1x relay reversing switch with end position shutdown. Failsafe function. For motor polarity reversal with end position detection. Switching capacity max. 10A, 1-40V. Features: - programmable switch-on point - connections for two end position switches, module stops the motor as soon as the end position is reached - negligible power consumption - possible switching capacity per switch 10 A / 1-40 Volt - screw connections - failsafe - dimensions 43 x 34 x 21 mm - weight 40 g with Graupner servo cable When connected to a free channel on the joystick, the connected motor is in the middle position. Can of course be operated with a free channel on the joystick or an ON/OFF/ON switch on the transmitter. Lever up: the motor turns in one direction Lever down: the motor turns in the other direction Lever in the middle position: the motor stands still. There is a practical holder for this module: item 11956.

1x side-correct chain mixer. This mixer allows you to control any tracked vehicle with 2 forward/backward controllers using a joystick. In contrast to the simple V-mixer, this mixer controls both drive motors in a side-correct manner. It therefore allows you to control any tracked vehicle with two forward/backward controllers using a simple joystick. This mixer is also ideal for operating boats with multiple screw drives. Whether you have 2 or more screws, this mixer allows you to perform turning maneuvers much more tightly and precisely. Suitable for both forward/backward and pure forward drives. Features: 2x receiver input (throttle & steering) and 2x output to the controller (motor left & motor right) programmable zero point programmable mixing of 20-100% 2 modes selectable: side-correct and V-mixer Dimensions 34x34x5 mm Weight 15g with cables

1x speed controller AS-12/35RW Truck EVO III. 100% forward, 100% reverse. Max. 35A. With BEC max. 3A / short 5A. 18kHz clock speed! 6-18V input voltage. 5-14 cells NiMH or 2-4 LiPos. Dimensions: 36x33x11mm. 33gr. Version without cruise control! Max. current: 35A (50A short). Autosetup, failsafe, LED monitor, LiPo detection, undervoltage protection, intelligent soft polarity reversal, 2 different handbrake modes. Overtemperature shutdown. Outputs for brake and reversing light with 1A each. Handbrake The AS12-35RW Truck Evo III has two different handbrake modes. In normal mode (green LED flashes) the brake slowly switches on in the zero position and ensures that the model stops but does not. This mode is recommended for most applications, especially for street trucks. For crawlers and four-wheel drive trucks that like to stop on a slope, it is recommended to select the brake mode (red LED flashes). In this mode, the brakes are applied very quickly and thus prevent the model from rolling away on the slope. But be careful: This mode can brake a model at full speed very quickly! Performance features: - 5-14 cells / 2-4 Lipos / 12 Volt lead (with Lipo monitoring 3,4V per cell) - Automatic cell count detection in Lipo mode (at approx. 3,4 volts per cell), the maximum power is limited to 25% and the controller signals that the battery is empty by jerking the motor) - 35 A continuous, 50 A short-term - Switching BEC up to 14 cells / 4s Lipo. 3A continuous up to 5A short-term - two different braking modes can be programmed (street truck / crawler). - Lipo monitoring can be switched on / off - Overtemperature shutdown, if the controller gets too hot it regulates back to max. 25% power. - Full HF 18 kHz output stage over the entire control range. NO motor whistling and extremely sensitive control. - Motor-friendly polarity reversal through speed-dependent polarity reversal time with brake. The braking time is calculated using an algorithm. (In the lower speed range the polarity is reversed immediately; at high speeds the controller brakes the motor gently so that the batteries and motor are protected from high current peaks.) - Handbrake function. When the throttle is at 0, the vehicle is first braked gently, then the handbrake is pulled.- Perfect failsafe (receiver signal is constantly checked) LED shows when the reception signal is lost.- Motor beep acknowledgement (for programming and for the OK message when connecting the battery).- Start-up protection (the controller only starts operating when the throttle is at 0. This prevents the motor from accidentally starting). If there is no RC signal, the vehicle stops.- Super-sensitive logarithmic control behavior (new evaluation system.- Two outputs for brake and reversing lights, each with a load of 1A, switch to ground.- 2,5 sqmm highly flexible connection cableDimensions 36 x 33 x 11 mmWeight 33 g

1x 2-channel switch (2x memory). 2 consumers can be switched on/off separately with 1 RC channel. Switching capacity per output max. 2A/ max. 20V. e.g. for lighting, headlights, fog horn, etc. Works with a free proportional channel or a 3-position switch on the transmitter. The 2-channel switch is particularly suitable for complex lighting with LEDs or bulbs, as 2 different functions can be operated independently of one another with just one channel. The RC transmitter does not need to be changed. Performance features: 2 separately and independently switchable switching functions with just one RC channel. Parallel operation on the servo is possible Negligible power consumption Possible switching capacity per switch 2 A / 0-20 Volt 2 powerful SMD-FETs Dimensions 26 mm x 11 mm x 5 mm Weight 9 g with cables Operation: In the following example, the module is connected to a channel with a vertical joystick. Channel 1: Move the joystick up and back to the 0 position. Channel 1 is switched on. Channel 2: Move the joystick down and back to the 0 position. Channel 2 is switched on. To switch off the respective channel, repeat the process!

1x AS-12/6RW Easy speed controller with cables. 100% forward, 100% reverse. Max. 6A. Without BEC. 18kHz clocking! 6-15V input voltage. 5-12 cells NiMH or 2-3 LiPos. Dimensions: 20x17x5mm. 6gr. Version without cruise control! Max. current: 6A (10A short). Failsafe, no LiPo monitoring. Intelligent soft polarity reversal. Performance features: - 5-12 cells / 2-3 LiPos / 12 Volt lead - 6 A continuous, 10 A short-term - Full HF 18 kHz output stage over the entire control range. NO motor whistling and extremely sensitive control. - Motor-friendly polarity reversal thanks to speed-dependent polarity reversal time. Speed ​​range is immediately reversed (at high speeds the controller brakes the motor gently so that the battery and motor are protected from high current peaks.) - perfect failsafe (receiver signal is constantly checked) LED shows when the reception signal is lost. - Motor beep acknowledgement (for programming and for the OK message when connecting the battery). - Start-up protection (the controller only starts operating when the throttle stick is at 0. This prevents the motor from starting accidentally). If there is no RC signal, the vehicle stops. - super-sensitive logarithmic control behavior (new evaluation system. - 2,5 sqmm highly flexible connection cable Dimensions 20 x 17 x 5 mm Weight 6 g

1x 2-channel switch (2x 10A) / 2 relays. 2 consumers can be switched on/off separately with 1 RC channel. Switching capacity per output max. 10A each/ max. 40V. e.g. for lighting, headlights, fog horn, etc. Works with a free proportional channel or a 3-position switch on the transmitter. The 2-channel switch is particularly suitable for complex lighting with LEDs or bulbs, as 2 different functions can be switched independently of each other with just one channel. The RC transmitter does not need to be changed. Features: 2x separate SWITCH function with just one RC channel Switchable memory function for each function can be switched on via DIP. Parallel operation on the servo possibleNegligible power consumptionPossible switching capacity per switch 10A / 0-40 Volt2 relay levels with changeover contactsScrew connectionsLED function controlOperating voltage: 4,8-6VDimensions 40mm x 34mm x 21mmWeight 40g with servo cableOperation:In the following example, the module is connected to a channel withvertical control stick.Channel 1: Move the control stick up and hold itChannel 1 is switched on. (Touch function) Channel 2: Move the control stick down and hold itChannel 2 is switched on. (Touch function)To switch off the respective channel, move the control stick to the neutral position.When the MEMORY function is switched on, the channel remains switched on until the control stick is AGAIN moved to the same position.There is a practical holder for this module: Article 11956.

1x light module Truck-Profi2. Control for indicators and 3 light switching functions. Steering servo signal is looped through. Outputs 2-18V, 2x 2A, 1x 3A load current. The Truck-Profi II lighting module is perfect for anyone who wants to light up their vehicle in a simple way without much effort. The Truck-Profi II is connected parallel to the steering servo and to a free channel and takes over the indicator control of your vehicle. You can use the second channel to switch on any three additional functions such as (horn, fog lights, ...) and the hazard lights. TIP: Together with the AS12-35RW TRUCK EVO III you also have a fully automatic brake and reversing light! -Features: --Flashes automatically when steering -Programmable: Adjustable at what steering angle the indicator starts -5 functions can be switched via switching channel (one is the hazard light)

1x rear and brake light module for parallel operation on a speed controller. Suitable for light bulbs and LEDs. Switching capacity per output max. 2A/max. 20V - 2 separate independent outputs - Parallel operation on the speed controller (with Y-cable, not included) - Light bulbs or LEDs - both possible (suitable series resistors must be installed for LEDs!) - Negligible power consumption - Possible switching capacity per switch 2 A / 0-20 Volt - 2 powerful SMD FETs - Brake light afterglow time: approx. 1 sec. - With highly flexible silicone cable - Dimensions 26mm x 11mm x 5 mm - Weight 7 g with cables

1x 4-channel switch (4x memory). 4 consumers can be switched on/off separately with 1 RC channel. Switching capacity per output max. 2A/ max. 20V. e.g. for lighting, headlights, fog horn, etc. Works with a free proportional channel or a 3-position switch on the transmitter. The 4-channel switch is particularly suitable for complex lighting with LEDs or bulbs, as 4 different functions can be operated independently of one another with just one channel. The RC transmitter does not need to be changed. Performance features: 4 separately and independently switchable switching functions with just one RC channel. Parallel operation on the servo is possible Negligible power consumption Possible switching capacity per switch 2 A / 0-20 Volt 4 powerful SMD-FETs Dimensions 36 mm x 18 mm x 5 mm Weight 11 g with cables Operation: In the following example, the module is connected to a channel with a vertical joystick. Channel 1: briefly move the joystick up and back to the 0 position. Channel 1 is switched on. Channel 2: briefly move the joystick down and back to the 0 position. Channel 2 is switched on. Channel 3: Move the joystick down for more than 2 seconds and return it to the 0 position. Channel 3 is switched on. Channel 4: Move the joystick up for more than 2 seconds and return it to the 0 position. Channel 4 is switched on. To switch off the respective channel, repeat the process!

1x 2-channel switch (2x momentary). 2 consumers can be switched on/off separately with 1 RC channel. Switching capacity per output max. 2A/ max. 20V. e.g. for lighting, headlights, fog horn, etc. Works with a free proportional channel or a 3-position switch on the transmitter. The 2-channel switch is particularly suitable for complex lighting with LEDs or bulbs, as 2 different functions can be operated independently of one another with just one channel. The RC transmitter does not need to be changed. Features: 2 separately and independently operated TAST functions with just one RC channel. Parallel operation on the servo is possible Negligible power consumption Possible switching capacity per switch 2 A / 0-20 Volt 2 powerful SMD-FETs Dimensions 26mm x 11mm x 5 mm Weight 7 g with cables Operation: In the following example, the module is connected to a channel with a vertical joystick. Channel 1 : Move the joystick up and hold it Channel 1 is switched on. Channel 2 : Move the joystick down and hold it Channel 2 is switched on. To switch off the respective channel, bring the control stick into the neutral position.

1x 2-channel switch (1x push button/1x switch) 2 consumers can be switched on/off separately with 1 RC channel. Switching capacity per output max. 2A/ max. 20V. e.g. for lighting, headlights, fog horn, etc. Works with a free proportional channel or a 3-position switch on the transmitter. The 2-channel switch is particularly suitable for complex lighting with LEDs or bulbs, as 2 different functions can be carried out independently of one another with just one channel. The RC transmitter does not need to be changed. Features: 1x BUTTON functions and 1x SWITCH function with just one RC channel. Parallel operation on the servo possible Negligible power consumption Possible switching capacity per switch 2 A / 0-20 Volt 2 powerful SMD-FETs Dimensions 26mm x 11mm x 5 mm Weight 7 g with cables Operation: In the following example, the module is connected to a channel with a vertical joystick. Channel 1: Move the joystick up and hold it Channel 1 is switched on. Channel 2: Move the joystick down and release it Channel 2 is switched on. To To switch off the respective channel, move the joystick to the neutral position. For the switching function, move the joystick back to the switching position and release it again.

Servo holder (standing), black for standard servos. Material: PET, very stable. Maximum size of the servo to be attached (not included): 42x21x29mm.

1x speed controller AS-12/35RW Truck EVO III. 100% forward, 100% reverse. Max. 35A. With BEC max. 3A / short 5A. 18kHz clock speed! 6-18V input voltage. 5-14 cells NiMH or 2-4 LiPos. WITH CRUISE CONTROL! Version with cruise control! Dimensions: 36x33x11mm. Weight: 33gr. Max. current: 35A (50A short). Autosetup, failsafe, LED monitor, Lipo detection, undervoltage protection, intelligent soft polarity reversal, 2 different handbrake modes. Overtemperature shutdown. Outputs for brake and reversing light with 1A each. Handbrake The AS12-35RW Truck Evo III has two different handbrake modes. In normal mode (green LED flashes) the brake slowly switches on in the zero position and ensures that the model comes to a stop but does not... This mode is recommended for most applications, particularly for street trucks. For crawlers and four-wheel drive trucks that like to stop on a slope, it is recommended to select brake mode (red LED flashes). In this mode, the brake kicks in very quickly and thus prevents the model from rolling away on the slope. But be careful: This mode can slow a model down very quickly at full speed! Performance features: - 5-14 cells / 2-4 Lipos / 12 Volt lead (with Lipo monitoring 3,4V per cell) - Automatic cell count detection in Lipo mode (at approx. 3,4 volts per cell) the maximum power is limited to 25% and the controller signals that the battery is empty by jerking the motor) - 35 A continuous, 50 A short-term - Switching BEC up to 14 cells/4s Lipo. 3A continuous up to 5A short-term - two different braking modes can be programmed (street truck / crawler). - Lipo monitoring can be switched on / off - Overtemperature shutdown, if the controller gets too hot it regulates back to max. 25% power. - Full HF 18 kHz output stage over the entire control range. NO motor whistling and extremely sensitive control. - Motor-friendly polarity reversal through speed-dependent polarity reversal time with brake. The braking time is calculated using an algorithm. (In the lower speed range the polarity is reversed immediately; at high speeds the controller brakes the motor gently so that the batteries and motor are protected from high current peaks.) - Handbrake function. When the throttle is at 0, the vehicle is first braked gently, then the handbrake is pulled.- Perfect failsafe (receiver signal is constantly checked) LED shows when the reception signal is lost.- Motor beep acknowledgement (for programming and for the OK message when connecting the battery).- Start-up protection (the controller only starts operating when the throttle is at 0. This prevents the motor from accidentally starting). If there is no RC signal, the vehicle stops.- Super-sensitive logarithmic control behavior (new evaluation system.- Two outputs for brake and reversing lights, each with a load of 1A, switch to ground.- 2,5 sqmm highly flexible connection cableDimensions 36 x 33 x 11 mmWeight 33 g

Holder for relay channel switch. Material: PETG, black, very stable. Suitable for detachable attachment of items 11250 and 9856.

1x AS-12/15RW LiPo speed controller with cables. 100% forward, 100% reverse. Max. 15A. With BEC 2A max. 18kHz clock speed! 6-15V input voltage. 5-12 cells NiMH or 2-3 LiPos. Dimensions: 31x26x7mm. 20gr. Small forward/backward controller for scale models. Suitable for example for Dunker, Bühler or small speed motors in smaller models. This controller is designed exclusively for brush motors, it is not suitable for BL motors! Performance features: 5-12 cells NiCd NiMh / 6 or 12 volt lead / 2-3 S Lipo with automatic cell count detection and undervoltage protection. Lipo undervoltage protection. At around 3,3 volts per cell, the maximum power is limited to 25% and the controller gives stuttering throttle - basically only short, quick throttle pulses. This lets you know it's time to go back.Optical control of the LiPo mode .... the controller shows via LED whether the LiPo protection is active.15 A continuous 20 A short-termSynchronous output stage for full power when driving forward and backwardHigh-performance BEC up to 12 cells / 2 A maxOptional power limitation when reversing to 50% programmableSilent driving with high switching frequency (18KHz) over the entire speed range. The motor is controlled completely silently - there is no whistling or beeping of the motor. Only the mechanical noises of the drive can be heard.Fast motor-friendly polarity reversal: When reversing from forward to reverse, the controller brakes the motor fully automatically and as quickly as possible, and then immediately accelerates in the opposite direction. This controller does NOT have a proportional brake, as is usual with RC car controllers. The full stick travel is therefore available for proportional forward and reverse control. Close to the zero point, there is hardly any noticeable delay in reversing the polarity. This makes it possible to reverse the polarity of the motor as quickly as possible.Perfect failsafe (receiver signal is constantly checked) LED indicates when the reception signal is lost.Motor beep acknowledgement (for the setup function and for the OK messages when connecting the battery)Start-up protection (the controller only starts operating when the throttle stick is at 0. This prevents the motor from accidentally starting)Super-sensitive control behavior 10-bit resolution. 8 bit is standard for most commercially available controllers. This means that the motor can be controlled extremely sensitively. The resolution of the control is therefore 4 times higher.Protection against splash water through protective coating and shrink tubing.1 sqmm highly flexible connection cableDimensions 31 x 26 x 7 mmWeight approx. 20g

Servo holder (lying), black for standard servos. Material: PET, very stable. For servos with a maximum length of 42mm.

1x AS-12/15RW BEC easy speed controller with cables. 100% forward, 100% reverse. Max. 15A. With BEC 1A max. 18kHz clock speed! 6-15V input voltage. 5-12 cells NiMH or 2-3 LiPos. Dimensions: 31x26x7mm. 18g. Small forward/backward controller with EASY technology. This means that the controller does not have to be set to the respective RC system. Simply plug it in and off you go. The controller learns the necessary settings independently. Suitable for example for Dunker, Bühler or small speed motors in smaller models. This controller is designed exclusively for brush motors; it does not work with BL motors. Performance features: 5-12 cells / 6 or 12 volt lead / 2-3 S Lipo (without Lipo monitoring) 15 amp continuous 20 amp short-term Synchronous output stage for full power when driving forwards and backwards 100% forward/100% reverse High-performance BEC up to 12 cells / 1 amp max Variable switching frequency for silent driving with high switching frequency (18 kHz) in the lower speed range. In order to keep the efficiency of the controller high, the clock frequency is automatically reduced in higher speed ranges Fast polarity reversal that is gentle on the motor: When reversing the polarity from forward to reverse, the controller brakes the motor fully automatically and as quickly as possible and then immediately accelerates in the opposite direction. This controller does NOT have a proportional brake like those found on RC car controllers. The full stick travel is therefore available for proportional forward and reverse control. Close to the zero point, there is therefore hardly any noticeable polarity reversal delay. Microprocessor controlled with watchdog Perfect failsafe (receiver signal is constantly checked) LED indicates when the reception signal is lost Motor beep acknowledgement (for programming and for the OK message when connecting the battery) Start-up protection (the controller only starts operating when the throttle stick is at 0. This prevents the motor from accidentally starting) Super-sensitive control behavior (new evaluation system) Protection against splash water through protective coating and shrink tubing. 1 sqmm highly flexible connection cable Dimensions 31 x 26 x 7 mm Weight approx. 18g

1x Power S-BEC, BEC module 5,5V 3A. Input voltage 6-25V, output: 5,5V 3A continuous current. 26x13x8mm, 11gr. This BEC module is consistently developed with the best components we could get. This leads to an extremely high level of efficiency - which means that even with a continuous load of 3 amps, the module hardly gets warm. Not even if the 25 volt max input voltage is exhausted. The module is protected against water damage with two layers of special protective varnish. Technical data: Input voltage 6-25V DC 2-6 cells Lipo or 5-16 cells NiMH / NiCd battery or 12 volt lead Output voltage 5,5 volts 3A continuous current / peak 5A output short-circuit protected Board 2-fold water protection sealed (Plastik70 protective varnish) Dimensions 26x13x8mm Weight 11g Input cable red / black 0,75 silicone sheath BEC output cable 30 cm Graupner JR connector