Semitrailer

Search for your Model Truck a beautiful Model Semi? Take your time and browse through this well stocked Modellbaushop around until you have your dream semi-trailers found.

Select the right type of trailer for your model truck from:

Curtainsider for your Truck
Stanchions telescopic semitrailers for your model truck
Refrigerated container semitrailer for your Tamiya Truck

All Tamiya / Carson semitrailers models are made of very high quality and with attention to detail.

PAGE

Tip

1x Carson Goldhofer trailer in Tamiya scale

1x Carson Goldhofer semi-trailer in Tamiya scale. Kit with assembly instructions. With 2 access ramps and support. Unpainted. Weight approx. 6000g. (907060) Corresponds to the original STN-L3. Steel frame laser-cut and spot-weldedFoldable and split loading ramps3 axles with twin tires and dummy air springs12 low-loader tires7-chamber tail lights (without bulbs)License plate plate (can be illuminated)Plateau with side wallsAluminum underrun protection, milledTrailer supports, mechanically adjustableHydraulic cylinder dummyIllustrated assembly instructionsDimensions: 910/1220x190x142mm Weight approx. 6.000 gr.Numerous accessories are available for this model: Conversion kit with 3 steering axles (item 9999)Conversion kit with 3 steering axles (full metal linkages) item 10857 Conversion kit with 5 steering axles (item 10450)Electric trailer supports (item 9994)Electric ramp operation (item 10770)Steering servo installation kit (item 10771)

Available immediately, delivery time: 1-4 days

Product number: 6978

€ 479,00 * € 585,00 * (18.12% saved)

Subscriptions

Ramp drive for Goldhofer semi-trailers. With engine for

This drive fits the Goldhofer trailer item 6978! The drive set is mounted on the model and controls the ramps with a gear motor. The upper and lower end positions are each secured with a limit switch! The limit switches are already wired and ready for installation. All that remains is to solder the cables to the motor! A battery voltage of 7,2-9.6 volts is intended for operation. If operation must be carried out with a higher voltage (e.g. 12V), you can use a speed controller and operate it with only approx. 60% "servo travel". As a big highlight, the ramps can still be moved sideways! Even if this is not possible by remote control, the semi-trailer can also be driven on by very small models! Scope of delivery: - Gear motor - Worm gear (worm pre-mounted on motor)< - Limit switch, pre-assembled and wired - New, continuous shaft for ramps - Side cover caps for shaft - New ramp holders, suitable for new shaft (can be moved sideways!) - Gear housing base plate (functions as a drilling template) - Gear housing cover - Instructions, screws, cable Operation is possible with a polarity reversing switch or speed controller (not included!) Speed controller: Thor4 (item 3020) Polarity reversing switch: items 9856, 3569. This ramp drive only fits the Goldhofer trailer (item 6978).

Available immediately, delivery time: 1-4 days

Product number: 10770

€ 149,00 *

Subscriptions

Trailer support pair (Carson FLIEGL trough trailer)

1 pair of trailer supports (Carson FLIEGL dump trailer) 1 pair, metal. Aluminum housing, steel support with guide, INCLUDING 2 MOTORS, support plate. Total height 76-114mm. (907218). This set contains the supports suitable for the Fliegl trailer (item 8537) and 2 matching motors (item 8538). The motors are designed for operation with 7,2V. This set fits almost all Carson trailer chassis (except Goldhofer trailers).

Ready to ship in 5 days, delivery time 1-4 days

Product number: 8890

€ 175,00 * € 199,98 * (12.49% saved)

Subscriptions

Tip

Carson End Dump semitrailer FLIEGL. Tamiya scale

1x Carson rear tipping semi-trailer in Tamiya scale. Kit with assembly instructions. Tailgate with 2-hook lock. FLIEGL - Stone Master - round trough. Weight approx. 4600g. Max. load 10kg. Trough and rear wall made of sheet steel, laser-welded.Trough is supplied in steel gray, oxidized (rust protection).Wheel suspension made of GRP with longitudinal control armsAir spring dummies (coil springs)Chassis, milled, laser-welded6 trailer rims, wide, ball bearing!6 wide tires7-chamber tail lights (without bulbs)License plate plate (illuminable)Plastic mudguards with holdersAutomatic 2-hook locking rear flapRear underrun protectionTrailer supports, mechanically height-adjustablePlatform aluminum/plasticHydraulic cylinder dummyDimensions: 660x185x235mm Weight 4.600 gr. Max.Load 10kg.The following accessories are available: (not included)Trailer support pair: Article 8537Motor for trailer support pair (2x required): Article 8538orTrailer supports as a set: Article 8890Tilt drive (spindle): Article 8535Motor for tilt drive: Article 8536or:Tilt drive set: Article 9043Alternative trailer support: Article 11344

Available immediately, delivery time: 1-4 days

Product number: 8472

€ 639,95 * € 750,00 * (14.67% saved)

Subscriptions

1 geared motor for driving Fliegl trailer supports

1 gear motor for driving Fliegl trailer supports (item 8537). 2 motors are required for one pair of supports! For 7,2V operation. (907199). In order to be able to operate the supports of the Fliegl trailer electrically, 2 of this motor are required! (Pair of supports: item 8537). Under item number 8890 you will find a complete set (with a price advantage!) consisting of supports and support motors! Technical data: Overall length: 32,8mm Length without shaft: 26,6mm Max. Diameter (motor): 13,5mmShaft diameter: 3mm with one-sided flatteningNominal voltage: 7,4V DCWorking voltage: 6,0 - 8,0V DCIdle speed: 130 rpmSpeed in continuous operation: 100 rpmContinuous current: 0,8AContinuous torque: 20mNmPeak torque: 75mNmReduction ratio: 100:1Weight: 12gr.

Available immediately, delivery time: 1-4 days

Product number: 8538

€ 33,36 * € 34,99 * (4.66% saved)

Subscriptions

1 tilt drive SET (spindle drive) e.g. Carson

1 tilt drive set (spindle drive) e.g. Carson dump truck FLIEGL StoneMaster. Pre-assembled tilt drive PLUS motor. (Shipping weight 750g). 907217+907166. Special spindle tilt drive for the dump trailer FLIEGL StoneMaster from Carson. (Suitable motor is included - item 8536). Also suitable for operating the tilt function of the central axle trailer (item 11354). Recommended controller for the tilt motor: THOR14 (item 6866) - not included.

Ready to ship in 5 days, delivery time 1-4 days

Product number: 9043

€ 249,00 * € 289,99 * (14.13% saved)

Subscriptions

Carson 2-axle rear tipper semitrailer. 1: 14 500907312

Carson rear tipper semi-trailer in Tamiya scale. 2-axle dump truck. Tailgate with 2-hook lock. Kit. Max. load 10kg. Trough and rear wall made of hard PVC, milledAir spring dummies (coil springs)Aluminum chassis, milled8 ball bearings6 trailer rims, wide6 wide tires7-chamber tail lights (without bulbs)License plate plate (illuminable)Plastic mudguards with holdersLocking rear flapAluminum underrun protection, milledTrailer supports, mechanically adjustableAluminum/plastic platformHydraulic cylinder dummyFor automatic operation, the following optional items (not included!) are recommended:-Item 8535 (tilting spindle)-Item 8536 (tilting motor for tilting spindle)-Additionally, for the remote control, an electronic switch or a small speed controller (more convenient) as required.Dimensions:Total length: 620mmWidth 185mmHeight: 240mm / tilted: approx. 600mm

Ready to ship in 5 days, delivery time 1-4 days

Product number: 10322

€ 449,50 * € 590,00 * (23.81% saved)

Subscriptions

Alu warning signs with decor. (2 piece). Eg for low loaders

Aluminum warning signs with decoration. (2 pieces). For example for Goldhofer low loaders. Aluminum warning signs for low loaders and trailers.Scope of delivery:2 aluminum warning signs with integrated holder, warning decoration, fastening screws.

Available immediately, delivery time: 1-4 days

Product number: 11683

€ 28,99 * € 29,99 * (3.33% saved)

Subscriptions

Tip

1 Carson End Dump semitrailer FLIEGL.Tamiya scale

1 Carson rear tipping semi-trailer in Tamiya scale. COMPLETE SET with TIPPING SPINDLE SET and SUPPORT SET. FLIEGL - Stone Master - round trough. Weight approx. 4600g. Max. load 10kg. COMPLETE SET with tilt spindle, tilt motor, supports and 2 support motors!Kit with assembly instructions.Tailgate with 2-hook locking.Trough and rear wall made of sheet steel, laser-welded.Trough is delivered in steel gray, oxidized (rust protection).Wheel suspension made of GRP with longitudinal control armsAir spring dummies (coil springs)Chassis, milled, laser-welded6 trailer rims, wide, ball bearing!6 wide tires7-chamber tail lights (without bulbs)License plate plate (can be illuminated)Plastic mudguards with holdersAutomatic 2-hook locking tailgateRear underrun protectionTrailer supports, mechanically height-adjustablePlatform aluminum/plasticHydraulic cylinder dummyDimensions: 660x185x235mm Weight 4.600 gr. max. payload 10kg.SPECIAL SALE - limited to stock!Also included in the set:Tilt spindle with motor (item 9043)Support set (incl. 2 motors), item 8890

Ready to ship in 5 days, delivery time 1-4 days

Product number: 9044

€ 1.028,99 * € 1.239,97 * (17.01% saved)

Subscriptions

Aluminum cylinder holder for Goldhofer low loader

Aluminium cylinder bracket for Goldhofer low loaders. Reinforced design, replaces the plastic brackets included in the kit. Package contents: 1 pair, 1x left, 1x right

Available immediately, delivery time: 1-4 days

Product number: 11679

€ 44,99 * € 46,99 * (4.26% saved)

Subscriptions

Servo holder for Goldhofer semi-trailers. For the steering servo for g

Servo holder for Goldhofer trailers. For the steering servo for steered trailer axles. For some time now we have been offering an electric drive for the ramps of the Goldhofer semi-trailer low loader from Carson/Veroma. Unfortunately, the steering servo for the trailer axles can no longer be mounted together with the ramp drive at the rear of the trailer as usual. With this new servo holder, the servo is mounted between the axles. This leaves enough space at the rear for the ramp drive!Scope of delivery:- Servo frame with cutout for servo 42x21mm- Printed parts servo frame holder- Spacer sleeve for servo- Instructions, screws, cableRecommended servos: Article 7968 (for standard application) Article 11961 (for more powerful application, digital servo) Article 12254 (for extremely high requirements, digital servo)

Available immediately, delivery time: 1-4 days

Product number: 10771

€ 38,00 *

Subscriptions

Ramp drive for Goldhofer trailer TU-4 (Carson). With

Ramp drive for Goldhofer trailer TU-4 (Carson). With motor for 7,2-9,6V. Ramp drive suitable for the Goldhofer-TU4 low-loader trailer from Carson (item 10831 - not included). The drive set is mounted on the model and controls the ramps with a gear motor. The upper and lower end positions are each secured with a limit switch! The limit switches are already wired and ready for installation. All that remains is to solder the cables to the motor! A battery voltage of 7,2-9.6 volts is intended for operation. If operation must be carried out with a higher voltage (e.g. 12V), you can use a speed controller and operate it with only approx. 60% "servo travel". As a big highlight, the ramps can still be moved sideways! Even if this is not possible remotely, the semi-trailer can still be driven by very small models!Scope of delivery:- Gear motor- Worm gear (worm pre-mounted on shaft)- Limit switch, pre-mounted and wired- New, continuous shaft for ramps- Side cover caps for shaft- New ramp holders, suitable for new shaft (can be moved sideways!)- Gear housing base plate (acts as a drilling template)- Gear housing cover (left and right)- Instructions, screws, cableOperation is possible with a polarity reversal switch or speed controller (not included!)Speed controller: Thor4 (item 3020)Polarity reversal switch: items 9856, 3569.

Available immediately, delivery time: 1-4 days

Product number: 11440

€ 149,00 *

Subscriptions

Aluminum ramp hinge for Goldhofer low loader

Aluminum ramp hinge for Goldhofer low loaders. Reinforced design, replaces the plastic hinges included in the kit. (2 pieces). 500907475.

Available immediately, delivery time: 1-4 days

Product number: 11678

€ 28,99 * € 30,99 * (6.45% saved)

Subscriptions

1 ball bearing set for Tamiya trailer, 8 pieces.

1 ball bearing set for Tamiya trailer, 8 pieces. 8x ball bearings 5x11x4mm. The use of ball bearings is recommended! The ball bearings reduce friction - this results in a longer battery life. Tip: It is easier to use the ball bearings immediately during assembly. If you install/replace them later, the axles must be disassembled again.

Available immediately, delivery time: 1-4 days

Product number: 10696

€ 7,98 * € 9,29 * (14.1% saved)

Subscriptions

1x tilt drive motor (spindle drive) matching products

1x tilt drive motor (spindle drive) suitable for item 8535. For 7,2V. 907166. For the lifting drive of the Fliegl tipper. Recommended controller for the tilt motor: THOR14LF (item 11689) - not included. This gear motor is used for the tilt drive of the Fliegel rear tipper and the gooseneck trailer.

Available immediately, delivery time: 1-4 days

Product number: 8536

€ 79,94 * € 84,99 * (5.94% saved)

Subscriptions

Tarp-stay bar center. Spare part for Fliegl Megarunner

1 tarpaulin-pole middle. Spare part for Fliegl Megarunner. For inserting wooden bows. Shooting on both sides.

Ready to ship in 5 days, delivery time 1-4 days

Product number: 11340

€ 7,01 *

Subscriptions

Carson Fliegl 3-axle curtainsider Mega Runner. 500907235

Carson Fliegl 3-axle tarpaulin trailer Megarunner. Tamiya scale. Kit. New door hinges with 270° angle. 500907235. Kit does not contain any pre-painted parts. Kit with 3-axle chassisAir suspension dummies (coil springs) on all 3 axlesSteel frame (laser cut)Red tarpaulin with Fliegl logo6 trailer rims, wide, chrome6 wide tiresWheels have 12 ball bearings7-chamber tail lights (without bulbs)Aluminum underrun protectionLicense plate plate (illuminable)Plastic mudguards with holdersTrailer bumper with lasered Fliegl logoTrailer supports, mechanically height-adjustableSpare wheel holder, single-armDetailed assembly instructionsDimensions: 995x195x270mm Weight 6.000 gr. Max. Load 10kg.Item 9992 (not included) is available as an electric trailer support.Set 8890 can also be used as a trailer support.

Available immediately, delivery time: 1-4 days

Product number: 10321

€ 518,99 * € 635,00 * (18.27% saved)

Subscriptions

Spare spindle for tilting drive Article 8535. spare part

1x replacement spindle for tilt drive item 8535. Fully assembled threaded tube. Consists of spindle tube with base, brass threaded nut. Fliegl spare part. MS threaded nut 8mm (fine).

Available immediately, delivery time: 1-4 days

Product number: 10549

€ 24,20 *

Subscriptions

Decal sheet, self-adhesive film "Frame 2" suitable for scale

Decal sheet, self-adhesive film "Frame 2" suitable for scale 1:16 to 1:14,5. High-quality self-adhesive film with protective layer, splash-proof. Also available in other scales! This decal sheet was specially made for the Fliegl Stonemaster by CARSON. It can of course also be used for any other vehicle. A special ECE-B sticker for the rear marking of the Fliegl Stonemaster is available under item number 8888.

Available immediately, delivery time: 1-4 days

Product number: 8889

€ 19,99 *

Subscriptions

1x ECE70-B sticker. Rear marking from yellow

1x ECE70-B sticker. Rear marking made of yellow reflective self-adhesive material. (1 piece) For semi-trailers and trailers. Full marking approx. 70x14mm. With surface protection. This ECE-B sticker has been specially made for the Fliegl Stonemaster by CARSON (for the rear cross member). It can of course also be used on any other vehicle.

Ready to ship in 5 days, delivery time 1-4 days

Product number: 8888

€ 3,99 *

Subscriptions

Switch with diodes and cables for Goldhofer ramp drive

2 switches with diodes and cables for Goldhofer ramp drive.

Available immediately, delivery time: 1-4 days

Product number: 10872

€ 12,99 *

Subscriptions

Tarpaulin support rod on the left. Spare part for Fliegl

1 tarpaulin support rod on the left. Spare part for Fliegl Megarunner. For inserting wooden bows. One-sided recordings.

Available immediately, delivery time: 1-4 days

Product number: 11341

€ 5,99 *

Subscriptions

Real wood set for planking the Carson flatbed trailer

Real wood set for planking the Carson low-loader trailer Goldhofer STN-L3. 13-piece real wood set. The wood is raw and untreated. Real wood planking for the Goldhofer trailer item 6978. The individual pieces of wood for the roadway parts are mounted on double-sided adhesive tape. The parts for the gooseneck platform do not have any adhesive tape.

Available immediately, delivery time: 1-4 days

Product number: 11842

€ 35,50 *

Subscriptions

Carson rear tipper semi-trailer in Tamiya scale

Carson rear tipper semi-trailer in Tamiya scale. Kit with assembly instructions. Tailgate with 2-hook lock. Weight approx. 4600g. Max. load 10kg. Trough and rear wall made of hard PVC (gray), milledWheel suspension made of GRP with longitudinal control armsAir spring dummies (coil springs)Aluminum chassis, milled, unpainted.6 trailer rims, wide6 wide tires7-chamber tail lights (without bulbs)License plate plate (can be illuminated)Plastic mudguards with holdersLocking rear flapAluminum underrun protection, milledTrailer supports, mechanically adjustablePlatform aluminum/plasticHydraulic cylinder dummyDimensions: 700x185x235mm Weight 4.600 gr. Max.Load 10kg.Matching tipping mechanism (not included) Article 4099, matching tipping motor: Article 4218.Article 9993 is available as an electric trailer support (not included).

Available immediately, delivery time: 1-4 days

Product number: 5723

€ 518,99 * € 620,00 * (16.29% saved)

Subscriptions

1 tilt drive (spindle drive) e.g. for Carson

1 tilt drive (spindle drive) e.g. for Carson dump truck FLIEGL StoneMaster. Pre-assembled tilt drive (without motor). (Shipping weight 650g). 907217. Special spindle tilt drive for the dump trailer FLIEGL StoneMaster from Carson. (Motor not included). Also suitable for 2-axle tipping central axle trailers (new in 2019). Suitable motor: item 8536.

Available immediately, delivery time: 1-4 days

Product number: 8535

€ 189,00 * € 210,00 * (10% saved)

Subscriptions

1 tarpaulin handrail on the right. Spare part for Fliegl Megarunne

1 tarpaulin handrail on the right. Spare part for Fliegl Megarunner. For inserting wooden hoops. One-sided recordings.

Available immediately, delivery time: 1-4 days

Product number: 11720

€ 5,99 *

Subscriptions

1 pair of trailer supports (Carson FLIEGL dump trailer)

1 pair of trailer supports (Carson FLIEGL dump trailer) 1 pair, metal. Aluminum housing, steel support with guide, intended for motor drive, support plate. Total height 76-114mm. (907218). To operate the supports electrically, 2 drive motors item 8538 are required (not included!). Under item number 8890 you will find a complete set (with a price advantage!), consisting of supports and support motors! This pair of supports is suitable for: 8472 : Fliegl-Stonemaster-Rundmulde7256: Semitrailer chassis10322: 2-axle rear tipper7472: 3-axle flatbed trailer7471: 3-axle stake trailer7470: 3-axle box trailer

Available immediately, delivery time: 1-4 days

Product number: 8537

€ 119,00 * € 130,00 * (8.46% saved)

Subscriptions

Splash guard Carson semi-trailer

Available immediately, delivery time: 1-4 days

Product number: 11199

€ 30,99 *

Subscriptions

Wood Bow Set (32 parts) suitable for Carson Tarpaulin

Wood bow set (32 parts) suitable for Carson tarp trailer and Fliegl MegaRunner semi-trailer.

Available immediately, delivery time: 1-4 days

Product number: 10355

€ 22,99 * € 24,99 * (8% saved)

Subscriptions

Switch for dump truck spindle drive

1 switch for dump truck spindle drive. (Tamiya/Carson). The switch can be used to control the gear motor of the spindle drive of a dump truck (item 5723). A BEC socket and two free cables are available for connection. Power is supplied via a 7,2 V NiMH or 7,4 V LiPo battery with BEC plug system. Current load: max. 5A.

Available immediately, delivery time: 1-4 days

Product number: 9115

€ 14,99 * € 15,49 * (3.23% saved)

Subscriptions

3-axle low loader with gooseneck and low bed

3-axle low loader with gooseneck and low bed, pre-equipped for the installation of steering axles. Suitable for Tamiya tractors. Torsion-resistant steel frame, laser-cut and spot-welded (sandwich construction) Gooseneck made of sheet steel 3 axles with twin tires and dummy air springs Pre-equipped spindle drive for lowering and raising the low bed Prepared for the installation of steering axles 12 retractable lashing eyes 12 low-loader tires all 6 rims with ball bearings, double tires made of solid rubber Loading ramps made of aluminum Real wood floor Storage box with lid (magnetic closure) 2 storage compartments under the platform for electronic components 7-chamber tail lights (without bulbs) License plate plate (illuminable) 2 work lights Rotating beacon (without electronics) 4 extendable warning signs Mud flaps Instructions and decal sheet Technical details Length 1.150 mm Width 205 mm Height 170 mm Total weight 7.500 g, gooseneck 2.500 g, low bed 5.000gLifting force approx. 25.000gA variety of accessories are available for this item.Matching steering axles are optionally available as item 13174. Gear motor for the tilt spindle: item 8536

Available immediately, delivery time: 1-4 days

Product number: 13171

€ 720,00 * € 850,00 * (15.29% saved)

Subscriptions

Trailer transport box made of 9mm birch multiplex, up to 103cm

Transport box made of 9mm birch multiplex. The box is ready to use and painted with 2K clear varnish. A sturdy metal handle (foldable) is embedded on the top. Dimensions for trailers up to 103cm! Universal transport box suitable for all current Carson and Tamiya trailers up to a maximum of 103cm in total length. Blocks (not included) can be mounted on the included sliding floor to fix and lift the model. The model then sits on the frame parts, so that there are guaranteed to be no more flat spots on the tires.Inner dimensions:Length: 1030 mmWidth: 250mmHeight: 340mmExternal dimensions:Length: 1060mmWidth: 270mmHeight: 380mmWeight: approx. 9kg

Ready to ship in 20 days, delivery time 1-4 days

Product number: 12379

€ 154,00 *

Subscriptions

Carson 20 Ft. Sea container kit suitable for Carson frame

Carson 20 Ft. Sea Container Kit to match Carson 20Ft. Carson Container Chassis. Matches Tamiya Trucks. Height 185mm. Length 432mm. Width 180mm.

Ready to ship in 5 days, delivery time 1-4 days

Product number: 11741

€ 180,00 * € 200,00 * (10% saved)

Subscriptions

Set of low loaders. Fulda tires and SAF Felden. Tamiya scale

Low loader set. Fulda low loader tires and SAF rims. Suitable for the Goldhofer low loader. (500907141) Tire dimensions: 59 x 29 x 16mm (outside x inside x wide)

Ready to ship in 5 days, delivery time 1-4 days

Product number: 11194

€ 42,99 * € 47,99 * (10.42% saved)

Subscriptions

Lashing set (universal) for low loaders. For example for Goldhofer

Delivery according to product photo.

Available immediately, delivery time: 1-4 days

Product number: 11682

€ 27,99 * € 29,49 * (5.09% saved)

Subscriptions

Tamiya trailer chassis for Tamiya 20 Ft. Container

Trailer chassis for Tamiya 20 ft. container. Suitable for Tamiya trucks. Length 475mm. Width 180mm. Height 135mm. (907334) Dimensions: 475x180x135mm Technical details: 1. Aluminum frame (black anodized) 2. Swing axle suspension 3. Leaf springs 4. Mechanical seat supports 5. Tires with foam inserts Matching light set: Item 7735 (not included).

No longer available

Product number: 11740

€ 222,11 * € 275,00 * (19.23% saved)

Subscriptions

Details

1 Tamiya stanchion telescopic trailer US. Tamiya scale

1 Tamiya US stanchion telescopic trailer. Tamiya scale. Kit with assembly instructions, stanchion structure, aluminum drawbar. Weight approx. 2550g. Max. payload 4kg. Kit consisting of:2-axle chassisStanchion structureGRP wheel suspension with longitudinal control armsLeaf spring suspensionMilled aluminum chassis4 chrome-plated double rims8 tiresRear bumper with tail lights (without bulbs)Mud flaps, adjustable aluminum drawbarDetailed, illustrated assembly instructionsDimensions: 709x186x215mm Weight 2.550 g. Max. payload 5kg.

End of life - article no longer available!

Product number: 7975

€ 256,85 * € 285,00 * (9.88% saved)

Subscriptions

Details

BROSHUIS 5-axle tied loader trailer incl. 2-axle extension

BROSHUIS 5 axle low loader trailer including 2 axle extension module by Nooxion. Suitable for Tamiya tractors. Officially licensed by BROSHUIS. Painted gray. Broshius Holland 5 + 2 axle low loader for Tamiya models The model is delivered pre-assembled and contains 7 mounted 26 kg servos Features All 7 axles steerable All axles separately adjustable Independent wheel suspension fully suspended Numerous lashing points Extendable widening supports Tiltable saddle plate Full metal: high dead weight of approx. 7 kg Total length approx. 120 - 160 cm Bed width: 200 mm max. total width (with widening): 262 mm Height of low bed above roadway: 75 mm Height of fifth wheel point: 100-110 mm Hollow chamber tires Foam inserts for tires Tilt of the bed can be adjusted for ideal contact pressure and height adjustment to match the fifth wheel plate of the tractor Beacon lights are NOT included!

No longer available

Product number: 11790

€ 2.790,00 * € 2.995,00 * (6.84% saved)

Subscriptions

Details

1 Tamiya tanks GALLANT EAGLE. Tamiya scale

1 Tamiya tank trailer GALLANT EAGLE. Tamiya scale. Kit with assembly instructions, tank, trailer supports. Weight approx. 3800g. Max. payload 5kg. Chrome-plated tankGRP wheel suspension with longitudinal control armsLeaf spring suspensionMilled aluminum chassis4 trailer double rims8 tiresRear bumper with tail lights (without bulbs)Plastic mudguards with bracketsMud flaps, wheel chocks, hose containerTrailer supports, mechanically adjustableDetailed, illustrated assembly instructionsDimensions: 814x186x225mm Weight 4.400 g. Max. payload 5kg.

Ready to ship in 5 days, delivery time 1-4 days

Product number: 7971

€ 399,00 * € 455,00 * (12.31% saved)

Subscriptions

1 Tamiya Flatbed US Style. Tamiya scale

1 Tamiya flatbed trailer US style. Tamiya scale. Kit with assembly instructions, flatbed, trailer supports. Weight approx. 2480g. Max. payload 4kg. Kit consisting of:2-axle chassisFlatbed constructionGRP wheel suspension with trailing armsLeaf spring suspensionMilled aluminum chassis4 chrome-plated double rims8 tiresRear bumper with tail lights (without bulbs)Mud flaps, wheel chocks, side stanchions with chainsTrailer supports, mechanically adjustableDetailed, illustrated assembly instructionsDimensions: 711x192x215mm Weight 2.480 g. Max. payload 5kg.

Ready to ship in 5 days, delivery time 1-4 days

Product number: 7973

€ 249,00 * € 265,00 * (6.04% saved)

Subscriptions

Control station, add-on part for dump truck. Kit exists

Control station, accessory for dump truck. The kit consists of a milled hard PVC plate. The individual parts must be separated, sanded, glued and painted. Dimensions: Width: 153mm Total height: 135mm Depth: approx. 70mm Suitable for a frame width of 96mm.

Ready to ship in 5 days, delivery time 1-4 days

Product number: 10865

€ 57,99 * € 63,99 * (9.38% saved)

Subscriptions

Trailer support for Carson Fliegl Stone Master semi-trailer

1x trailer support for Carson Stone Master trailer. For operating voltage 7,2V. Trailer support suitable for the Carson Stone Master trailer. (Semi-trailer), article 8472 (not included). It is attached to the frame with the screws provided. The trailer support can lift a guaranteed maximum weight of 15kg. A higher weight is possible - but this can damage the mechanics! In most cases the weight is divided between the axles and the trailer support, so that a load with a significantly higher weight than 15kg is possible. Color: Painted in matt black. Other colors possible for an additional charge. Special features: Housing and racks are made of brass. Motor and gearbox from Faulhaber are splash-proof. Suitable for the Carson Stone Master (rear tipper trailer). Technical data: -Width: 125 mm (frame width) -Tooth rack: 8 mm x 8 mm -Weight: 260g -Operating voltage: 7,2 (if 12V is required, please note this in the checkout process) You can find 2 support controls for this trailer support here: Article 10675 (for 12V operation) Article 10681 (for 7,2V operation) Article 10676 (manual switch) These articles are NOT included in the scope of delivery of the support! The support control allows for simple and clean wiring.

No longer available

Product number: 11344

€ 269,00 *

Subscriptions

Details

Control panel Fliegl dump truck. plastic, grey

Control panel Fliegl dump truck. plastic, grey. Replacement injection molding for the construction of a control station.

Ready to ship in 5 days, delivery time 1-4 days

Product number: 12428

€ 19,29 *

Subscriptions

Carson 3-axis Rungenauflieger. Tamiya scale. kit m

Carson 3-axle stake trailer. Tamiya scale. Kit with assembly instructions. With dummy air springs, underrun protection. Weight approx. 4800g. Max. load 10kg. Kit with 3-axle chassisAir spring dummies (coil springs) on all 3 axlesAluminum chassis, milled6 trailer rims, wide, gray-silver6 wide tiresWheels have double ball bearings2-chamber tail lights (without bulbs)License plate plate (can be illuminated)Plastic mudguards with holdersBumper with rubber buffersAluminum underrun protection, milledTrailer supports, mechanically height-adjustableAluminum stanchions with toothed contact surfacesSpare wheel holder with spare wheelDetailed assembly instructionsDimensions: 7x990x195mm Weight 260 gr. Max.Load 4.800kg.Item 10 (not included) is available as an electric trailer support.Item 9992 (for 3104V) is suitable for lighting the tail light units.

No longer available

Product number: 7471

€ 419,99 * € 490,00 * (14.29% saved)

Subscriptions

Details

Noteboom 3 axle low loader trailer by Nooxion

Noteboom 3 axle low loader trailer by Nooxion. Suitable for Tamiya tractors. Officially licensed by Noteboom. Semi-low loader Nooteboom OSDS-48-03EB from Nooxion for Tamiya models. The trailer is made entirely of CNC-machined aluminum and has 3 axles, an extendable loading floor, an extendable widening of the loading floor. The support legs and ramps can be remote controlled. The scale model is equipped with automatic folding ramps that offer a low angle of inclination, just like the original Nooteboom OSDS. The axles are air-sprung.The model has various storage spaces, tool boxes and lashing rings and of course the official Nooteboom logos.FeaturesAir suspensionExtendable loading floorRemote-controlled supportsRemote-controlled rampsNumerous lashing pointsStorage box on gooseneck platform with lidRetractable lashing optionsFull metal: 9kg weightPre-paintedVarious stickers2 work lights incl. LEDs at the rear (ramps)2 rear light units incl. LEDsTechnical dataLength of gooseneck: 35,2 cmLength of loading floor: 63,8 cmLength of extension of loading floor: 29cmTotal length: 99cmExtended total length: 999 + 400mmWidth without roadway widening: 200mmAdditionally required:Battery pack 6V approx. 2000-2500 mAhKing bolt, suitable for the fifth wheel plate of the towing vehicle (on the underside of the saddle plateau there are 3 threaded holes M3 at a distance of 8mm each)Lighting control e.g. from Servonaut

Ready to ship in 20 days, delivery time 1-4 days

Product number: 11788

€ 2.330,00 *

Subscriptions

Carson Tipper Trailers Tam. Scale. FINISHED

Carson rear tipper semi-trailer in Tamiya scale. 2-axle tipper. Tailgate with 2-hook lock. FINISHED MODEL. Max. load 10kg. Trough and rear wall made of hard PVC, milledAir spring dummies (coil springs)Aluminum chassis, milledball bearings4 trailer rims, wide4 wide tires7-chamber tail lights (with lighting boards)License plate plate (can be illuminated)Plastic mudguards with holdersRear flap lockAluminum underrun protection, milledTrailer supports, mechanically adjustablePlatform aluminum/plasticHydraulic cylinder dummyFINISHED MODEL. Built up and professionally painted.Spindle drive and trailer lighting set to match MFC-xx are assembled and ready for use.The tipping function/tilting spindle is operated via a 3-way switch. The vehicle frame is powder-coated (black) and the trough body is painted silver.

No longer available

Product number: 10821

€ 666,00 * € 1.749,99 * (61.94% saved)

Subscriptions

Details

Nooxion Broshuis 2+5 extension, real wood (6 pieces)

Nooxion Broshuis 2+5 extension. Lane extensions (6 pieces) suitable for the Broshuis 2+5 trailer. Made of real wood, natural.

Available immediately, delivery time: 1-4 days

Product number: 12366

€ 19,94 *

Subscriptions

Carson 20 Ft. Refrigerated container kit suitable for Carson 20Ft.

Carson 20 Ft. Refrigerated container kit suitable for Carson 20Ft. Carson container chassis. Suitable for Tamiya Trucks. Height 185mm. Length 465mm. Width 180 mm.

Ready to ship in 5 days, delivery time 1-4 days

Product number: 11742

€ 209,00 * € 225,00 * (7.11% saved)

Subscriptions

Carson 3-axle stake trailer. Tamiya scale. Kit

Carson 3-axle stake trailer V3. Tamiya scale. Kit with assembly instructions. With dummy air springs, underrun protection. Weight approx. 5100g. Max. payload 10kg. 500907629 Tamiya New 2021The 3-axle stake trailer from CARSON for transporting long timber or similarly long loads is a perfect addition to the TAMIYA tractors. The basis for the trailer is a newly developed torsion-resistant frame (sandwich construction) made of 3 and 1 mm laser-cut sheet steel. A new suspension is also included, which can be optionally raised by 8 mm and thus compensates for the fifth wheel level of a raised tractor. However, this can also be installed without raising the vehicle; both suspension variants are included in the kit. The installed shock absorber and air spring dummies function as on/off spring travel limiters. This enables greater axle articulation and reproduces a true-to-original driving image. Depending on the load and requirements, the six aluminum stanchions on the chassis can be infinitely positioned or removed. These are loosened or fixed using the two countersunk grub screws. A solid steel front wall ensures that the load is secured to the front of the tractor. Two work lights (500907144) can optionally be mounted on the front wall and on the rear of the frame; the fastenings are already provided. A sturdy underrun protection and a spare wheel holder made of steel complete the detailing of the model.Technical details:Torsion-resistant steel frame in sandwich constructionFrame made of 3 and 1 mm sheet steel, laser cut and CNC bentSolid front wall made of steelStake poles (one-piece) milled from solid aluminumStake holder can be loosened using two grub screws and repositioned or removed as required.Detailed trailer axles with dummy air springs, optionally raised by + 8mmSolid underrun protection made of steel (left/right)Single-arm spare wheel holder made of steel with spare wheelBall-bearing chrome rims with wide off-road tires7-chamber taillights and license plate holder includedDecorative set, detailed assembly instructionsTechnical data Length 980mm Width 190mm Height 310mm Weight 5,1kgThis article only concerns the 3-axle trailer. Accessories, load, tractor and other visible accessories are NOT included in the scope of delivery.

Available immediately, delivery time: 1-4 days

Product number: 12142

€ 499,00 * € 600,00 * (16.83% saved)

Subscriptions

Carson 1:14 trailer chassis 20/40 ft. Container

Carson trailer chassis for 20/40 foot (ft.) containers from Carson. Suitable for 1:14 scale. 915mm length, 140mm height, 190mm track width. 500907348 CNC milled aluminum frame

Ready to ship in 5 days, delivery time 1-4 days

Product number: 12152

€ 324,00 * € 410,00 * (20.98% saved)

Subscriptions

Carson 1:14 ramp set suitable for TU4 (2)

Ramp set from Goldhofer TU4 low-loader trailer. **Discontinued item

Ready to ship in 5 days, delivery time 1-4 days

Product number: 12155

€ 198,99 * € 200,00 * (0.5% saved)

Subscriptions

Set of steel support rods for Goldhofer trailer ramps

1 set of steel handrails for Goldhofer trailer ramps.

Available immediately, delivery time: 1-4 days

Product number: 12827

€ 14,28 * € 14,49 * (1.45% saved)

Subscriptions

Frame part (left) 928mm long from the Tamiya aluminum refrigerated trailer

Frame part (left) 928mm long from the Tamiya refrigerated trailer. aluminum Original spare part.

Ready to ship in 5 days, delivery time 1-4 days

Product number: 11691

€ 26,08 *

Subscriptions

Frame part (right) 928mm long from the Tamiya refrigerated trailer

Frame part (right) 928mm long from the Tamiya refrigerated trailer. aluminum Original spare part.

Ready to ship in 5 days, delivery time 1-4 days

Product number: 11692

€ 26,08 *

Subscriptions

Carson 3-axle flatbed trailer. Tamiya scale 500907650

Carson 3-axle flatbed trailer. V3. Tamiya scale. Kit with assembly instructions. With dummy air springs, underrun protection. Weight approx. 4400g. Max. load 10kg. 3-axle flatbed trailer version 3, made of steel.Scope of delivery:Laser-cut and drilled frame made of steel with kingpins, height-adjustable trailer supports.New axle suspension optionally with +8mm lift (included).Solid front wall made of aluminum.Underrun protection made of steel.3 axles with true-to-original air spring dummies.12 ball bearings.6 trailer wide tires with chrome-plated plastic rims.Fender, semi-circular.Spare wheel holder (made of steel) with spare wheel.Real wood floor applicationAluminum bumper with rubber buffers and license plate holder.7-chamber tail lights (optionally illuminated with the circuit boards item 3103, 3104 or 3105).Screws and small parts required for assembly.Illustrated assembly instructions.16 lashing eyes.As electrical Set 8890 can be used for supports.Dimensions:Length: 981mmWidth: 195mmHeight: 210mmWeight: 4400 g.With the appropriate conversion kit (not included), the flatbed trailer can be converted into a building materials trailer with functional aluminum side walls.

Ready to ship in 5 days, delivery time 1-4 days

Product number: 12584

€ 499,80 * € 540,00 * (7.44% saved)

Subscriptions

Servo mount set for steering axle. For low loader steering axle

Servo mount set for steering axle. For low loader steering axle linkage, servo mount made of steel. M3 ball head linkage made of steel.

Available immediately, delivery time: 1-4 days

Product number: 13329

€ 30,50 * € 31,49 * (3.14% saved)

Subscriptions

PAGE