Go to home page
Wish lists
€ 0,00 *


RC articles

Filter Products

Memory switch PS4a with 4x 4A output 4x On/Off
Memory switch PS4a with 4x 4A output 4x On/Off
1x memory switch PS4a with 4x 4A output 4x on/off function on 1 RC channel max. voltage 20V. 13x15x2,5mm, CTI product switching module (4x memory) with 4 separately switchable outputs. Each output can be switched on or off separately. From the middle position of a transmitter, outputs 1 and 2 react in one direction (more than 1,5ms) and outputs 3 and 4 in the other direction (less than 1,5ms). Each output can be loaded with max. 4A, whereby the sum of all load currents should not exceed 6A. Ideal switching module for switching 4 different light functions, for example.

Available immediately, delivery time: 1-4 days

Product number: 3022

€ 18,00 *
Speed ​​controller THOR 4, up to 15V max. 4A 100% forward, 100% reverse
Speed ​​controller THOR 4, up to 15V max. 4A 100% forward, 100% reverse
1x THOR 4 speed controller, up to 15V max. 4A 100% forward, 100% reverse. With BEC 1000mA. 15x12x4,5mm, CTI product. Micro forward-reverse controller for 5-10 cells and 4 amps continuous output Low-drop voltage regulator. Not suitable for brushless motors! The controller is particularly suitable for small slow-running motors in mini and micro models. But also ideal for RB35 motors. Dimensions: width: 15mm, depth: 12mm, height: 4mm Weight with cables: 6 grams Continuous current: 4 amps, short-term: 12 amps BEC: 1000 mA (up to 8 cells) RDSon: 0,09 ohms Servo cable/connector: Graupner/JR Detailed instructions are included.

Available immediately, delivery time: 1-4 days

Product number: 3020

€ 18,00 *
Speed ​​controller THOR 15 Li, up to 16V max.16A 100% forward, 1 pc.
Speed ​​controller THOR 15 Li, up to 16V max.16A 100% forward, 1 pc.
1 speed controller THOR 15 Li, up to 16V max.16A 100% forward, 100% reverse. With BEC 1000mA. 24x20x7mm, CTI product. With LiPo monitoring. Forward/reverse controller for 2-3 LiPo cells for scale models with Bühler motors and standard motors up to size 540.Width: 24mm, depth: 20mm, height: 6mmWeight with cables: 14gContinuous current: 16 ampsShort-term: 50 ampsRDSon: 0,015 OhmBEC: 5 Volt 1000mAh servo cable/plug: Graupner/JR Detailed instructions are included. Undervoltage detection and reduction When switched on, the THOR15Li detects whether a 2-cell or 3-cell LiPo battery is connected. Accordingly, the reduction limit is set to either 6 volts or 9 Volt is set. If the battery voltage falls below this limit then only 1/4 of the target speed is passed on to the motor. So a significant reduction in the ride that everyone will notice and can drive "home" with this reduced ride. Not for brushless motors. Motors suitable!

Available immediately, delivery time: 1-4 days

Product number: 5473

€ 21,00 *
1x speed controller THOR 4s, up to 15V max. 4A 100% forward,
1x speed controller THOR 4s, up to 15V max. 4A 100% forward,
1x speed controller THOR 4s, up to 15V max. 4A 100% forward, 100% reverse. Self-learning. With BEC 1000mA. 15x12x4,5mm, CTI product. Self-learning means:When switched on, the controller recognizes the current control position in the transmitter and assumes this position as the current ZERO POSITION!Micro forward-backward controllerfor 5-10 cells and 4 amps continuous outputLow-drop voltage regulator.Not suitable for brushless motors!The controller is particularly suitable for small slow-running motors in mini and micro models.But also ideal for RB35 motors.Dimensions: width: 15mm, depth: 12mm, height: 4mmWeight with cables: 6 gramsContinuous current: 4 amps, short-term: 12 ampsBEC: 1000 mA (up to 8 cells)RDSon: 0,09 ohmServo cable/connector: Graupner/JRDetailed instructions are included.

Available immediately, delivery time: 1-4 days

Product number: 3087

€ 18,00 *
Throttle controller THOR 15 HCs, up to 16V max.16A
Throttle controller THOR 15 HCs, up to 16V max.16A
1x THOR 15 HCs speed controller, up to 16V max. 16A, self-learning, 100% forward, 100% reverse. With BEC 1000mA. 24x20x7mm, CTI product. Self-learning means: When switched on, the controller recognizes the position of the encoder in the transmitter and takes this as the current zero position! Not suitable for brushless motors!

Available immediately, delivery time: 1-4 days

Product number: 3049

€ 21,00 *
Tip:
Servonaut S22 speed controller for trucks and functional models
Servonaut S22 speed controller for trucks and functional models
1x Servonaut S22 speed controller for trucks and functional models/vehicles. Speed ​​controller for 7,2 to 12V and 20A/5min at 16 kHz clock frequency. BEC 5V/3A. 2 switching outputs, 700mA each for brake light and reversing light, control output for Servonaut sound modules, including instructions, dimensions approx. 70x38x9mm. For functional models of size 1:16 to 1:8. Further development of the well-known S20 controller! Better resolution and sensitivity: 450 speed levels! The inertia of a heavy vehicle is realistically reproduced. Integrated protective functions: - Overload protection - Overtemperature protection - Undervoltage protection Also suitable for bell-shaped armature motors! Seamless EMF braking, no loss of control when driving downhill. Delay-free change forward/backward. Powerful 5V/3A receiver supply with large cooling surface. Diagnostic LEDs.Undervoltage shutdown for 6 or 10 cells NiMH and 2 or 3 cells LiPo.Automatic zero setting with start-up protection.Instructions for this article are available for download. Downloading is free! (except for your online costs).NEW article - follow-up article to the S20!

Available immediately, delivery time: 1-4 days

Product number: 9182

€ 104,99 *
THOR14LF speed controller, up to 20V max. 14A 100% forward 100% reverse
THOR14LF speed controller, up to 20V max. 14A 100% forward 100% reverse
1x THOR14LF speed controller, up to 20V max. 14A 100% forward, 100% reverse. Without BEC system! 23x15x7mm, CTI product. This item replaces the previous THOR 14 (6866)! This controller does NOT have a BEC system. It is therefore ideal as a secondary controller for pumps or other drives. Also perfectly suited for ramp and support drives. It must be powered by the receiver. The BEC voltage must be between 5 and 5,5 volts DC. Not suitable for brushless motors! Technical data: Maximum voltage: 20 volts. RDSON is 25 milliohms. Maximum current: 14 amps. 1mm² silicone cables are attached for battery and motor connections. Dimensions: 23x15x7 mm

Available immediately, delivery time: 1-4 days

Product number: 11689

€ 18,00 *
Tip:
Racing battery pack with 5000 series Sub-C cells, 7,2V. 6 cells
Racing battery pack with 5000 series Sub-C cells, 7,2V. 6 cells
1x racing battery pack with SUB-C cells, 7,2V 6 cells, 5000mAh with Tamiya plug. SUB-C cells. Dimensions approx. 137x47x25mm. Approx. 430 g, NiMH, R3x2 design. With silicone wires! This battery pack fits in the standard battery compartment of all Tamiya tractors! 5000mAh - for extremely long driving fun!!! The matching charging cable can be found under item number 1867 - here in the shop.

Available immediately, delivery time: 1-4 days

Product number: 9680

€ 45,99 *
SFR-1 sound drive controller from BEIER. Especially for trucks
SFR-1 sound drive controller from BEIER. Especially for trucks
1x SFR-1 sound speed controller from BEIER. Specially developed for trucks. 16 switching outputs for lighting. Can be set using the Sound Teacher SFR software. WITH CD-ROM/DVD or USB stick Speed ​​controller for DC brush motor, sound module and light control module in one! Also suitable for bell-armature motors! Specially developed for trucks. Powerful BEC with 5,6V 3A. Optional load control, cruise control and brake function. Can be set in great detail using the -Sound Teacher SFR-. The speed controller is characterized by its high sensitivity. The controls are very realistic and dynamic and guarantee absolute driving fun. Thanks to a wide range of setting options, the speed controller can be easily and individually adapted to the most diverse model requirements and driving characteristics. All settings are made using the -Sound Teacher SFR- - the convenient configuration program from BEIER-Electronic. The model's lighting can be connected directly to the speed controller using the 16 light outputs. The speed controller has an extra output for connecting the IR transmitter diode for the light module SM-IR-16-2. (Article 9810). Features: - Supply voltage: 6-18V - Max. Motor current 30 A (continuous) 60 A (short-term) - PWM clock frequency 20 or 40 kHz - 16 switching outputs for the lighting - Powerful BEC 5,6 V 3 A - 6 proportional inputs (throttle, steering, control, sound, light) - 2 proportional outputs (servo outputs) - Failsafe in the event of reception interference (engine stop) - Start-up protection when switched on - Battery voltage monitoring - Temperature monitoring - Short-circuit protection for motor output stage - Short-circuit protection for BEC - Short-circuit protection switching outputs Can be selected via Sound Teacher SFR: - Load control on/off - Cruise control on/off - Braking function on/off - Handbrake function on/off - Selection of battery type: LiPo/ other type - Learning function (setup) for throttle channel on/off Can be set via Sound Teacher SFR (K-USB-2 required!):-Firmware update-Diagnosis-Channel inversion-Shutdown of undervoltage monitoring-Reduction of reversing speed-Selection of PWM clock frequency-Activation/setting of mass inertia-Activation/setting of steering inertia-Setting of handbrake hardness-Setting of throttle curve-Configuration of switching outputs (output type, brightness, xenon)-Configuration of light switch-Configuration of control channelThe speed controller is delivered with a standard configuration and is ready for use!-Battery connection 2x 1,5qmm, 25cm long, DEANS T-plug-Motor connection 2x 1,5qmm, 25cm long-2x servo cable for connection to receiver, 30cm long-Connection cable for loudspeaker, 25cm long-Cable for standby switch or volume potentiometer, 25cm-1x ribbon cable 40cm for connecting the switching outputs-Micro SD card (4GB) plus adapter-DVD with Sound-Teacher SFR-1 or USB stick (from 8/2024)-Manual SFR-1technical data:-Dimensions: 80 x 47 x 23 mm-Weight: 86g

Available immediately, delivery time: 1-4 days

Product number: 10974

€ 264,95 *
1 15 Fahrregler THOR HC until 15V max.18A 100% forward
1 15 Fahrregler THOR HC until 15V max.18A 100% forward
1 speed controller THOR 15 HC, up to 15V max.18A 100% forward, 100% reverse. With BEC 1000mA. 24x20x7mm, CTI product. Not suitable for brushless motors!

Available immediately, delivery time: 1-4 days

Product number: 3019

€ 21,00 *
Speakers 4 Ohm 50x50x22 mm
Speakers 4 Ohm 50x50x22 mm
1x speaker 4 Ohm 50x50x25 mm. 88gr. Suitable for USM-RC-2, 10 watts, music output. Small design. LS-4R-10W-50 A suitable speaker housing: Article 9848 (not included).

Available immediately, delivery time: 1-4 days

Product number: 9847

€ 15,95 *
Servo patch cable 10cm
Servo patch cable 10cm
1x servo patch cable 10cm. Both sides JR connector. 0,14qmm. BEIER-Electronic Accessories.

Available immediately, delivery time: 1-4 days

Product number: 9811

€ 2,84 *
Switching module for braking and reversing light 2 outputs with max
Switching module for braking and reversing light 2 outputs with max
Switching module for brake and reversing light 2 outputs with max. 4 A, for parallel connection to a speed controller. PS2BR, 13x15x2,5mm, CTI product.

Available immediately, delivery time: 1-4 days

Product number: 3021

€ 18,00 *
Connection terminal AKL-8 BEIER-Electronic. Simple wire
Connection terminal AKL-8 BEIER-Electronic. Simple wire
Connection terminal for switching outputs For easy wiring of BEIER UFR-1230, SFR-1, UFR-1230D. AKL-8. Scope of delivery:10-pin connection terminal with spring contacts10-pin flat edge cable, color-coded, approx. 20cm long, with post couplings on both sidesOperating instructions

Available immediately, delivery time: 1-4 days

Product number: 10986

€ 13,95 *
1 15 throttle THOR HF until 16V max.16A, with brake
1 15 throttle THOR HF until 16V max.16A, with brake
1 THOR 15 HF speed controller, up to 16V, max. 16A, 100% forward, 100% reverse. 18kHz. With 1000mA BEC. With brake function. 24x20x6mm, CTI product. Special feature of the HF controller: Clocking at 18 kHz, allowing for sensitive control and eliminating the whistling noise in the motor. A self-learning LiPo undervoltage detection reduces the motor speed at 9 or 6 volts. Voltage: up to 16 volts Current: up to 16 amps Undervoltage detection with regulation High-frequency clocking at 18 kHz (no whistling noise from the motor) BEC: 1 amp Dimensions: 24 x 20 x 6 mm Not suitable for brushless motors! For the first time, these THOR controllers are equipped with a brake to prevent a vehicle from rolling uncontrollably downhill on a slope. Another special feature is the high clocking at 18 kHz. This allows for more sensitive control, and the whistling noise in the motor is no longer audible. A self-learning LiPo undervoltage detection system reduces the motor speed at 9 volts or 6 volts. The integrated BEC supply can power the receiver and a small servo. This BEC voltage is short-circuit and temperature-protected. But be careful: This means that if the battery overheats, this voltage will shut down, leaving the receiver temporarily without power! Therefore, conduct extensive tests or use an external BEC, such as an X-BEC. When switched on, the THOR15HF detects whether a 2-cell or 3-cell LiPo battery is connected. Accordingly, the cut-off limit is set to either 6 volts or 9 volts. If the battery voltage drops below this limit, only 1/4 of the target speed is transmitted to the motor, resulting in a significant reduction in speed that everyone will notice, allowing them to drive "home" with this reduced speed. Of course, the controller can also be operated with NiMH or lead-acid batteries. Control range: the zero point is fixed at 1,5 ms pulse width, which corresponds exactly to that of today's standard RC systems. Before and after this point, i.e., stick forward/backward, the motor rotates continuously forward/backward, each up to the maximum speed. Caution: Before the first run, the range of the RC system should be checked. If the controller is defective, the motor may start even when the receiver is turned off!

Available immediately, delivery time: 1-4 days

Product number: 9764

€ 26,00 *
1x Servonaut MF8 mini-speed controller for adjusting and
1x Servonaut MF8 mini-speed controller for adjusting and
1x Servonaut MF8 mini speed controller for actuators and auxiliary drives. WITHOUT BEC! Load capacity up to 8A. Frequency 4kHz. Voltage 6-12V (5-10 NiMH cells). Dimensions: 50x19x7mm. Integrated protection functions: -Overload protection -Overtemperature protection -Undervoltage protection -Automatic zero setting, no start-up protection For drive systems, the S10 or S22 controllers are recommended. These controllers have BEC and connections for brake and tail lights. Instructions are available for downloading this article. Downloading is free! (except for your online costs). NEW ITEM - replaces the previous MFR!

Available immediately, delivery time: 1-4 days

Product number: 9191

€ 33,59 *
1x page correct chain mixer
1x page correct chain mixer
1x side-correct chain mixer. This mixer allows you to control any tracked vehicle with 2 forward/backward controllers using a joystick. In contrast to the simple V-mixer, this mixer controls both drive motors in a side-correct manner. It therefore allows you to control any tracked vehicle with two forward/backward controllers using a simple joystick. This mixer is also ideal for operating boats with multiple screw drives. Whether you have 2 or more screws, this mixer allows you to perform turning maneuvers much more tightly and precisely. Suitable for both forward/backward and pure forward drives. Features: 2x receiver input (throttle & steering) and 2x output to the controller (motor left & motor right) programmable zero point programmable mixing of 20-100% 2 modes selectable: side-correct and V-mixer Dimensions 34x34x5 mm Weight 15g with cables

Available immediately, delivery time: 1-4 days

Product number: 9776

€ 23,95 *
1 spring steel clevis V, 3,0mm thread
1 spring steel clevis V, 3,0mm thread
1 spring steel clevis V, 3,0mm thread.

Available immediately, delivery time: 1-4 days

Product number: 1520

€ 0,82 *
1x relay pole reversal switch with end position switch-off. Failsa
1x relay pole reversal switch with end position switch-off. Failsa
1x relay reversing switch with end position shutdown. Failsafe function. For motor polarity reversal with end position detection. Switching capacity max. 10A, 1-40V. Features: - programmable switch-on point - connections for two end position switches, module stops the motor as soon as the end position is reached - negligible power consumption - possible switching capacity per switch 10 A / 1-40 Volt - screw connections - failsafe - dimensions 43 x 34 x 21 mm - weight 40 g with Graupner servo cable When connected to a free channel on the joystick, the connected motor is in the middle position. Can of course be operated with a free channel on the joystick or an ON/OFF/ON switch on the transmitter. Lever up: the motor turns in one direction Lever down: the motor turns in the other direction Lever in the middle position: the motor stands still. There is a practical holder for this module: item 11956.

Ready to ship in 5 days, delivery time 1-4 days

Product number: 9856

€ 22,94 *
Limit switch module 2 with 2 limit switch inputs. For intermediate
Limit switch module 2 with 2 limit switch inputs. For intermediate
1x Limit Switch Module-2 with 2 limit switch inputs. For plugging into the controller control cable. 20x8x3mm, CTI product. ESM-2. A range of limit switches is available for this module, differing primarily in their size (which requires different space). The function of each switch is identical. You can find the following suitable items in our shop: 634363447140719812138

Available immediately, delivery time: 1-4 days

Product number: 7722

€ 17,99 *
1 Truck sound module SM3 with speed and
1 Truck sound module SM3 with speed and
1 truck sound module SM3 with engine noise depending on speed and driving situation. Compressed air noise, horn, starting, stopping. 7,2-12V 3 watts at 8 ohms. A free receiving channel required! Successor sound module to the previous SMT. Half the size of the predecessor, space-saving installation. 5 engine types selectable! Previous engine types of the SMT and SMX! Reverse warning tone, adjustable idle and full throttle speed. 5 setups for US or European trucks. Mini volume control for hidden installation on the model. Starter and horn are operated using the joystick or button/switch with 3 positions on the transmitter.Wavetable sound synthesis.Can be combined with many speed controllers from other manufacturers (forward-backward controller without braking range).Power is supplied from the drive battery.With battery connector (BEC).Optional sound controller SM-EQ available as an accessory.Dimensions approx. 55x28x13mm.Instructions are available for downloading this article. Downloading is free! (except for your online costs).Recommended loudspeakers with 7,2V supply voltage:Article with 8 ohms: 7028, 9851, 9852, 9854.Recommended loudspeakers with 12V supply voltage:Article 8962.

Available immediately, delivery time: 1-4 days

Product number: 8961

€ 147,99 *
Servo controller travel tip delay. Moves a servo with it
Servo controller travel tip delay. Moves a servo with it
Servo controller travel-tip-delay. Moves a servo with adjustable speed and adjustable servo travel. CTI product. This servo controller is a true all-round talent! The 2 adjustment potentiometers allow the speed of the servo movement (delay) to be adjusted, as well as the reduction of the servo travel. The servo controller travel-tip-delay can be operated directly on the receiver output or via a PS4x module!

Available immediately, delivery time: 1-4 days

Product number: 6057

€ 18,00 *
Data Cable K-USB 2
Data Cable K-USB 2
1x data cable K-USB-2. For live diagnosis, transfer of sound projects. Connection via USB interface. The data cable is NOT required. With the data cable K-USB-2, the sound modules SFR-1, SFR-1-D, USM-HL-2, light modules LM-xx, USM-RC-2 and USM-RC-3 as well as the speed controllers UFR-1230 /UFR-1230-D can be connected to a PC via a USB interface.The data cable has two functions:1. Live diagnosisWith the help of the data cable, the sound teacher can receive and display the current diagnostic data live (e.g. position of the proportional channels, status of the inputs and outputs, nautic values, etc.). This option is very helpful when troubleshooting.Note:The sound modules SFR-xx, USM-HL-2 and USM-RC-x can also save the diagnostic data on the SD card. This recorded data can be viewed without a data cable using the Sound Teacher's diagnostic function. However, the saved values ​​have the disadvantage that you only see the "past" and not what is currently happening (live) on the module. 2. Transferring the configurations and sounds from the Sound Teacher/Drive Teacher to the SFR-x, USM-HL-2, USM-RC-x and UFR-1230/UFR-1230-D modules If a sound or a setting in the configuration is to be changed, the SD card must normally be unplugged from the module, plugged into the PC's card reader, the project data saved to the SD card using the Sound Teacher and the card plugged back into the sound module. However, if changes are made frequently, which occur particularly when the device is first put into operation or when testing new functions, unplugging and plugging can quickly become annoying. Using the data cable, all changes can be easily transferred to the sound module without having to keep re-plugging the SD card. However, transferring sounds using the data cable is relatively slow! A sound that is 10 seconds long takes around 60 seconds to transfer using the data cable. Therefore, transferring long sounds or large, new projects using the data cable is only advisable to a limited extent. The data cable is not absolutely necessary for setting up the sound module, but is often very helpful if you want to work a lot with the various setting options of the sound module.

Available immediately, delivery time: 1-4 days

Product number: 9822

€ 23,95 *
%
HS-645MG servo (Hitec). Powerful standard servo. Dimensions
HS-645MG servo (Hitec). Powerful standard servo. Dimensions
1 HS-645MG servo (Hitec). Powerful standard servo. Dimensions: 40x20x37mm. 55g. Metal gears. 2 ball bearings. 77/96 Ncm. 0,24s/60°. Universal/JR connector. Powerful standard servo. Ideal as a steering servo. Scope of delivery: 1 servo, 5 control discs/levers, mounting hardware. Technical data: Gear teeth: 24T, Ball bearings: yes, Waterproof: no, Torque at 4,8V: 8 kgcm, Torque at 6,0V: 10 kgcm, Gears: Metal, Motor type: Brushed, Electronics type: Analog

Available immediately, delivery time: 1-4 days

Product number: 7968

€ 37,09 * € 37,10 * (0.03% saved)
SFR-1 sound drive controller from BEIER. Especially for trucks
SFR-1 sound drive controller from BEIER. Especially for trucks
SFR-1 Sound Speed ​​Controller from BEIER. Specially developed for trucks. 16 switching outputs for lighting. Can be adjusted using the Sound-Teacher SFR software. No CD-ROM/DVD/USB stick required. Speed ​​controller for DC brushed motors, sound module, and light control module in one! Also suitable for coreless motors! Specially developed for trucks. Powerful BEC with 5,6V 3A. Optional load control, cruise control, and braking functions. Can be adjusted in great detail using the Sound Teacher SFR. The speed controller is characterized by its high sensitivity. The control is very realistic and dynamic, guaranteeing absolute driving pleasure. Thanks to its diverse setting options, the speed controller can be easily and individually adapted to the most diverse model requirements and driving characteristics. All settings are made using the Sound-Teacher SFR – the convenient configuration program from BEIER Electronic. The model's lighting can be connected directly to the speed controller via the 16 light outputs. The speed controller has an extra output for connecting the IR transmitter diode for the SM-IR-16-2 light module (item 9810). Features: - Supply voltage: 6-18V - Max. Motor current 30 A (continuous) 60 A (short-term) - PWM clock frequency 20 or 40 kHz - 16 switching outputs for the lighting - Powerful BEC 5,6 V 3 A - 6 proportional inputs (throttle, steering, control, sound, light) - 2 proportional outputs (servo outputs) - Failsafe in case of reception interference (motor stop) - Start-up protection when switched on - Battery voltage monitoring - Temperature monitoring - Short-circuit protection for the motor output stage - Short-circuit protection for the BEC - Short-circuit protection for switching outputs. Selectable via Sound Teacher SFR: - Load control on/off - Cruise control on/off - Brake function on/off - Handbrake function on/off - Selection of battery type: LiPo/other type - Learning function (setup) for the throttle channel on/off. Adjustable via Sound Teacher SFR (K-USB-2) required!): -Firmware update -Diagnosis -Channel inversion -Shutdown of undervoltage monitoring -Reverse speed reduction -Selection of PWM clock frequency -Activation/adjustment of mass inertia -Activation/adjustment of steering inertia -Adjustment of handbrake hardness -Adjustment of throttle curve -Configuration of the switching outputs (output type, brightness, xenon) -Configuration of the light switch -Configuration of the control channel The speed controller is delivered with a standard configuration and is ready for use! -Battery connection 2x 1,5 mm², 25 cm long, DEANS T-connector -Motor connection 2x 1,5 mm², 25 cm long -2x servo cables for connection to receiver, 30 cm long -Connection cable for loudspeaker, 25 cm long -Cable for standby switch or volume potentiometer, 25 cm -1x ribbon cable 40 cm for connecting the switching outputs -Micro SD card (4 GB) plus adapter Data:-Dimensions: 80 x 47 x 23 mm-Weight: 86g

Available immediately, delivery time: 1-4 days

Product number: 10977

€ 254,95 *
1x speed controller THOR14LFs, up to 20V max. 14A 100% forward, 100%
1x speed controller THOR14LFs, up to 20V max. 14A 100% forward, 100%
1x THOR14LFs speed controller, up to 20V max. 14A 100% forward, 100% reverse. Without BEC system! SELF-LEARNING. 23x15x7mm, CTI product. Successor to the THOR14s (6867)!Self-learning means:When switched on, the controller recognizes the current position of the encoder in the transmitter and takes this as the current zero position!This controller must be supplied with power from the receiver as it does NOT have a BEC system!Not suitable for brushless motors!Technical data:Maximum voltage: 20 volts.RDSON is 25 milliohms.Maximum current: 14 amps.1qmm silicone cables are attached for battery and motor connection.Dimensions: 23x15x7 mm

Ready to ship in 5 days, delivery time 1-4 days

Product number: 11939

€ 18,00 *
Memory switch PS4b with 4x 4A output 4x on / off function
Memory switch PS4b with 4x 4A output 4x on / off function
Memory switch PS4b with 4x 4A output 4x on / off function on 1 RC-channel outputs as 2 Blinker.Max. Voltage 20V 13x15x2,5mm, CTI product

Available immediately, delivery time: 1-4 days

Product number: 3023

€ 18,00 *
1x throttle AS-12 / 35RW Truck EVO III. 100% pre / rev
1x throttle AS-12 / 35RW Truck EVO III. 100% pre / rev
1x speed controller AS-12/35RW Truck EVO III. 100% forward, 100% reverse. Max. 35A. With BEC max. 3A / short 5A. 18kHz clock speed! 6-18V input voltage. 5-14 cells NiMH or 2-4 LiPos. Dimensions: 36x33x11mm. 33gr. Version without cruise control! Max. current: 35A (50A short). Autosetup, failsafe, LED monitor, LiPo detection, undervoltage protection, intelligent soft polarity reversal, 2 different handbrake modes. Overtemperature shutdown. Outputs for brake and reversing light with 1A each. Handbrake The AS12-35RW Truck Evo III has two different handbrake modes. In normal mode (green LED flashes) the brake slowly switches on in the zero position and ensures that the model stops but does not. This mode is recommended for most applications, especially for street trucks. For crawlers and four-wheel drive trucks that like to stop on a slope, it is recommended to select the brake mode (red LED flashes). In this mode, the brakes are applied very quickly and thus prevent the model from rolling away on the slope. But be careful: This mode can brake a model at full speed very quickly! Performance features: - 5-14 cells / 2-4 Lipos / 12 Volt lead (with Lipo monitoring 3,4V per cell) - Automatic cell count detection in Lipo mode (at approx. 3,4 volts per cell), the maximum power is limited to 25% and the controller signals that the battery is empty by jerking the motor) - 35 A continuous, 50 A short-term - Switching BEC up to 14 cells / 4s Lipo. 3A continuous up to 5A short-term - two different braking modes can be programmed (street truck / crawler). - Lipo monitoring can be switched on / off - Overtemperature shutdown, if the controller gets too hot it regulates back to max. 25% power. - Full HF 18 kHz output stage over the entire control range. NO motor whistling and extremely sensitive control. - Motor-friendly polarity reversal through speed-dependent polarity reversal time with brake. The braking time is calculated using an algorithm. (In the lower speed range the polarity is reversed immediately; at high speeds the controller brakes the motor gently so that the batteries and motor are protected from high current peaks.) - Handbrake function. When the throttle is at 0, the vehicle is first braked gently, then the handbrake is pulled.- Perfect failsafe (receiver signal is constantly checked) LED shows when the reception signal is lost.- Motor beep acknowledgement (for programming and for the OK message when connecting the battery).- Start-up protection (the controller only starts operating when the throttle is at 0. This prevents the motor from accidentally starting). If there is no RC signal, the vehicle stops.- Super-sensitive logarithmic control behavior (new evaluation system.- Two outputs for brake and reversing lights, each with a load of 1A, switch to ground.- 2,5 sqmm highly flexible connection cableDimensions 36 x 33 x 11 mmWeight 33 g

Available immediately, delivery time: 1-4 days

Product number: 9775

€ 66,95 *
Speed ​​controller 4HF potentiometer. This controller is a Stro
Speed ​​controller 4HF potentiometer. This controller is a Stro
Speed ​​controller 4HF potentiometer. This speed controller is a current measuring controller. With BEC (only for receiver supply). 17x17x6mm, CTI product. The 4HF potentiometer measures the current while the motor is running with a measuring resistor. If the current is higher than the maximum current set on the potentiometer, the software switches the motor off and indicates this with a red LED for control purposes. This protects the mechanics, motor and electronics in the event of overload or blocking operation. The motor can only start again after the transmitter stops the motor or steers it in the other direction.Technical data: Maximum driving voltage: 15V Dimensions: 17x17x6mm Battery and motor connection: 0,25qmm silicone Zero point: fixed at 1,5 microseconds Forward/backward: continuously variable up to maximum speed Areas of application:The HF4 potentiometer can be used universally for all applications where limit switches are not required.Examples: electric cylinders spindle drives loading ramps extendable vehicle supports extendable landing wheels and frames

Ready to ship in 5 days, delivery time 1-4 days

Product number: 12324

€ 36,00 *
%
1 ball head 5x3mm, total length 12mm, brass. M3 thread
1 ball head 5x3mm, total length 12mm, brass. M3 thread
1 ball head 5x3mm, total length 12mm, brass. M3 thread, thread length 5mm. Suitable for 5mm open ball sockets.

Available immediately, delivery time: 1-4 days

Product number: 8095

€ 0,79 * € 5,89 * (86.59% saved)
%
1x standard servo CS-3 with JR connector. Dimensions: 38,5x19x32m
1x standard servo CS-3 with JR connector. Dimensions: 38,5x19x32m
1x standard servo CS-3 with JR connector. Dimensions: 38,5x19x32mm. 4,8-6V voltage. Actuating torque at 4,8V: 31Ncm. Actuating time approx. 0,17sec./60°. Weight 39 g. Accessories: 2 rudder levers and screws.

Available immediately, delivery time: 1-4 days

Product number: 8851

€ 10,95 * € 11,49 * (4.7% saved)
1x memory switch PS4aT with 4x 4A output 2x
1x memory switch PS4aT with 4x 4A output 2x
1x memory switch PS4aT with 4x 4A output, 2x on/off function plus 2x tip-on function on 1 RC channel. Max voltage 20V 13x15x2,5mm, CTI product.

Available immediately, delivery time: 1-4 days

Product number: 3024

€ 18,00 *
1x Servonaut MFX mini-speed controller for adjusting and
1x Servonaut MFX mini-speed controller for adjusting and
1x Servonaut MFX mini speed controller for actuators and auxiliary drives or servo motors. Load capacity up to 10A. Frequency 16kHz. Voltage 6-12V (5-10 NiMH cells). Dimensions: 50x19x7mm. Integrated protection functions: -Overload protection -Overtemperature protection -Undervoltage protection -Diagnostic LED -Intelligent zero setting, no start-up protection -Can be used as universal servo electronics with adjustable control characteristics. -For servo operation, an additional potentiometer with 2kOhm or 5kOhm is required (NOT included!). No controller whistling (16KHz clocking) Instructions are available for downloading this article. Downloading is free! (except for your online costs). NEW ITEM - replaces the previous MFR!

Available immediately, delivery time: 1-4 days

Product number: 9181

€ 57,69 *
1x 2-channel switch (2x Memory). The max. 2A / 20V
1x 2-channel switch (2x Memory). The max. 2A / 20V
1x 2-channel switch (2x memory). 2 consumers can be switched on/off separately with 1 RC channel. Switching capacity per output max. 2A/ max. 20V. e.g. for lighting, headlights, fog horn, etc. Works with a free proportional channel or a 3-position switch on the transmitter. The 2-channel switch is particularly suitable for complex lighting with LEDs or bulbs, as 2 different functions can be operated independently of one another with just one channel. The RC transmitter does not need to be changed. Performance features: 2 separately and independently switchable switching functions with just one RC channel. Parallel operation on the servo is possible Negligible power consumption Possible switching capacity per switch 2 A / 0-20 Volt 2 powerful SMD-FETs Dimensions 26 mm x 11 mm x 5 mm Weight 9 g with cables Operation: In the following example, the module is connected to a channel with a vertical joystick. Channel 1: Move the joystick up and back to the 0 position. Channel 1 is switched on. Channel 2: Move the joystick down and back to the 0 position. Channel 2 is switched on. To switch off the respective channel, repeat the process!

Available immediately, delivery time: 1-4 days

Product number: 9778

€ 16,95 *
1x plastic ball joint, 5mm ball, for M3, ball bore
1x plastic ball joint, 5mm ball, for M3, ball bore
1x plastic ball joint, 5mm ball, for M3, ball bore 3mm, 27mm total length. Head diameter 7,3mm. 1 piece. Ball head height: 4,2mm.

Available immediately, delivery time: 1-4 days

Product number: 3796

€ 2,23 *
%
Servo HS-40 (Hitec). Analog nano servo 8,6mm wide
Servo HS-40 (Hitec). Analog nano servo 8,6mm wide
1 Servo HS-40 (Hitec). Analogue nano servo. Dimensions: 20x8,6x17mm. 4,8gr. Nylon gear. 6 / 7,6Ncm. 0,12s / 60 °. Uni / JR plug. Power is supplied with 4 different servo arms.

No longer available

Product number: 8845

€ 12,50 * € 13,90 * (10.07% saved)
Details
1x throttle AS-12 / 6RW Easy with cables. 100% back /
1x throttle AS-12 / 6RW Easy with cables. 100% back /
1x AS-12/6RW Easy speed controller with cables. 100% forward, 100% reverse. Max. 6A. Without BEC. 18kHz clocking! 6-15V input voltage. 5-12 cells NiMH or 2-3 LiPos. Dimensions: 20x17x5mm. 6gr. Version without cruise control! Max. current: 6A (10A short). Failsafe, no LiPo monitoring. Intelligent soft polarity reversal. Performance features: - 5-12 cells / 2-3 LiPos / 12 Volt lead - 6 A continuous, 10 A short-term - Full HF 18 kHz output stage over the entire control range. NO motor whistling and extremely sensitive control. - Motor-friendly polarity reversal thanks to speed-dependent polarity reversal time. Speed ​​range is immediately reversed (at high speeds the controller brakes the motor gently so that the battery and motor are protected from high current peaks.) - perfect failsafe (receiver signal is constantly checked) LED shows when the reception signal is lost. - Motor beep acknowledgement (for programming and for the OK message when connecting the battery). - Start-up protection (the controller only starts operating when the throttle stick is at 0. This prevents the motor from starting accidentally). If there is no RC signal, the vehicle stops. - super-sensitive logarithmic control behavior (new evaluation system. - 2,5 sqmm highly flexible connection cable Dimensions 20 x 17 x 5 mm Weight 6 g

Available immediately, delivery time: 1-4 days

Product number: 9867

€ 24,94 *
%
CARSON Reflex Stick Multi Pro LCD 2,4GHz Remote Control
CARSON Reflex Stick Multi Pro LCD 2,4GHz Remote Control
CARSON Reflex Stick Multi Pro LCD 2,4GHz remote control with 14 channels. 14-channel transmitter, 14-channel receiver and manual. With 15 model memories. Reflex Stick Multi Pro LCD - Professional, modern and technically high-quality 14-channel remote control system with 15 model memories for universal use in many RC vehicles and ships. 14 channels can be controlled independently via 2 joysticks and 10 switches (4x buttons / 4x step switches / 2x rotary potentiometers), for example functions such as light / sound, horn, cable winch, support legs, water pump and fire monitor.The REFLEX STICK Multi Pro 14 Channel LCD System is fully compatible with the MFC 01/03 and DMD unit from TAMIYA. Scope of delivery:14 channel 2.4 GHz transmitter, 14 channel 2.4 GHz receiver and multilingual manual.Required accessories:4x Mignon AA cells. Mignon battery set article 9492Recommended accessories:500503060 Reflex 6 / 14Ch Switch 2 (2x2.5A, max. 16V)500503061 Reflex 6 / 14Ch Switch 4 (4x2.5A, max. 16V)500503062 Reflex Switch 2/4 power distributor500606073 Plug-in charger (item 10723)Transmitter charging cable: item 9673500501544 Receiver500609042 Mignon battery set (AA)Technical data:- Operating voltage transmitter 4,8 - 6 V (4 AA cells)- 2.4G FHSS system (Frequency HoppingSpread Spectrum)- 2.4G servo reverse (reversal of the direction of rotation) and trim function for channels- 4x buttons ON/OFF/ON, 4x switches ON/OFF/ON, 2x rotary potentiometers- Power supply for the receiver 4,8 - 6 V- Plug system Graupner J/R- Dual Rate channel 1-4 (servo travel limitation)- EPA channel 1-4 (servo travel limitation)- ABS function channel 1-4 (Stutter brake)- EXP function channel 1-4 (exponential)Technical details:- 14 controllable channels- 15 model memories- Includes charging socket- 100% compatible with TAMIYA MFC 01/03 and DMD unit- Blue illuminated LC displayIt is not possible to bind several receivers at the same time with this system.Receivers that can be used with this system:Article 11259, 4-channel receiverArticle 12422, 4-channel receiver, waterproofArticle 12421, 5-channel receiverArticle 12420, 5-channel receiver, waterproof

Available immediately, delivery time: 1-4 days

Product number: 10326

€ 125,00 * € 159,99 * (21.87% saved)
Single-cell battery Mignon Eneloop 2000mAh without soldering tag
Single-cell battery Mignon Eneloop 2000mAh without soldering tag
Single AA Eneloop 2000mAh rechargeable battery cell without solder tabs, NiMH, HR-3U, AA size. 1 piece.

Ready to ship in 5 days, delivery time 1-4 days

Product number: 4399

€ 4,22 *
Flat speaker 8 Ohm / 5W. For 12V operation. 90x40x14mm
Flat speaker 8 Ohm / 5W. For 12V operation. 90x40x14mm
1x flat speaker 8 Ohm/5W. For 12V operation. 90x40mm. Depth 14mm. For SMT, SMX and SM7 at 12V and SM3 at 7,2V. Loud89. Dimensions approx. 90x40x14mm. Loudspeaker boxes (not included) are available for this: Item 10826 or 11283 (for high roof) or 10828 (for AROCS high roof).

Available immediately, delivery time: 1-4 days

Product number: 9854

€ 13,70 *
1x mini speaker Visaton 8 Ohm for 12V operation. 50 x
1x mini speaker Visaton 8 Ohm for 12V operation. 50 x
1x Visaton 8 Ohm mini speaker for 12V operation. 50 x 50 mm. Depth 22 mm. Rated power handling 4 W. Loudness 85. Music power handling 10 W. Dimensions approx. 50 x 50 x 25,5 mm. Optionally available (not included): Matching speaker cabinet: Items 9336, 8908 (for high roof), 12893. 5 cm full-range speaker with a square basket, soft surround, and lightweight special cone. Balanced frequency response from 250 Hz and crisp high-frequency reproduction with good omnidirectional characteristics.

Available immediately, delivery time: 1-4 days

Product number: 7028

€ 14,90 *
Servo patch cable 30 cm
Servo patch cable 30 cm
1x servo patch cable 30 cm. Both sides JR servo connector. 0,14qmm. BEIER-Electronic Accessories.

Available immediately, delivery time: 1-4 days

Product number: 9812

€ 2,50 *
Racing battery pack with SUB-C cells, 7,2V 6 cells, 5300mAh
Racing battery pack with SUB-C cells, 7,2V 6 cells, 5300mAh
1x racing battery pack with SUB-C cells, 7,2V 6 cells, 5300mAh with Tamiya plug. SUB-C cells. Dimensions approx 137x47x25mm. about 450 gr., NiMH, construction L2x3. With silicone strands!

No longer available

Product number: 11028

€ 42,00 *
Details
ESC THOR 4x3, up to 15V max.4A 100% forward/backward
ESC THOR 4x3, up to 15V max.4A 100% forward/backward
1x THOR 4x3 speed controller, up to 15V max.4A 100% forward, 100% reverse. With BEC 1000mA. 30x15x4,5mm, CTI product. 3 identical controllers in one module! 3 micro forward-reverse controllers in one module!for 5-10 cells and 4 amps continuous outputLow-drop voltage regulator.Not suitable for brushless motors!The controller is particularly suitable for small slow-running mini and micro models.But also excellent for RB35 motors.Dimensions: width: 30mm, depth: 15mm, height: 4mmWeight with cables: 11 gramsContinuous current: 4 amps, short-term: 12 ampsBEC: 1000 mA (up to 8 cells)RDSon: 0,09 ohmsServo cable/connector: Graupner/JRDetailed instructions are included.

Available immediately, delivery time: 1-4 days

Product number: 11547

€ 40,00 *
Plastic ball joint, 6mm ball, for M3 ball bore 3mm,
Plastic ball joint, 6mm ball, for M3 ball bore 3mm,
Plastic ball joint, 6mm ball, for M3 ball bore 3mm, 27mm total length, head diameter 9,5mm with hexagon. 1 piece.

Available immediately, delivery time: 1-4 days

Product number: 3795

€ 2,20 *
1x 2 channel switch (2x 10A) / 2 relay. 2 consumers could
1x 2 channel switch (2x 10A) / 2 relay. 2 consumers could
1x 2-channel switch (2x 10A) / 2 relays. 2 consumers can be switched on/off separately with 1 RC channel. Switching capacity per output max. 10A each/ max. 40V. e.g. for lighting, headlights, fog horn, etc. Works with a free proportional channel or a 3-position switch on the transmitter. The 2-channel switch is particularly suitable for complex lighting with LEDs or bulbs, as 2 different functions can be switched independently of each other with just one channel. The RC transmitter does not need to be changed. Features: 2x separate SWITCH function with just one RC channel Switchable memory function for each function can be switched on via DIP. Parallel operation on the servo possibleNegligible power consumptionPossible switching capacity per switch 10A / 0-40 Volt2 relay levels with changeover contactsScrew connectionsLED function controlOperating voltage: 4,8-6VDimensions 40mm x 34mm x 21mmWeight 40g with servo cableOperation:In the following example, the module is connected to a channel withvertical control stick.Channel 1: Move the control stick up and hold itChannel 1 is switched on. (Touch function) Channel 2: Move the control stick down and hold itChannel 2 is switched on. (Touch function)To switch off the respective channel, move the control stick to the neutral position.When the MEMORY function is switched on, the channel remains switched on until the control stick is AGAIN moved to the same position.There is a practical holder for this module: Article 11956.

Available immediately, delivery time: 1-4 days

Product number: 11250

€ 20,94 *
1x Servonaut S10 speed controller for small trucks and...
1x Servonaut S10 speed controller for small trucks and...
1x Servonaut S10 speed controller for small trucks and functional models/vehicles. Speed ​​controller for 7,2 to 12V and 10A/5min at 16 kHz clock frequency. BEC 5V/1A. 2 switching outputs, 20mA each for brake light and reversing light. Incl. instructions, dimensions approx. 55x19x7mm. For small functional models. Integrated protective functions: - Overload protection - Overtemperature protection - Undervoltage protection Also suitable for bell-shaped armature motors! Seamless EMF brake, no loss of control when driving downhill. Delay-free changeover forwards/backwards. BEC: 5V/1A receiver supply. Diagnostic LEDs. Undervoltage shutdown for 6 or 10 cells NiMH and 2 or 3 cells LiPo. Automatic zero setting with start-up protection. Instructions are available for downloading this article. Downloading is free! (except your online costs).NEW article - improved follow-up article to the MFR!

Available immediately, delivery time: 1-4 days

Product number: 9192

€ 62,50 *
X-BEC 5,7-35V input voltage, output 5,5V until max. 8A
X-BEC 5,7-35V input voltage, output 5,5V until max. 8A
X-BEC 5,7-35V input voltage, 5,5V output, up to max. 8A possible, 3A continuous current. CTI product.

Available immediately, delivery time: 1-4 days

Product number: 5112

€ 10,00 *
Tip:
1x Servonaut M24, speed controller with lighting system for trucks
1x Servonaut M24, speed controller with lighting system for trucks
Servonaut M24 speed controller with lighting system for trucks and functional models/vehicles. Speed ​​controller for 7,2 to 12V and 20A/5 min. at 16 or 32 kHz clock frequency, BEC 5,3V/4A, lighting system with 6 switching outputs each 700mA, including instructions, dimensions approx. 43x13x80mm. Equally suitable for conventional motors and bell-armature motors. Instructions are available for downloading for this article. Downloading is free! (except for your online costs).

Available immediately, delivery time: 1-4 days

Product number: 9766

€ 198,99 *
THOR 4-HF Titan1/6 speed controller, for 12V. 100% forward, 100%
THOR 4-HF Titan1/6 speed controller, for 12V. 100% forward, 100%
THOR 4-HF Titan1/6 speed controller, for 12V. 100% forward, 100% reverse. With BEC (only for receiver supply). 15x12x4,5mm, CTI product. The Thor 4 HF Titan 1 is a "shutdown controller" with a brake specifically for operating the CTI Titan cylinders.The controller automatically switches off the Titan cylinder when the end positions are reached when extending and retracting, or when a load of approx. 6-6,5 kg is exceeded.It is equipped with a brake that immediately stops the cylinder even under high load and ensures that it is not possible to "push it on" when the cylinder is at a standstill (handbrake).The controller controls the motor speed continuously forwards and backwards and can be started again in both directions after an overload shutdown.Operating voltage: 12 volts (10 NiMh cells or 3 LiPo)Dimensions: 15x12x4,5 mmBattery and motor connection: 0,25qmm silicone cableBEC supply: 5 volts(the 5 volt supply can also be used for a receiver. However, other servos should not be operated via this as this will affect the current measurement (shutdown) (can)Use: exclusively for the operation of ONE titanium cylinder.

Ready to ship in 5 days, delivery time 1-4 days

Product number: 10653

€ 24,00 *
1 horn for function models. Realist- ischer horn sound for
1 horn for function models. Realist- ischer horn sound for
1 horn for functional models. Realistic horn sound for trucks or construction machines (e.g. excavators). Can be connected directly to the receiver output. Approx. 15x17mm, with M5 thread. Servo cable JR. Electronic horn with the sound of a truck horn. It makes sense to control it via a BUTTON on the transmitter! But of course any other control device (joystick, slider, etc.) can also be used for control. The power supply comes directly from the receiver no additional power supply necessary!

Available immediately, delivery time: 1-4 days

Product number: 7020

€ 35,00 *
%
CS-9 MG power servo with JR connector. Dimensions: 40x20x38mm
CS-9 MG power servo with JR connector. Dimensions: 40x20x38mm
1x power servo CS-9 MG with JR connector. Dimensions: 40x20x38mm. 4,8-6V voltage. Actuating torque at 4,8V: 85Ncm. Actuating time approx. 0,1sec./60°. Weight 50 g. Accessories: 2 rudder levers and screws. This powerful servo is equipped with ball bearings and metal gears. It is also splash-proof and is therefore ideal as a steering servo in vehicles that sometimes move in damp environments!

Available immediately, delivery time: 1-4 days

Product number: 7939

€ 27,99 * € 29,99 * (6.67% saved)
%
Battery Pack racing with 5000er cells F5x2 12V 10 cells AMP
Battery Pack racing with 5000er cells F5x2 12V 10 cells AMP
1x battery racing pack with 5000 cells, 12V 10 cells, SUB-C, with AMP socket, approx. 16cm strands 1,5qmm, approx. 715g, F5x2, 115x46x44mm, NiMH cells. X-Cell cells.

Available immediately, delivery time: 1-4 days

Product number: 9966

€ 79,00 * € 94,90 * (16.75% saved)
Memory switch PS4o with 4x 4A output 4x on / off function
Memory switch PS4o with 4x 4A output 4x on / off function
Memory switch PS4o with 4x 4A output 4x on/off function on 1 RC channel max. voltage 20V. 1,2,3, or 4x tip. 13x15x2,5mm, CTI product

Available immediately, delivery time: 1-4 days

Product number: 5189

€ 18,00 *
Volume potentiometer mini. BEIER electronic module. For setting
Volume potentiometer mini. BEIER electronic module. For setting
1x Mini volume potentiometer. BEIER Electronic Module. For adjusting the volume. Wire length: 20 cm. Resistance: 100 kOhm. For SFR-1, USM-RC-2, USM-RC, and USM-xx. Mini version.

Ready to ship in 5 days, delivery time 1-4 days

Product number: 11798

€ 6,95 *
1x truck sound module SM7 with turbocharger 5 engines, 5
1x truck sound module SM7 with turbocharger 5 engines, 5
1x truck sound module SM7 with turbocharger 5 engines, 5 horns to choose from compressed air noise, siren, starting, stopping, gearshift noise. 7,2-12V. 7 watts. Successor to the SMX module! Sound module for truck models - successor to the proven SMX, significantly smallerDynamic turbocharger sound in a class of its own - even closer to the originalDriving situation-dependent engine sound with turbochargerIgnition, starter and shutdown noise, reversing warning tone5 truck horns, compressed air noises, siren5 engines: Actros V6, Scania V8, TGA in-line cylinder, DAF in-line 6-cylinder, Scania in-line 6-cylinderMulti-channel sound synthesisTurbocharger, compressed air, warning tone and switching noises can be set and adjusted separately in volume via Servonaut CARD (available as an accessory)Switching noises and warning tone with K15/30/40/60, reversing warning tone and brake-synchronized compressed air also available with M20+/M24 and S20/S22, function limited with speed controllers from other manufacturersStarter and horn can be operated optionally via switching inputs (Multiswitch) or a receiver channelSound module can be connected directly to an auxiliary motor or servo motor to simulate a power take-off noiseSmall separate volume control ideal for hidden installation on the modelFor 7,2V to 12V loudspeakers from 4 ohmsPower is supplied from the drive batteryWith battery plug (matching counterpart is BECB)Can be combined with SM+ for additional soundsOptional sound control SM-EQ available as an accessoryDimensions approx. 65 mm x 35 mm x 12 mmInstructions are available for download for this article. Downloading is free! (except for your online costs).Recommended loudspeakers with 7,2V supply voltage:Article 6049.Recommended loudspeakers with 12V supply voltage:Article 7028 or 9854.

Available immediately, delivery time: 1-4 days

Product number: 9066

€ 198,99 *