Piste King Funktionsmodellbau

PAGE

Beacon, orange, and with integrated electronics

Rotating beacon, orange, with integrated electronics and SMD LEDs, threaded base M5, square cover, scale 1/16, 4-12V 2-wire connection, approx. 35mA, 160 rpm. H=14,5mm, D=10mm. Wide voltage range 4-12V. True-to-original function. Innovative LED technology. Integrated electronics. Two-wire connection. Long service life. Easy to install. Maintenance-free. Scale look. MS pipe 3x0,3mm (item 2326) is suitable for the STECK base! We are now supplying version 2! Would you like to switch this rotating beacon on and off with the remote control? No problem! We recommend a simple and inexpensive memory switch - the PS4a (item 3022). This switch gives you 4 separately switchable outputs! So you can use it to turn this rotating beacon and 3 other light functions on and off!

Available immediately, delivery time: 1-4 days

Product number: 4957

Ab € 35,00 *

Subscriptions

Details

Beacon, orange, and with integrated electronics

Rotating beacon, orange, with integrated electronics and SMD LEDs, 3mm plug-in base, square cover, scale 1/16, 4-12V 2-wire connection, approx. 35mA, 160 rpm. H=14,5mm, D=10mm. Wide voltage range 4-12V. True-to-original function. Innovative LED technology. Integrated electronics. Two-wire connection. Long service life. Easy to install. Maintenance-free. Scale optics. MS pipe 2,5x0,45mm (item 2325) is suitable for the plug-in base! Would you like to switch this rotating beacon on and off with the remote control? No problem! We recommend a simple and inexpensive memory switch - the PS4a (item 3022). This switch gives you 4 separately switchable outputs! So you can use it to switch this rotating beacon and 3 other light functions on and off!An alternative would be item 8068.

Available immediately, delivery time: 1-4 days

Product number: 4958

Ab € 35,00 *

Subscriptions

Details

Beacon, orange, and with integrated electronics

Rotating beacon, orange, with integrated electronics and SMD LEDs, plug-in base 3mm round cover, scale 1/16, 4-12V 2-wire connection, approx. 35mA, 160 rpm. H=13,5mm, D=10mm wide voltage range 4-12V. True-to-original function. Innovative LED technology. Integrated electronics. Two-wire connection. Long service life. Easy to install. Maintenance-free. Scale optics. MS pipe 2,5x0,45mm (item 2325) is suitable for the plug-in base! Would you like to switch this rotating beacon on and off with the remote control? No problem! We recommend a simple and inexpensive memory switch - the PS4a (item 3022). This switch gives you 4 separately switchable outputs! So you can use it to switch this rotating beacon and 3 other light functions on and off!An alternative would be item 8068.

Available immediately, delivery time: 1-4 days

Product number: 4948

Ab € 35,00 *

Subscriptions

Details

Rotating flashing light, yellow, with integrated electronics and

Rotating flashing light, yellow, with integrated electronics and SMD LEDs, universal base, scale 1/14, 4-6V, transparent cap, 3-wire connection, approx. 35-120mA, H=6,2mm, D=10,5mm. For M5 thread. Voltage range 4-6V. (4 cells NiMh, BEC voltage) True-to-original function. Innovative LED technology. Integrated electronics. 3-wire connection. Long service life. Easy to install. Can be attached to a 2,5mm tube. Outer diameter of the base part: 4,2mm. Maintenance-free. Scale optics. Transparent cap. 3 rotation speeds and 8 flash sequences adjustable. Universal base (for screwing and plugging!) Would you like to switch this rotating light on and off with the remote control? No problem!We recommend a simple and inexpensive memory switch - the PS4a (item 3022). This switch gives you 4 separately switchable outputs! You can use it to switch this rotating beacon and 3 other light functions on and off!An alternative would be item 8068.Colors of the wires:red: PLUSblack: MINUSyellow: programming cable

Available immediately, delivery time: 1-4 days

Product number: 10997

€ 37,00 *

Subscriptions

Ramp drive for Goldhofer semi-trailers. With engine for

This drive fits the Goldhofer trailer item 6978! The drive set is mounted on the model and controls the ramps with a gear motor. The upper and lower end positions are each secured with a limit switch! The limit switches are already wired and ready for installation. All that remains is to solder the cables to the motor! A battery voltage of 7,2-9.6 volts is intended for operation. If operation must be carried out with a higher voltage (e.g. 12V), you can use a speed controller and operate it with only approx. 60% "servo travel". As a big highlight, the ramps can still be moved sideways! Even if this is not possible by remote control, the semi-trailer can also be driven on by very small models! Scope of delivery: - Gear motor - Worm gear (worm pre-mounted on motor)< - Limit switch, pre-assembled and wired - New, continuous shaft for ramps - Side cover caps for shaft - New ramp holders, suitable for new shaft (can be moved sideways!) - Gear housing base plate (functions as a drilling template) - Gear housing cover - Instructions, screws, cable Operation is possible with a polarity reversing switch or speed controller (not included!) Speed controller: Thor4 (item 3020) Polarity reversing switch: items 9856, 3569. This ramp drive only fits the Goldhofer trailer (item 6978).

Available immediately, delivery time: 1-4 days

Product number: 10770

€ 149,00 *

Subscriptions

Beacon, orange, and with integrated electronics

Rotating beacon, orange, with integrated electronics and SMD LEDs, threaded base M5, square cover, scale 1/12, 4-12V 2-wire connection, approx. 35mA, 160 rpm. H=17mm, D=12mm, wide voltage range 4-12V. True-to-original function. Innovative LED technology. Integrated electronics. Two-wire connection. Long service life. Easy to install. Maintenance-free. Scale optics. MS pipe 3x0,3mm (item 2326) is suitable for the STECK base! We are now supplying version 2! Would you like to switch this rotating beacon on and off with the remote control? No problem! We recommend a simple and inexpensive memory switch - the PS4a (item 3022). This switch gives you 4 separately switchable outputs! So you can use it to switch this rotating beacon and 3 other light functions on and off!An alternative would be item 8068.

Available immediately, delivery time: 1-4 days

Product number: 4955

Ab € 35,00 *

Subscriptions

Details

Beacon, orange, and with integrated electronics

Rotating beacon, orange, with integrated electronics and SMD LEDs, threaded base M5, round cover, scale 1/16, 4-12V 2-wire connection, approx. 35mA, 160 rpm. H=13,5mm, D=10mm. Wide voltage range 4-12V. True-to-original function. Innovative LED technology. Integrated electronics. Two-wire connection. Long service life. Easy to install. Maintenance-free. Scale optics. MS pipe 3x0,3mm (item 2326) is suitable for the STECK base! We are now supplying version 2! Would you like to switch this rotating beacon on and off with the remote control? No problem! We recommend a simple and inexpensive memory switch - the PS4a (item 3022). This switch gives you 4 separately switchable outputs! So you can use it to switch this rotating beacon and 3 other light functions on and off!An alternative would be item 8068.

Available immediately, delivery time: 1-4 days

Product number: 4947

Ab € 35,00 *

Subscriptions

Details

1 horn for function models. Realist- ischer horn sound for

1 horn for functional models. Realistic horn sound for trucks or construction machines (e.g. excavators). Can be connected directly to the receiver output. Approx. 15x17mm, with M5 thread. Servo cable JR. Electronic horn with the sound of a truck horn. It makes sense to control it via a BUTTON on the transmitter! But of course any other control device (joystick, slider, etc.) can also be used for control. The power supply comes directly from the receiver no additional power supply necessary!

Ready to ship in 5 days, delivery time 1-4 days

Product number: 7020

€ 35,00 *

Subscriptions

Rotating beacon, orange, with integrated electronics

Rotating flashing light, orange, with integrated electronics and SMD LEDs, universal base, scale 1/14, 4-6V, transparent cap, 3-wire connection, approx. 35-120mA, H=6,2mm, D=10,5mm. For M5 thread. Voltage range 4-6V. (4 cells NiMh, BEC voltage) True-to-original function. Innovative LED technology. Integrated electronics. 3-wire connection. Long service life. Easy to install. Can be attached to a 2,5mm tube. Outer diameter of the base part: 4,2mm. Maintenance-free. Scale optics. Transparent cap. 3 rotation speeds and 8 flash sequences adjustable. Universal base (for screwing and plugging!) Would you like to switch this rotating light on and off with the remote control? No problem!We recommend a simple and inexpensive memory switch - the PS4a (item 3022). This switch gives you 4 separately switchable outputs! You can use it to switch this rotating beacon and 3 other light functions on and off!An alternative would be item 8068.Colors of the wires:red: PLUSblack: MINUSyellow: programming cable

Available immediately, delivery time: 1-4 days

Product number: 12413

€ 37,00 *

Subscriptions

. Spare lid f beacon, orange 1: 16 angular, glass Height

. Spare lid f beacon, orange 1: 16 angular, glass height 11mm, diameter 10mm, Note: spare parts for products 4957 4958 and.

Available immediately, delivery time: 1-4 days

Product number: 5374

€ 3,00 *

Subscriptions

1 pair Backfire light strips, red LEDs. zBzur attachment

1 pair of backfire light strips, red LEDs. e.g. for attachment to the wind deflectors of the driver's cab. Can be operated with 5,5-12V voltage. 130mm long. 1 pair of light strips with 25 LEDs per strip. 1x right, 1x left. Each approx. 7,5x130mm. 5 groups per strip with 5 LEDs each, glowing red. Voltage range 5,5V - 12V. Power consumption approx. 25mA each. Attachment with double-sided adhesive tape or glue. The LEDs light up to the rear and to the respective outside.

Available immediately, delivery time: 1-4 days

Product number: 7354

€ 68,00 *

Subscriptions

1x all-round light bar, with integrated electronics and SMD-LE

1x rotating light bar, with integrated electronics and SMD LEDs, ORANGE 5-14V, scale suitable for 1:16 and 1:14 - i.e. Wedico and Tamiya. There are 33 selectable flashing patterns available. This Ecco light bar can be installed on models of scales 1:16 and 1:14. The integrated circuit board is equipped with the latest technology. There are 32 pre-programmed flashing patterns available. The last selected pattern is permanently saved. Mode 33 switches through all flashing patterns one after the other, like a demo mode. There are also 4 brightness levels adjustable. Features: The light bar is pre-assembled and tested. Operating voltage: 5 to 14 volts

Available immediately, delivery time: 1-4 days

Product number: 11974

€ 87,94 *

Subscriptions

Lamp holder with 9 mm spacing, for rotating beacon

Lamp holder with 9 mm spacing, for rotating beacon (Pistenking). Made of cast brass. With 2 fastening screws VA M1,6x6mm. The detailed lamp holder for the rotating beacon has a distance of 9mm from the fastening point. On the inside of the holder there is a hollow groove in which the wires can be guided (laid) invisibly. Size of base: approx. 13x7mm2 VA screws with hexagon head M6x1,6mm are included. The rotating beacons with plug-in base with the article numbers:6 fit this lamp holder

Available immediately, delivery time: 1-4 days

Product number: 11033

€ 22,00 * € 23,00 * (4.35% saved)

Subscriptions

Beacon, orange, and with integrated electronics

Rotating beacon, orange, with integrated electronics and SMD LEDs, 3mm plug-in base, square cover, scale 1/12, 4-12V 2-wire connection, approx. 35mA, 160 rpm. H=17mm, D=12mm, wide voltage range 4-12V. True-to-original function. Innovative LED technology. Integrated electronics. Two-wire connection. Long service life. Easy to install. Maintenance-free. Scale look. 1 piece 38,50 euros. 2 pieces 37,00 euros/piece. 3 pieces or more 35,00 euros/piece. MS pipe 3x0,3mm (item 2326) is suitable for the plug-in base! We are now supplying version 2! Would you like to switch this rotating beacon on and off using the remote control? No problem! We recommend a simple and inexpensive memory switch - the PS4a (item 3022). This switch provides you with 4 separately switchable outputs! You can therefore use it to switch this rotating beacon and 3 other light functions on and off! An alternative would be item 8068.

Available immediately, delivery time: 1-4 days

Product number: 4956

Ab € 35,00 *

Subscriptions

Details

. Spare lid f beacon, orange 1: 12 angular, glass Height

. Spare lid f beacon, orange 1: 12 angular, glass height 13mm, diameter 12mm, Note: spare parts for products 4955 4956 and.

Available immediately, delivery time: 1-4 days

Product number: 5375

€ 3,00 *

Subscriptions

Servo holder for Goldhofer semi-trailers. For the steering servo for g

Servo holder for Goldhofer trailers. For the steering servo for steered trailer axles. For some time now we have been offering an electric drive for the ramps of the Goldhofer semi-trailer low loader from Carson/Veroma. Unfortunately, the steering servo for the trailer axles can no longer be mounted together with the ramp drive at the rear of the trailer as usual. With this new servo holder, the servo is mounted between the axles. This leaves enough space at the rear for the ramp drive!Scope of delivery:- Servo frame with cutout for servo 42x21mm- Printed parts servo frame holder- Spacer sleeve for servo- Instructions, screws, cableRecommended servos: Article 7968 (for standard application) Article 11961 (for more powerful application, digital servo) Article 12254 (for extremely high requirements, digital servo)

Ready to ship in 5 days, delivery time 1-4 days

Product number: 10771

€ 38,00 *

Subscriptions

Ramp drive for Goldhofer trailer TU-4 (Carson). With

Ramp drive for Goldhofer trailer TU-4 (Carson). With motor for 7,2-9,6V. Ramp drive suitable for the Goldhofer-TU4 low-loader trailer from Carson (item 10831 - not included). The drive set is mounted on the model and controls the ramps with a gear motor. The upper and lower end positions are each secured with a limit switch! The limit switches are already wired and ready for installation. All that remains is to solder the cables to the motor! A battery voltage of 7,2-9.6 volts is intended for operation. If operation must be carried out with a higher voltage (e.g. 12V), you can use a speed controller and operate it with only approx. 60% "servo travel". As a big highlight, the ramps can still be moved sideways! Even if this is not possible remotely, the semi-trailer can still be driven by very small models!Scope of delivery:- Gear motor- Worm gear (worm pre-mounted on shaft)- Limit switch, pre-mounted and wired- New, continuous shaft for ramps- Side cover caps for shaft- New ramp holders, suitable for new shaft (can be moved sideways!)- Gear housing base plate (acts as a drilling template)- Gear housing cover (left and right)- Instructions, screws, cableOperation is possible with a polarity reversal switch or speed controller (not included!)Speed controller: Thor4 (item 3020)Polarity reversal switch: items 9856, 3569.

Available immediately, delivery time: 1-4 days

Product number: 11440

€ 149,00 *

Subscriptions

. Spare lid f beacon, orange 1: 16 round, glass Height

Replacement cover for rotating beacon, orange 1:16 round, glass height 10mm, diameter 10mm, Note: Spare part for items 4947 and 4948.

Available immediately, delivery time: 1-4 days

Product number: 5377

€ 3,00 *

Subscriptions

1x all-round light bar, with integrated electronics and SMD-LE

1x rotating light bar, with integrated electronics and SMD LEDs, YELLOW, 5-14V, scale suitable for 1:16 and 1:14 - i.e. Wedico and Tamiya. There are 33 selectable flashing patterns available. This Ecco light bar can be installed on models of the scale 1:16 and 1:14. The integrated circuit board is equipped with the latest technology. There are 32 pre-programmed flashing patterns available. The last selected pattern remains permanently saved. Mode 33 switches through all the flashing patterns one after the other, like a demo mode.Furthermore, 4 brightness levels can be set.Features:The light bar is pre-assembled and tested.Operating voltage: 5 to 14 voltsDimensions: 112.5 x 20.6 x 6 mm (L x W x H)Scope of delivery: 1x Vantage light bar in selected color (pre-assembled) 2x foot elements for assembly (plastic adhesive is not included!) 1x drilling template for precise attachment 1x instructions This excellent product was developed under full license from Ecco Safety Group USA and is optically state of the art for modern trucks.Would you like to switch this light bar on and off with the remote control? No problem!We recommend a simple and inexpensive memory switch, the PS4a (item 3022). With this switch, you have 4 separately switchable outputs available! So you can use it to switch this light bar and 2 other light functions on and off!An alternative would be item 8068.

Available immediately, delivery time: 1-4 days

Product number: 11931

€ 87,94 *

Subscriptions

Beacon, orange, and with integrated electronics

Rotating beacon, orange, with integrated electronics and SMD LEDs, threaded base M5, square cover, scale 1/8, 4-12V 2-wire connection, approx. 35mA, 160 rpm. H=24,8mm, D=17,5mm, wide voltage range 4-12V. True-to-original function. Innovative LED technology. Integrated electronics. Two-wire connection. Long service life. Easy to install. Maintenance-free. Scale look. 1 piece 38,50 euros. 2 pieces 37,00 euros/piece. 3 pieces or more 35,00 euros/piece. MS pipe 3x0,3mm (item 2326) is suitable for the STECK base! We are now supplying version 2! Would you like to switch this rotating beacon on and off using the remote control? No problem! We recommend a simple and inexpensive memory switch - the PS4a (item 3022). This switch gives you 4 separately switchable outputs! You can use it to switch this rotating beacon and 3 other light functions on and off! An alternative would be item 8068.

Available immediately, delivery time: 1-4 days

Product number: 4953

Ab € 35,00 *

Subscriptions

Details

Beacon, orange, and with integrated electronics

Rotating beacon, orange, with integrated electronics and SMD LEDs, plug-in base 3mm round cover, scale 1/12, 4-12V 2-wire connection, approx. 35mA, 160 rpm. H=15,5mm, D=12mm wide voltage range 4-12V. True-to-original function. Innovative LED technology. Integrated electronics. Two-wire connection. Long service life. Easy to install. Maintenance-free. Scale look. MS pipe 3x0,3mm (item 2326) is suitable for the plug-in base! We are now supplying version 2! Would you like to switch this rotating beacon on and off with the remote control? No problem! We recommend a simple and inexpensive memory switch - the PS4a (item 3022). This switch gives you 4 separately switchable outputs! So you can use it to switch this rotating beacon and 3 other light functions on and off!An alternative would be item 8068.

Available immediately, delivery time: 1-4 days

Product number: 4949

Ab € 35,00 *

Subscriptions

Details

Beacon, blue, with integrated electronics u

Rotating beacon, blue, with integrated electronics and SMD LEDs, threaded base M5, square cover, scale 1/12, 4-12V 2-wire connection, approx. 35mA, 160 rpm. H=17mm, D=12mm, wide voltage range 4-12V. True-to-original function. Innovative LED technology. Integrated electronics. Two-wire connection. Long service life. Easy to install. Maintenance-free. Scale look. 1 piece 38,50 euros. 2 pieces 37,00 euros/piece. 3 pieces or more 35,00 euros/piece. MS pipe 3x0,3mm (item 2326) is suitable for the STECK base! We are now supplying version 2! Would you like to switch this rotating beacon on and off using the remote control? No problem!We recommend a simple and inexpensive memory switch - the PS4a (item 3022). This switch provides you with 4 separately switchable outputs! You can therefore use it to switch this rotating beacon and 3 other light functions on and off!An alternative would be item 8068.

Available immediately, delivery time: 1-4 days

Product number: 4961

Ab € 35,00 *

Subscriptions

Details

Beacon, orange, and with integrated electronics

Rotating beacon, orange, with integrated electronics and SMD LEDs, threaded base M5, round cover, scale 1/12, 4-12V 2-wire connection, approx. 35mA, 160 rpm. H=15,5mm, D=12mm. Wide voltage range 4-12V. True-to-original function. Innovative LED technology. Integrated electronics. Two-wire connection. Long service life. Easy to install. Maintenance-free. Scale look. 1 piece 38,50 euros. 2 pieces 37,00 euros/piece. 3 pieces or more 35,00 euros/piece. MS pipe 3x0,3mm (item 2326) is suitable for the STECK base! We are now supplying version 2! Would you like to switch this rotating beacon on and off using the remote control? No problem! We recommend a simple and inexpensive memory switch - the PS4a (item 3022). This switch gives you 4 separately switchable outputs! You can use it to switch this rotating beacon and 3 other light functions on and off! An alternative would be item 8068.

Available immediately, delivery time: 1-4 days

Product number: 4950

Ab € 35,00 *

Subscriptions

Details

Beacon, blue, with integrated electronics u

Rotating beacon, blue, with integrated electronics and SMD LEDs, threaded base M5, square cover, scale 1/16, 4-12V 2-wire connection, approx. 35mA, 160 rpm. H=14,5mm, D=10mm, wide voltage range 4-12V. True-to-original function. Innovative LED technology. Integrated electronics. Two-wire connection. Long service life. Easy to install. Maintenance-free. Scale look. 1 piece 38,50 euros. 2 pieces 37,00 euros/piece. 3 pieces or more 35,00 euros/piece. MS pipe 3x0,3mm (item 2326) is suitable for the STECK base! We are now supplying version 2! Would you like to switch this rotating beacon on and off using the remote control? No problem! We recommend a simple and inexpensive memory switch - the PS4a (item 3022). This switch provides you with 4 separately switchable outputs! You can therefore use it to switch this rotating beacon and 3 other light functions on and off! An alternative would be item 8068.

Available immediately, delivery time: 1-4 days

Product number: 4963

Ab € 35,00 *

Subscriptions

Details

Lampholder with 12 mm distance, for rotating beacon (Pistenkin

Lamp holder with 12 mm spacing, for rotating beacon (Pistenking). Made of cast brass. With 2 fastening screws VA M1,6x6mm. The detailed lamp holder for the rotating beacon has a distance of 12mm from the fastening point. On the inside of the holder there is a hollow groove in which the wires can be guided (laid) invisibly. Size of base: approx. 13x7mm2 VA screws with hexagon head M6x1,6mm are included. The rotating beacons with plug-in base with the article numbers:6 fit this lamp holder

Available immediately, delivery time: 1-4 days

Product number: 11031

€ 22,00 *

Subscriptions

1 4er-round light bars, m.integrierter Electronics &

1 4-round light bar, with integrated electronics and SMD LEDs, ORANGE, 4-12V, square cover, scale suitable for Wedico and Tamiya. 3-wire connection, H=14mm, W=15mm, L=117mm. Large voltage range 4-12V. True to original function. Rotation speed 160 rpm. Innovative SMD LED technology. 4x 10 LEDs. Integrated electronics. Three-wire connection. Separately switchable center lighting. True to original rotation speed difference! The 4 rotating lights deliberately do not run synchronously! Long service life. Easy to install. Maintenance-free. Scale look. A memory switch is suitable for switching the two functions (all-round light and center lighting) on/off separately. Eg article 3022/3024. Fastening via 2 M3 threads (distance 77,5mm). Please note the maximum thread depth of 8mm! All individual rotating lights can be easily programmed to one of 10 different light effects! Would you like to turn this light bar on and off using the remote control? No problem! We recommend a simple and inexpensive memory switch - the PS4a (item 3022). This switch provides you with 4 separately switchable outputs! So you can use it to switch this light bar and 2 other light functions on and off! An alternative would be article 8068.

Available immediately, delivery time: 1-4 days

Product number: 6386

€ 159,00 *

Subscriptions

Flashing beacon, BLUE, with integrated electronics 1: 14

Rotating flashing light, BLUE, with integrated electronics and SMD LEDs, universal base, scale 1/14, 4-6V, transparent cap, 3-wire connection, approx. 35-120mA, H=6,2mm, D=10,5mm. For M5 thread. Voltage range 4-6V. (4 cells NiMh, BEC voltage) True-to-original function. Innovative LED technology. Integrated electronics. 3-wire connection. Long service life. Easy to install. Can be attached to a 2,5mm tube. Outer diameter of the base part: 4,2mm. Maintenance-free. Scale optics. Transparent cap. 3 rotation speeds and 8 flash sequences adjustable. Universal base (for screwing and plugging!) Would you like to switch this rotating light on and off with the remote control? No problem!We recommend a simple and inexpensive memory switch - the PS4a (item 3022). This switch gives you 4 separately switchable outputs! You can use it to switch this rotating beacon and 3 other light functions on and off!An alternative would be item 8068.Colors of the wires:red: PLUSblack: MINUSyellow: programming cable

Available immediately, delivery time: 1-4 days

Product number: 10998

€ 37,00 *

Subscriptions

Switch with diodes and cables for Goldhofer ramp drive

2 switches with diodes and cables for Goldhofer ramp drive.

Available immediately, delivery time: 1-4 days

Product number: 10872

€ 12,99 *

Subscriptions

2-way distributor (Kingbus system) with 15cm cables.

2-way distributor (Kingbus system) with 15cm cables. This distributor can be used to expand the Kingbus system with new light modules. It works like a multiple socket in the home. This 2-way distributor is very suitable for connecting two rear light modules and the infrared transmitter module at the rear of a tractor unit. This means that only one twin cable leads to the front to the central module. This distributor is available with different cable lengths: 15, 30 and 50 cm.

Available immediately, delivery time: 1-4 days

Product number: 10937

€ 8,50 *

Subscriptions

4 distribution board (Kingbus system) with 15cm cables

4-way distributor (Kingbus system) with 15cm cables. This distributor can be used to expand the Kingbus system with new light modules. It works like a multiple socket in the home. This 4-way distributor is very suitable for connecting two rear light modules and the infrared transmitter module at the rear of a tractor unit. This means that only one twin cable leads to the front to the central module. This distributor is available with different cable lengths: 15, 30 and 50 cm.

Available immediately, delivery time: 1-4 days

Product number: 10875

€ 9,50 *

Subscriptions

. Spare lid f beacon, blue, 1: 16 angular, glass Height

Replacement cover for rotating beacon, blue, 1:16 square, glass height 11mm, diameter 10mm, Note: Spare part for items 4963 and 4964.

Available immediately, delivery time: 1-4 days

Product number: 5383

€ 3,00 *

Subscriptions

Horn for function models. Realistic horn

Available immediately, delivery time: 1-4 days

Product number: 4964

Ab € 35,00 *

Subscriptions

Details

1 multi-tone fanfare. Realistic multi-tone fanfare for

1 multi-tone fanfare. Realistic multi-tone fanfare for RC models. Connect directly to the receiver output. Approx. 15x17mm. With M5 thread. Servo cable JR. No additional power supply is required if the module is connected to a receiving channel!

Available immediately, delivery time: 1-4 days

Product number: 7271

€ 35,00 *

Subscriptions