-performance LEDsAdditional outputs at the front 3 with 180 Ohm resistance eachLEDs at the rear (per side):red: 1x 3mm, 1x 5mmyellow: 1x 5mmwhite: 1x 3mmUltra-bright high-performance LEDsAdditional outputs at the rear 2 each with 180 Ohm resistanceScope of deliveryLight assistant KLM 4/16four ready-to-install lighting boards (2x front, 2x rear)

Available immediately, delivery time: 1-4 days

Product number: 11004

€ 199,00 * € 229,90 * (13.44% saved)

Subscriptions

EasyBus replacement cable 80cm long, 1-sided with post coupling

EasyBus replacement cable 80cm long. 1-sided with post coupling. 1 side open wire ends.

Available immediately, delivery time: 1-4 days

Product number: 12170

€ 2,98 *

Subscriptions

Power plant set with RS1 for Scania 770 S from Tamiya

Set consisting of RS1 and circuit boards for front and rear. Speed controller, lighting system, sound module in one incl. Complete lighting for Scania 770 S from Tamiya. Robust speed controllerThe speed controller can be permanently loaded with 25A and, thanks to the 32kHz control, is also suitable for bell-armature motors. It offers manual transmission support for up to four gears, a clutch function, handbrake, optional inertia simulation and a cruise control function, which does not work like the competition (stick deflection controls acceleration), but like the original: the throttle deflection controls the speed and the cruise control is activated by pressing a button. Pressing the button again or braking deactivates the cruise control.Extraordinary soundKraftwerK is once again setting standards in programmability. While the competition can only use a few sound snippets for the driving sound, KraftwerK can use as many as you like and it works as follows: First, the speed range is defined, e.g. 500 rpm immediately after starting and 2300 rpm when the engine is running out. Then sound snippets are stored for any number of areas and defined with base speed, minimum and maximum. At minimum the sound is faded in at a speed-adjusted level, at it is played at full volume and at a speed of 1:1, and up to maximum it is again adjusted to the speed and finally faded out. The snippets can and should of course overlap, which can create an ultra-realistic sound. In total there are three sound tracks: 2x acceleration and 1x deceleration. The first sound track is the normal driving sound, the second sound track can either be mixed proportionally as a load or switched. The third sound track is the delay sound and is automatically added when you release the joystick. If that's too complicated for you, you'll be pleased to know that 3 high-quality sounds are already included with the module. In the future there will also be a sound library with premium sounds that can be purchased for a few euros and downloaded via the ControlPanel and saved on your own module.Unlimited expandabilityKraftwerK's leading role in the field of RC bus systems is now fully evident in the RS1. The RS6 can be expanded as required via the 1 EasyBus outputs. Lighting boards, switching extensions, servo controls and much more can be controlled via the EasyBus. But the RS1 has one more special gimmick: on the upper side there are four individual sockets that are barely visible and can be used to plug in another module. The first module in this series is the BL8A, an 8A brushless controller designed for hydraulic pumps.Versatile connections / technical dataBattery (6 - 20V)Motor 25A, up to 32kHz, brush and bell-armature motor5 servo inputs or SUMD, IBUS, SBUS, CPPM5 servo outputs6 bus outputs8 switching outputs 500mA2 switching outputs 10AInfrared transmitter (diode included)SpeakerDimensions 63x44x28mmCharacteristics of the drive controllerOperating voltage 6-20VBEC 6V / 3ATimension frequency adjustable up to 32kHZClutch functionHandbrake functionManual transmission supportAdjustable inertia simulationAdjustable cruise controlProtection functions: battery undervoltage, motor short circuit, overtemperatureFunctions for servo outputsProportional functionProportional function directPropFunction switchedTwo positionsThree positionsFifth wheel plateTrailer supports MotorDump truck/tipper MotorRamp/Platform MotorManual transmissionSound featuresUnlimited number of sounds10-15 sounds that can be played simultaneouslyPlay modes: Touch, loop, once, permanent, random, stop pointsFormats: WAV, MP3 Usable sampling rate: All (automatic conversion to 44.100)Volume control: Potentiometer, via channel, via softwareSD card: max.

Available immediately, delivery time: 1-4 days

Product number: 13185

€ 439,80 *

Subscriptions

Power station zone Infrared transmitter diode

Power station zone Infrared transmitter diode 5mm round. For KLM 4 / 16.

Available immediately, delivery time: 1-4 days

Product number: 11286

€ 9,90 *

Subscriptions

Holland taillights. Power plant zone

Holland taillights. (1 pair). Designed for 7,2V voltage. Common plus pole and minus switching for all light functions. Series resistors are integrated. If you would like to replace the original taillights on your model with more original ones, our Holland taillights may be able to help. They consist of three taillight/brake light/indicator combinations and a reversing light or rear fog light and are therefore equipped with twenty LEDs! This article is available as an EasyBus variant or with conventional control. The EasyBus variant can be seen in the photo! The conventional version is designed for minus-switching lighting systems and offers a switching line for indicators, tail light/parking light (upper and lower LEDs light up together) and rear fog light or reversing light.--Holland tail lights WITHOUT EasyBus They consist of three tail light - brake light - indicator combinations and a reversing light or rear fog light and are thus equipped with twenty LEDs!The tail lights measure 50mm in width (dimensions: 50x13mm) and therefore fit on the fenders of the Tamiya models. Caution: When using on a semitrailer/trailer, the mounting holes in the bumper may have to be moved.For voltage: 7,2V.

Available immediately, delivery time: 1-4 days

Product number: 10467

€ 114,89 *

Subscriptions

EasyBus lighting system KLM 4 / 16 TAMIYA Scania R470 and R620

EasyBus lighting system KLM 4/16 for Tamiya Scania R470 and R620. The lighting system for the TAMIYA Scania R470 and R620 with the new KLM 4/16, ready-to-install lighting boards and integrated infrared transmitter. The front lighting boards are simply inserted into the light chambers from behind and are held in place by a press fit. For the rear taillights, the original bars must be removed and a hole drilled for the cable to pass through. The boards are glued into the machined lamp bodies including the supplied dividers. The mentioned dividing grids create the original division into five chambers and at the same time provide mounts for the lamp lenses.The system is controlled by a KLM 4/16, which is compatible with normal forward-reverse speed controllers (with or without separate brake), cruise control controllers and all sound modules.The light functions can be controlled either with our control pad or in numerous other ways, for details please refer to the online manual.This starter set includes a complete lighting system for the Scania R470 and R620 from TAMIYA and consists of two front lighting boards and two rear ones, as well as a KLM 4/16 light assistant.The lighting boards are connected directly to the KLM 4/16 and can also be configured via this with our Kraftwerk ControlPanel. Brightness, flashing speeds, but also the basic functionality (e.g.: should the high beam be switched on at the output) can be set separately for each output. Information about this can be foundHighlights & DetailsKLM 4/16 (4 servo inputs, 16 switching outputs, 5 bus outputs) Ready-to-install lighting boardsPlug & Play solution (connect and drive)Compatible with all sound modulesCompatible with all speed controllersCompatible with Tamiya MFUExpandable with a wide variety of lighting boardsExpandable with infrared for trailer lightingCan be adapted to the model down to the smallest detail via PCNo programming knowledge requiredPC software can be downloaded free of chargeTechnical specificationsPower supply:via receiver power supply (BEC of the speed controller)Max. Power consumption 20mA per device and 20mA per LEDLEDs at the front (per side):yellow: 1x 3mmwhite: 2x 3mm, 2x 5mmUltra-bright high-performance LEDsAdditional outputs at the front 3 with 180 Ohm resistance eachLEDs at the rear (per side):red: 4x SMD 1206yellow: 1x SMD 1206white: 1x SMD 1206Ultra-bright high-performance LEDsAdditional outputs at the rear 1 each with 180 Ohm resistanceScope of deliveryLight assistant KLM 4/16four ready-to-install lighting boards (2x front, 2x rear)

Available immediately, delivery time: 1-4 days

Product number: 11000

€ 230,81 *

Subscriptions

RC Multibus USB interface for the configuration of

RC Multibus USB interface to configure Kraftwerk modules without a light assistant. This article replaces article 11216! With this interface, Kraftwerk's RCMultiBus modules can be configured and tested with and without a receiver. The EasyBus modules can also be connected directly to this interface and configured without a BusMaster (such as KLM 4/16 or RS1). EasyBus systems installed in the model can be connected using the double-sided patch cable provided. The RCMultiBus currently includes EasyBus, IBUS, SBUS, SUMD V3, CPPM and UART.

Available immediately, delivery time: 1-4 days

Product number: 12046

€ 46,05 *

Subscriptions

Holland taillights EasyBus. Power plant zone

Holland taillights EasyBus EasyBus variant Holland taillights. They consist of three taillight - brake light - indicator combinations and a reversing light or rear fog light and are equipped with twenty LEDs! The taillights measure 50mm in width (dimensions: 50x13mm) and therefore fit on the fenders of the Tamiya models. Caution: When using on a semi-trailer/trailer, the mounting holes in the bumper may have to be moved.

Available immediately, delivery time: 1-4 days

Product number: 10447

€ 114,89 *

Subscriptions

1x EasyBus lighting boards for Tamiya MAN 18.540 and

1x EasyBus lighting board for Tamiya MAN 18.540 and TGX 26.540 rear. Suitable for the EasyBus system. The plug & play solution. Scope of delivery:1x lighting board for Tamiya MANs, rear, left1x lighting board for Tamiya MANs, rear, rightPlug & PlayPerfect fit for the rear lights of the Tamiya MANs.With 3-pin plug connection. Integrated series resistors.Connection wires each approx. 60cm long.Power supply comes from the receiver output.The following functions can be controlled with the LIGHT ASSISTANT main module:-Parking light/tail light-Brake light-Reverse light-American tail light-Indicator left/right-Hazard warning light-American indicator-Rear fog light

Available immediately, delivery time: 1-4 days

Product number: 9505

€ 59,80 *

Subscriptions

Rear lightbar EasyBus. Roof luminous bar for all FH

1x EasyBus rear light bar. Roof light bar for all driver's cabs with 7 LEDs. 2x yellow LEDs (outside) for indicators, 3x red LEDs for tail light/brake light. 2 screws and washers are included for attachment to the driver's cab roof. The holders can be swiveled - so the rear light bar can be adjusted after attachment. Series resistors are already installed. The lighting functions are switched directly with the Easybus system. For this, the rear light bar is connected to an EasyBus distributor.

Available immediately, delivery time: 1-4 days

Product number: 9871

€ 59,90 *

Subscriptions

1x KLB 12-20 Expansion Board. The expansion board bi

1x KLB 12-20 expansion board. The expansion board offers the possibility of expanding the light assistant by a further 8 outputs. Plug & Play solution. The module, which is only 15 x 28 mm in size, offers the possibility of expanding the light assistant by a further eight outputs - capable of handling up to 20 mA. It is simply connected to one of the EasyBus outputs of the light assistant and is thus automatically integrated into the system. The outputs of the expansion board offer exactly the same functionality as the outputs of the light assistant. - In addition to some effect lighting, all the usual lighting functions in the original are available: - combined front light (parking light, low beam, high beam, headlight flasher and fog light) - combined rear light (parking light, brake light, rear fog light) - American rear light (parking light, brake light, indicator) - daytime running light with automatic lowering when indicator is activated - cornering light - cornering light - reversing light - indicator, hazard warning light, American indicator - multi-flashing light - running light - rotating light - KnightRider In addition to the basic behavior of the individual outputs, the brightness, the switching on and off speed, as well as the switching on and off duration for flashing functions can also be set. Dimensions: 15x28x13mm Number of switching outputs: 8 Current load capacity per output: 20mA Voltage at the + output: BEC voltage (5-6V)LED series resistor integrated: yes (180 Ohm)Power supply: via bus (BEC of the speed controller)Max. own power consumption: 25mA

Available immediately, delivery time: 1-4 days

Product number: 10113

€ 19,90 *

Subscriptions

1x EasyBus lighting boards for Tamiya MAN 18.540 and

1x EasyBus lighting board for Tamiya MAN 18.540 and TGX 26.540, front. Suitable for the EasyBus system. The plug & play solution. Lighting boards for TAMIYA-MANs!Scope of delivery:1x lighting board for Tamiya MANs, left1x lighting board for Tamiya MANs, rightPlug & PlayPerfect fit for the front of the Tamiya MANs.With 3-pin plug connection. Integrated series resistors.With 3 individually usable additional outputs.Connection wires each approx. 30cm long.Power supply comes from the receiver output.The following functions can be controlled with the LIGHT ASSISTANT main module:-Parking light-Low beam-High beam-Fog light-Flash light-Left/right indicator-Hazard warning light-Xenon effect-Daytime running light-Corner light/cornering light

Available immediately, delivery time: 1-4 days

Product number: 9504

€ 69,79 *

Subscriptions

TAMIYA MB Arocs 3363/3348 front left/right including side indicators

TAMIYA MB Arocs 3363/3348 front left/right including side indicator LEDs. Ready-to-install lighting boards. For Kraftwerk EasyBus system.

Available immediately, delivery time: 1-4 days

Product number: 11407

€ 79,90 *

Subscriptions

EasyBus daytime running light replacement cable 10cm long 1-sided with P

EasyBus daytime running light replacement cable 10cm long 1-sided with post coupling. 1 side open strand ends.

Available immediately, delivery time: 1-4 days

Product number: 12171

€ 2,59 *

Subscriptions

1x KSB2 servo control. For EasyBus- system. To connect

1x KSB2 servo control. For EasyBus system. For connecting up to 2 servos This module expands your EasyBus system with 2 freely adjustable servo outputs. The KSB2 module does not require an additional power supply. Technical data: Dimensions: 28x40x11mm Supply voltage: via the EasyBus Servo outputs: 2 Details: Plug & Play solution 2 additional servo outputs for the EasyBus Adjustable via control panel Proportional functions (e.g. for steering servo) Digital functions (e.g. fifth wheel coupling, ramps or flaps) Center positions, rotation speeds and directions of rotation adjustable No programming knowledge required PC software can be downloaded free of charge The following functions can be implemented with this module: - Proportional function - Proportional function switched - Two positions - Two positions center position - Actuator - Hydraulic simulation - Fifth wheel plate - Trailer supports - Trough - Windscreen wiper - Searchlight

Available immediately, delivery time: 1-4 days

Product number: 9250

€ 38,90 *

Subscriptions

1x KMB1 - 10A speed controller for Easy-Bus system for Nebe

1x KMB1 - 10A speed controller for Easy-Bus system for auxiliary drives. The KMB 1-10A has a motor output with a load of 10A. It is intended for auxiliary drives and, thanks to the two connections for limit switches, is also ideal for spindle drives. Dimensions 34x23x12mm

Available immediately, delivery time: 1-4 days

Product number: 9251

€ 39,89 *

Subscriptions

EasyBus replacement LED with 60cm cable. LED 3mm yellow with 60cm

EasyBus replacement LED with 60cm cable. LED 3mm clear, glowing yellow with 60cm strands and open strand ends. Suitable for side marker lights and lighting boards.

Available immediately, delivery time: 1-4 days

Product number: 12461

€ 4,30 *

Subscriptions

Scania front lighting set. Includes a pair of reflectors

Scania front lighting set. Contains a pair of reflectors including pre-assembled circuit board. For the front of the Scania 770 S from Tamiya

Available immediately, delivery time: 1-4 days

Product number: 13187

€ 34,90 *

Subscriptions

1x BUS - distributor with 3,5mm jack. With this distributor la

1x BUS distributor with 3,5mm jack. With this distributor, the EasyBus outputs can be plugged into the trailer via a jack socket. Plug & Play solution.1x BUS distributor with 3,5mm jack. With this distributor, the EasyBus outputs can be plugged into the trailer via a jack socket. Plug & Play solution.

Available immediately, delivery time: 1-4 days

Product number: 9256

€ 24,89 *

Subscriptions

Scania 770S roof lighting set. Includes KLB-12 roof LEDs

Scania 770S roof lighting set. Includes KLB-12 roof, 5 wired LEDs for roof lamp bracket, 2 wired LEDs for sun visor and roof reflector including circuit board.

Ready to ship in 30 days, delivery time 1-4 days

Product number: 13186

€ 89,90 *

Subscriptions

EasyBus replacement LED with 15cm cable. LED 3mm clear, white light

EasyBus replacement LED with 15cm cable. 3mm clear LED, white light with 15cm wires and open wire ends. Suitable for side marker lights and lighting boards.

Available immediately, delivery time: 1-4 days

Product number: 13167

€ 3,90 *

Subscriptions

1x KSB4 servo control. For EasyBus- system. To connect

1x KSB4 servo control. For EasyBus system. For connecting up to 4 servos. This module expands your EasyBus system by 4 freely adjustable servo outputs. The KSB4 module must also be provided with a power supply. The VCC cable is either routed to a free receiver output or connected to an external battery.Technical data:Dimensions: 24x20x6mmSupply voltage: 4-5 cells NiMH (max. 8V)Servo outputs: 4Details:Plug & Play solutionFour additional servo outputs for the EasyBusAdjustable via control panelProportional functions (e.g. for steering servo)Digital functions (e.g. fifth wheel, ramp or flaps)Center positions, rotation speeds and rotation directions adjustableNo programming knowledge requiredPC - software can be downloaded free of chargeThe following functions can be implemented with this module:-Proportional function-Proportional function switched-Two positions-Two positions center position-Actuator-Hydraulic simulation-Fifth wheel plate-Trailer supports-Trough-Windscreen wiper-Searchlight

Available immediately, delivery time: 1-4 days

Product number: 9249

€ 38,90 *

Subscriptions

TAMIYA MB Arocs 3363 rear left / right. incl. series resistors.

TAMIYA MB Arocs 3363 rear left / right. incl. series resistors. Ready to install lighting boards. For power plant EasyBus system. NOT for Arocs 3348 rear dumpers!

Available immediately, delivery time: 1-4 days

Product number: 11408

€ 59,80 *

Subscriptions

Power plant board TAMIYA Scania R470 and R620 front

TAMIYA Scania R470 and R620 front-ready lighting boards. For power plant EasyBus system.

Available immediately, delivery time: 1-4 days

Product number: 11024

€ 69,79 *

Subscriptions

TAMIYA MB Arocs 3348 rear left/right. including series resistors

TAMIYA MB Arocs 3348 rear left/right including series resistors. Ready-to-install lighting boards. For Kraftwerk EasyBus system. These boards only fit the AROCS 3348 from Tamiya.

Available immediately, delivery time: 1-4 days

Product number: 12342

€ 59,80 *

Subscriptions

EasyBus lighting system KLM 4 / 16 TAMIYA MB Actros 1851

EasyBus lighting system KLM 4/16 for Tamiya Mercedes-Benz Actros 1851 The lighting system for the TAMIYA MB Actros 1851 with the new KLM 4/16, ready-to-install lighting boards and integrated infrared transmitter.The lighting boards are simply inserted into the light chambers from behind and are held in place by a press fit.The system is controlled by a KLM 4/16, which is compatible with normal forward-reverse speed controllers (with or without separate brake), cruise control controllers and all sound modules.The lighting functions can be controlled either with our control pad or in numerous other ways, for details please refer to the online manual.This starter set includes a complete lighting system for the Actros 1851 from TAMIYA and consists of two front lighting boards with wired LEDs for the side indicators, underrun protection and marker lights, as well as a light assistant KLM 4/16.The lighting boards are connected directly to the KLM 4/16 and can also be configured using our Kraftwerk ControlPanel. Brightness, flashing speeds and also basic functionality (e.g. should the high beam be switched on at the output) can be set separately for each output. Information about this can be foundHighlights & DetailsKLM 4/16 (4 servo inputs, 16 switching outputs, 5 bus outputs) Ready-to-install lighting boardsPlug & Play solution (connect and drive)Compatible with all sound modulesCompatible with all speed controllersCompatible with Tamiya MFUCan be expanded with a wide variety of lighting boardsCan be expanded with infrared for trailer lightingCan be adapted to the model down to the smallest detail using a PCNo programming knowledge requiredPC software can be downloaded free of chargeTechnical specificationsPower supply:via receiver power supply (BEC of the speed controller)Max. Power consumption 20mA per device and 20mA per LEDLEDs at the front (per side):1 x 3mm yellow1 x 3mm white2 x 5mm white2x 3mm white wired1x 3mm yellow wiredUltra-bright high-performance LEDsAdditional outputs at the front 3 with 180 Ohm resistance eachLEDs at the rear (per side):1x 5mm red1x 5mm yellow1x 3mm white1x 3mm redUltra-bright high-performance LEDsAdditional outputs at the rear 1 each with 180 Ohm resistanceScope of deliveryLight assistant KLM 4/16Four ready-to-install lighting boards (2x front, 2x rear)

Available immediately, delivery time: 1-4 days

Product number: 11002

€ 234,89 *

Subscriptions

EasyBus lighting boards for Tamiya SCANIA 770S front

1x EasyBus lighting board for Tamiya SCANIA 770S and 770S SLT, front. Suitable for the EasyBus system. The plug & play solution. Lighting boards for TAMIYA SCANIAs 770S and SLT Scope of delivery:1x lighting board for Tamiya SCANIA 770S, left1x lighting board for Tamiya SCANIA 770S, rightPlug & PlayPerfect fit for the front of the Tamiya Scanias.With 3-pin plug connection. Integrated series resistors. With 3 individually usable additional outputs. Connection wires each approx. 30cm long. Power supply from the receiver output. The following functions can be controlled with the main module LIGHT ASSISTANT: - Parking light - Low beam - High beam - Fog light - Headlight flasher - Left/right indicator with wiping effect - Hazard warning lights - Xenon effect - Daytime running lights (LEDs) - Cornering light and turning light - 3 freely programmable additional outputs (plug-in)

Available immediately, delivery time: 1-4 days

Product number: 13203

€ 99,79 *

Subscriptions

KLM 4 / 16 light assistant SET incl.LED cable harnesses

1x KLM 4/16 light assistant set incl. LED wiring harnesses. The lighting assistant is the core component of a lighting system that can be expanded as required. Incl. Transmitting diode. Plug & Play solution. Core component of the lighting system, compatible with all sound modules, speed controllers and the Tamiya MFU-xx. The EasyBus lighting systems are equipped with different lighting boards, IR trailer lighting, etc. expandable.Includes LED wiring harnesses (for 12V!) for front and rear lighting.The PC software can be downloaded free of charge. No programming knowledge is required. The control can be customized down to the smallest detail. Technical data: - Dimensions 51x36x13 mm - 4 inputs (steering, throttle, channel 1, channel 2) - 2 servo outputs (steering servo, speed controller) - 5 bus outputs (for expansion modules) - 16 switching outputs with max. 500mA, freely configurable-1x USB socket (Micro-USB, for configuration)From April 2018 incl. Transmitter diodeWe are of course happy to configure the lighting system according to your ideas and also save them.The KLM 4/16 light assistant is the further development of the KLM 4/12-500. Compact design, easy operation and compatibility with the most common systems on the market are its main strengths. It is compatible with standard forward-reverse speed controllers (with or without a separate brake), with the cruise control controllers from Servonaut and all sound modules. The light functions can be controlled in a variety of ways; please refer to the manual for details. The module, which is only 52 x 36 x 13 mm in size, offers eight high-current outputs (500 mA each and eight switching outputs with integrated series resistors), four adjustable servo outputs, an infrared output, a USB socket that is only required for configuration and five bus outputs, via which the system can be expanded as required with additional switching, servo or motor functions. Standard assignment of the outputs:-Output 1 & 2: parking light & high beam & headlight flasher-Output 3 & 4: dipped beam-Output 5: left indicator-Output 6: right indicator-Output 7 & 8: tail light & brake light-Output 9: rear fog light-Output 10: reversing light-Output 11 & 12: speed camera-It is possible to select the behavior of each individual output completely independently and freely via PC and to configure it on a percentage basis. In addition to some effect lighting, you can choose from all the usual lighting functions in the original: -- combined front light (parking light, low beam, high beam, headlight flasher and fog light) -- combined rear light (parking light, brake light, -- American rear light (parking light, brake light, indicator) -- daytime running light with automatic lowering when the indicator is activated -- cornering light -- curve light -- reversing light -- indicator, hazard warning light, American indicator -- multi-flashing light -- running light -- rotating light -- KnightRider In addition to the basic behavior of the individual outputs, the brightness, the switching on and off speed, and the switching on and off duration for the flashing functions can also be set. How easy this is can be tested in advance using the demo mode of the free PC software ControlPanel. The module is connected to four channels of the receiver. In addition to gas and steering, two channels (K1 and K2) are used to control the lighting. Please refer to the manual for the different variants! During development, special attention was paid to ease of use. You do not need any electronic experience to use this system! You will find all the information you need in the included quick start guide!

Ready to ship in 14 days, delivery time 1-4 days

Product number: 11174

€ 164,99 * € 172,28 * (4.23% saved)

Subscriptions

RC Multibus USB-Interface for the configuration of Kraftwer

RC Multibus USB interface to be able to configure power plant modules without a light assistant. With jack plug connection.

Available immediately, delivery time: 1-4 days

Product number: 12044

€ 56,31 *

Subscriptions

EasyBus lighting boards for Tamiya SCANIA 770S rear

1x EasyBus lighting board for Tamiya SCANIA 770S and 770S SLT, rear. Suitable for the EasyBus system. The plug & play solution. Suitable for the Tamiya SCANIA 770S and 770S SLT.Scope of delivery:1x lighting board for Tamiya SCANIA 770S, rear, left1x lighting board for Tamiya SCANIA 770S, rear, rightPlug & PlayPerfect fit for the rear lights of the Tamiya SCANIAs.With 3-pin plug connection. Integrated series resistors.Connection wires each approx. 60cm long.Power supply comes from the receiver output.The following functions can be controlled with the LIGHT ASSISTANT main module:-Parking light/tail light-Brake light-Reverse light-Left/right indicator (wiper indicator)-Hazard indicator-American indicator-Rear fog light-3 freely programmable additional outputs (pluggable)

Available immediately, delivery time: 1-4 days

Product number: 13204

€ 79,80 *

Subscriptions

1x EasyBus lighting boards for Tamiya ACTROS 1851

1x EasyBus lighting board for Tamiya ACTROS 1851 GigaSpace, rear. Suitable for the EasyBus system. The plug & play solution. Lighting boards for TAMIYA ACTROS1851!Scope of delivery:1x lighting board for Tamiya ACTROS, rear, left1x lighting board for Tamiya ACTROS, rear, rightPlug & PlayPerfect fit for the rear lights of the Tamiya ACTROS.With 3-pin plug connection. Integrated series resistors.Connection wires each approx. 60cm long.Power supply comes from the receiver output.These functions can be controlled with the LIGHT ASSISTANT main module:-Parking light/tail light-Brake light-Reversing light-American tail light-Indicator left/right-Hazard warning light-American indicator-Rear fog light

Ready to ship in 14 days, delivery time 1-4 days

Product number: 9508

€ 59,80 *

Subscriptions

Power plant board TAMIYA Scania R470 and R620 rear

TAMIYA Scania R470 and R620 rear-ready lighting boards. For power plant EasyBus system.

Available immediately, delivery time: 1-4 days

Product number: 11022

€ 59,80 *

Subscriptions

KraftweK control pad RS1. Control pad for all transmitters for RS1

KraftweK control pad RS1. Control pad for all transmitters for use with Kraftwerk RS1. The pad is connected to a free proportional channel in the transmitter and behaves like a normal joystick, i.e. no complex transmission signals are used as with most multiswitches, which means that it should be usable in any remote control transmitter.The RS1 control pad switches all light functions, the trailer supports, the tipping trough, the fifth wheel coupling and 11 additional functions (e.g. a rotating light), the gear shift and 2 servos. There is also a button for everything on and everything off if you need to do something quickly!Dimensions: 78x33mmThe pad is compatible with all remote control transmitters.It is important that the selected channel is a proportional channel, i.e. a servo on the corresponding receiver output must be able to be controlled continuously. (Switching channels are unsuitable!!!)The channel should ideally be free, i.e. no other control device (joystick, linear regulator, ...) should be connected. Since new transmitters often no longer have any extension channels, an occupied channel can also be used in an emergency, but this must not be in use and must always be in the middle position (otherwise the functions will not switch).Technical data:Power supply: via the channel in the remote control transmitterMax. power consumption: 20mANumber of buttons: 12Speed controller supported: RS1Sound module supported: RS1Remote control systems supported: all (learning mode required) Long press: approx. 0,5 sec.Dimensions: 78x33mm

Available immediately, delivery time: 1-4 days

Product number: 13180

€ 74,90 *

Subscriptions

Kraftwerk-Zone infrared transmitter diode 5mm round. For GRAVEL.

Available immediately, delivery time: 1-4 days

Product number: 11348

€ 9,90 *

Subscriptions

KLB 12-roof expansion board with 12 outputs

KLB 12-roof expansion board. The expansion board offers the following options: 8 light functions, 4x 500mA outputs, RGB output, servo output, bus output. Plug & Play solution. Technical dataDimensions 23 x 31 x 13mmNumber of switching outputs: 12Current load capacity of the outputs: 500mA eachVoltage at the plus output: BEC voltage (5-6V)LED series resistor integrated: on 8 outputsPower supply: via bus, (BEC of the speed controller)Max. current consumption: 25mAWith the module, which is only 23 x 31mm, the bus system can be expanded by a further twelve outputs. Eight have integrated series resistors, the top four outputs can be loaded with up to 500mA. It is simply connected to one of the EasyBus outputs of the light assistant and is thus automatically integrated into the system. The outputs of the expansion board offer exactly the same functionality as RS1, KLM & Co. In addition to some effect lighting, you can choose from all the usual lighting functions in the original and more:Combined front light (parking light, low beam, high beam, headlight flasher and fog light)Combined rear light (parking light, brake light, rear fog light)American rear light (parking light, brake light, indicator)Daytime running light with automatic lowering when indicator is activatedCornering lightCorner lightReversing lightIndicator, hazard lights, American indicatorMulti-flashing light, strobe lightRunning lightRevolving lightKnightRiderIn addition to the basic behavior of the individual outputs, the brightness, the switching on and off speed, and the switching on and off duration for flashing functions can also be set.Scope of delivery1x KLB 12 - roof expansion board

Available immediately, delivery time: 1-4 days

Product number: 13165

€ 49,90 *

Subscriptions

1x EasyBus Lighting Boards for Tamiya Mercedes 1838

1x EasyBus lighting board for Tamiya Mercedes 1838 and 1850L. Suitable for the EasyBus system. The plug & play solution. 2 ready-to-install boards and 2 light chamber dividers.

No longer available

Product number: 10799

€ 59,80 *

Subscriptions

Details

Power station board TAMIYA Mercedes 1838 and 1850L front

TAMIYA Mercedes 1838 and 1850L front-ready lighting boards. For power plant EasyBus system.

Available immediately, delivery time: 1-4 days

Product number: 11023

€ 59,80 *

Subscriptions

PAGE