Rear lights

PAGE

Boards for 7 chamber taillights 7,2V. 1 pair (1x left,

Circuit boards for 7-chamber rear lights 7,2V. 1 pair (1x left, 1x right), trailer, fitted with SMD LEDs, common plus pole, 5 light functions, BLUE identification. Necessary resistors are integrated! Matching article 1905 - 7-chamber rear light. The insulated individual connection wires are color-coded: Wire length approx. 18cm. Red = common plus pole White = rear light Black = brake light Gray = right indicator Yellow = left indicator Green = reversing light Blue = rear fog light When using these lighting circuit boards, the following light functions are possible.

Available immediately, delivery time: 1-4 days

Product number: 3104

€ 37,00 * € 39,90 * (7.27% saved)

Subscriptions

7-chamber rear light unit (1 pair) without board. Dimensions

7-chamber rear light unit (1 pair) without circuit board. Overall dimensions: 32x12x7mm The base body is chrome-plated on the inside. (500907037) Instructions can be downloaded here. Suitable lighting circuit boards in SMD technology can be found under item number 3103 (for 12V) or 3104 (for 7,2V) or 3105 (for 4,8V). Also the lighting set for Carson trailers, item 7786. When using the lighting circuit boards (not included), the following lighting functions are possible. (suitable control required).Tail lightBrake lightReverse lightIndicator/hazard warning lightsRear fog light

Available immediately, delivery time: 1-4 days

Product number: 1905

€ 15,99 * € 19,49 * (17.96% saved)

Subscriptions

4-chamber taillight unit (1 pair) without bracket

4-chamber rear light unit (1 pair) without holder, 32x9x11mm (LxHxD) (220982). The holes for the lighting units have a diameter of approx. 2,8mm. To use standard 3mm LEDs, these may need to be drilled out a little. Replacement light lenses are available under the item numbers: 6459 (red) 6460 (orange) 6461 (clear) Complete LED boards for installation are also available under item numbers 8347/8348! Now available again from stock!

Available immediately, delivery time: 1-4 days

Product number: 2626

€ 12,90 * € 13,20 * (2.27% saved)

Subscriptions

Boards for 7-chamber rear lights 12V. 1 pair (1x left,

Circuit boards for 7-chamber rear lights 12V. 1 pair (1x left, 1x right), trailer, equipped with SMD LEDs, common plus pole, 5 light functions, RED identifier. Necessary resistors are integrated! Matching article 1905 - 7-chamber rear light. The insulated individual connection wires are color-coded: Wire length approx. 18cm. Red = common plus pole White = rear light Black = brake light Gray = right indicator Yellow = left indicator Green = reversing light Blue = rear fog light When using these lighting circuit boards, the following light functions are possible.

Available immediately, delivery time: 1-4 days

Product number: 3103

€ 36,20 *

Subscriptions

3-chamber rear light unit (1 pair) around with

3-chamber rear light unit (1 pair) round with red/orange light discs, ALU base body 11mm diameter. Slot width for LEDs 2,2mm! 500907039. Item number 5641 (12V) or 3817 (7,2V with series resistor if necessary) is suitable as a light source. Both bulbs can be used lying down for the indicator light (middle) or standing up for the brake and tail light (top and bottom). For those who like low power consumption, we offer SMD LEDs with soldered wires under item numbers 6341 (red) and 6340/6342 (white)! These LEDs can be used almost anywhere in model making due to their very small size of just 2x1,25mm. In addition, the annoying fiddling around of soldering the wires to these tiny things is no longer necessary! Fastened using a central M2 screw. 4 holes with a 2mm diameter for the wires to pass through. Tip: We recommend that you first mount the red light discs on the aluminum base body and only then carefully separate the outer spray edge. This can prevent the thin connecting bridge between the red parts from breaking. The light discs are available separately as replacement items under item number 3407 if required.

Available immediately, delivery time: 1-4 days

Product number: 3240

€ 17,99 * € 19,49 * (7.7% saved)

Subscriptions

1x license plate panel (illuminated) with stop buffers

1x license plate plate (illuminated) with stop buffers (rubber), SMD LEDs and 1 reflective license plate of your choice in WDC or Tamiya size. Suitable for operation at 7,2 - 15V! Dimensions:Overall width 47mmHeight 10mmDepth 6mm at the lighting fixturesScope of delivery:License plate plate made of rubber with warm white SMD LEDs on both sidesSeries resistors (1kOhm) already solderedThe resistor is soldered into the PLUS line.1 reflective CUSTOM license plate2 rubber buffersFastening material for license plate plate and rubber bufferWhen ordering, please specify the text for the license plate of your choice, the federal state and the scale (Wedico or Tamiya)!Maximum area for license plate: 39 x 9,5mm.

Made individually for you - 1-4 days delivery time

Product number: 6436

€ 24,10 *

Subscriptions

configure now

6-chamber taillight unit (1 pair) without circuit board. total

6-chamber rear light unit (1 pair) without circuit board. Total width 38mm, 11mm high, 6mm deep. Width of the light unit 26,5mm. (500907038) The base body is chrome-plated on the inside. Matching lighting circuit boards in SMD technology can be found under item number 3233 (for 12V) or 3234 (for 7,2V). When using the lighting circuit boards (not included), the following lighting functions are possible: Tail light Brake light Reversing light Indicator/hazard warning light Fog tail light

Available immediately, delivery time: 1-4 days

Product number: 3134

€ 17,99 * € 19,49 * (7.7% saved)

Subscriptions

1 pair 3 1 +-chamber tail lights. Without holder. 32x9x11mm

1 pair of 3+1 chamber tail lights. Without bracket. 32x9x11mm (LxHxD) (220986). Scope of delivery:2x 3-chamber housing2x 1-chamber housing2x orange lens4x red lens2x clear lens

Available immediately, delivery time: 1-4 days

Product number: 9040

€ 12,90 * € 13,20 * (2.27% saved)

Subscriptions

1x aluminum sleeve 11mm diameter 4,5mm long with hole 7,6mm,

1x aluminum sleeve 11mm diameter 4,5mm long disc with bore 7,6mm, with red light. zBfür taillights, brake lights, fog lights. Mounting diameter 9mm.

Ready to ship in 5 days, delivery time 1-4 days

Product number: 4991

€ 3,50 *

Subscriptions

License plate holder, black, Variante1 with SMD-LEDS, white

License plate holder variant 1. 7-12V. Dimensions: 48x12x6mm, black. Made of ABS. Installation: Glue or screw with 2mm countersunk head. Scope of delivery: License plate holder, black, made of ABS. 2x SMD LED, cold white with enamelled copper wire. 2x series resistor for 7,2-12V. The black enamelled copper wire is the MINUS pole (cathode). It does not matter which cable the resistor is soldered into. It is only important that 1 resistor is used per LED.

Available immediately, delivery time: 1-4 days

Product number: 11477

€ 7,95 *

Subscriptions

Taillight housing with lens red / yellow / red 12mm

Taillight housing with red / yellow / red lens. 12mm outside diameter. Base body without chamber separations. Suitable for equipping with single SMDs.

Available immediately, delivery time: 1-4 days

Product number: 12303

€ 3,65 *

Subscriptions

3-chamber tail lights light slices around (1 pair)

3-chamber tail lights light slices around (1 pair) red / orange approx 11mm diameter Spare part for article number 3240. Delivery: 2 2 yellow and red parts).

Available immediately, delivery time: 1-4 days

Product number: 3407

€ 9,98 *

Subscriptions

MB Actros / Arocs rear light board. LH6MB of Servonaut

MB Actros/Arocs rear light board. The new LH6 boards from Servonaut automatically adapt to the battery voltage and are therefore suitable for 7,2-12V. Does not fit Arocs 3348. Item 11047 fits here. 7 or 8 LEDs per side and a combination of light guides, color and diffuser discs, which are included in the scope of delivery, ensure even and complete illumination of the chambers in the rear lights. The LH6 boards can be combined with all common lighting systems that switch minus, i.e. work with a common positive pole. - for 7.2 to 12 volts, no conversion necessary when changing to 12V - 5 light functions: indicator, parking light (dimmed), brake light, rear fog and reversing light - good optics thanks to 2x7 LEDs and included light guides, diffuser and color discs - high-quality 100cm long cable with PTFE insulation - suitable for Actros/Arocs and Servonaut M20+/M24/ML4/LA10/K40 - universally suitable for all lighting systems with a common positive pole - Scope of delivery: 2 boards (1x left, 1x right), light guide, diffuser - Illustration shows assembled rear light with original Tamiya parts (not included)

Available immediately, delivery time: 1-4 days

Product number: 10305

€ 38,29 *

Subscriptions

3-chamber rear light unit (1 pair) around with

3-chamber rear light unit (1 pair) round with red/orange lens, ALU base body 17,5 mm diameter (216405). Matching bulbs (6V/50mA) can be found under item number 3817! Replacement lens set: item 9892.

Available immediately, delivery time: 1-4 days

Product number: 3562

€ 17,50 * € 17,90 * (2.23% saved)

Subscriptions

1 circuit board license plate light for 7,2-14V. Suitable

1 circuit board license plate lighting for 7,2-14V. Suitable for lighting article 1904 (not included). No reverse polarity protection included. Red/black wires approx. 45cm long. 500907381 Fixing hole spacing = 28mmScope of delivery:1 circuit board with 2 LEDs and series resistor, wires 45cm long.The circuit board MUST be attached INSULATED on the back! Risk of short circuit!Wire color red = plusWire color black = minus

Available immediately, delivery time: 1-4 days

Product number: 9080

€ 16,99 * € 18,99 * (10.53% saved)

Subscriptions

1x license plate panel (illuminated) with stop buffers

1x license plate plate (illuminable) with stop buffers (rubber), (207001). Overall width 47mm. (Plate) 10mm high, 6mm deep on light holders. (500907034) Item 9080 (not included) is suitable for lighting. A complete set with SMD LEDs and individual DESIRED LICENSE PLATE is also available under item number 6436!

Available immediately, delivery time: 1-4 days

Product number: 1904

€ 12,99 * € 13,49 * (3.71% saved)

Subscriptions

Lighting glasses flat, red + red and orange 15x 15x

Illumination lenses flat, red + orange 15x red and 15x yellow. Diameter 9mm. (148).

Available immediately, delivery time: 1-4 days

Product number: 4643

€ 14,80 * € 14,95 * (1% saved)

Subscriptions

1x taillights light slices round, bright. 11mm diameter

1x taillights light discs around, clearly. 11mm diameter. In keeping with the 1 3557-chamber tail light.

Available immediately, delivery time: 1-4 days

Product number: 4120

€ 3,38 *

Subscriptions

1x aluminum sleeve 11mm diameter 4,5mm long with hole 7,6mm,

1x aluminum sleeve 11mm diameter, 4,5mm long with 7,6mm hole, for inserting a 9mm lens. e.g. for tail lights, indicators, brake lights, etc. Mounting diameter 9mm

Available immediately, delivery time: 1-4 days

Product number: 4985

€ 2,50 *

Subscriptions

Boards for 6 chamber taillights 7,2V. 1 pair (1x li., 1x

Circuit boards for 6-chamber rear lights 7,2V. 1 pair (1x left, 1x right) equipped with special SMD LEDs, common positive pole, 5 light functions including marker LED for towing vehicle. Identification BLUE. Matching article 3134 - 6-chamber rear light. No series resistors are required with 7,2V supply voltage. Circuit board size 23x7,5mm. Strand length approx. 70cm. The insulated individual connection strands are color-coded: red = common PLUS pole white = tail light black = brake light gray = right indicator yellow = left indicator green = reversing light blue = rear fog light When using these lighting circuit boards, the following lighting functions are possible: See product videos!

Available immediately, delivery time: 1-4 days

Product number: 3234

€ 43,10 *

Subscriptions

1x aluminum sleeve 11mm diameter, 11mm long with hole for 3mm

1x aluminum sleeve 11mm diameter 11mm long with hole for 3mm LED, for inserting a 9mm Lens. zBfür rear lights, turn signals, brake lights, etc. mounting diameter 9mm.

Available immediately, delivery time: 1-4 days

Product number: 11868

€ 2,50 *

Subscriptions

1x taillights light slices round, red. 11mm diameter

1x taillights light slices round, red. 11mm diameter. Matching the 1-chamber tail light 3558.

Available immediately, delivery time: 1-4 days

Product number: 4121

€ 3,38 *

Subscriptions

Boards for 6-chamber rear lights 12V. 1 pair (1x left, 1x

Circuit boards for 6-chamber rear lights 12V. 1 pair (1x left, 1x right) equipped with special SMD LEDs, common plus pole, 5 light functions including marker LED for towing vehicle. Identification RED. Matching article 3134 - 6-chamber rear light. The insulated individual connection wires are color-coded: Wire length approx. 70cm. Red = common plus pole White = rear light Black = brake light Gray = right indicator Yellow = left indicator Green = reversing light Blue = rear fog light When using these lighting circuit boards, the following lighting functions are possible:

Available immediately, delivery time: 1-4 days

Product number: 3233

€ 43,10 *

Subscriptions

1x license plate plate with stop buffers (rubber)

1x license plate plate with stop buffers (rubber), (207001) AND circuit board! Overall width 47mm. (Plate) 10mm high, 6mm deep at light holders. Complete set with price advantage! A complete set with SMD LEDs and individual DESIRED LICENSE PLATE is also available under item number 6436!

Ready to ship in 5 days, delivery time 1-4 days

Product number: 9092

€ 27,99 * € 32,48 * (13.82% saved)

Subscriptions

4 red covers (rear light, red). 8mm diameter

4 red covers (rear light, red). 8mm diameter. Height with / without collar: 8 / 6mm. (5010).

Available immediately, delivery time: 1-4 days

Product number: 3570

€ 1,46 * € 1,60 * (8.75% saved)

Subscriptions

1-chamber tail light (1) Red round with Lens

1-chamber rear light (1 piece) red round with red lens, base body ALU 11mm diameter (207042) Delivery without light body. For reasons of space, we recommend the use of SMD LEDs: Article 9205 / 6341

Available immediately, delivery time: 1-4 days

Product number: 3558

€ 6,69 * € 7,60 * (11.97% saved)

Subscriptions

1-chamber tail light (1 piece), clear round with Lens

1-chamber rear light (1 piece), clear round with clear lens, ALU base body 11mm diameter. (207041). Delivery without light body. For reasons of space, we recommend the use of SMD LEDs: Article 9027 / 6340

Available immediately, delivery time: 1-4 days

Product number: 3557

€ 8,31 * € 8,90 * (6.63% saved)

Subscriptions

Boards for 4 chamber taillights 7,2V. 1 pair (1x li., 1x

Circuit boards for 4-chamber rear lights 7,2V. 1 pair (1x left, 1x right) equipped with 3mm LEDs, common positive pole (red), 4 light functions. (191585). Matching the 4-chamber rear light item 2626.4 Light functions:Tail light, cable color blackBrake light, cable color blueIndicator, cable color yellow (left), orange (right)Reverse light, cable color whiteCable lengths approx. 40cm.Comes with instructions.

Available immediately, delivery time: 1-4 days

Product number: 8348

€ 21,50 * € 21,90 * (1.83% saved)

Subscriptions

4 orange taillight covers, orange 8mm diameter

4 orange taillight covers, 8mm orange diameter. Height with / without collar: 8 / 6mm. (5009).

Available immediately, delivery time: 1-4 days

Product number: 3573

€ 1,59 * € 1,60 * (0.63% saved)

Subscriptions

1x taillights light discs around yellow. 11mm diameter

1x rear light lens, round. Yellow. 11mm diameter. Suitable for 1-chamber rear light 3559.

Available immediately, delivery time: 1-4 days

Product number: 4122

€ 3,38 *

Subscriptions

1x aluminum sleeve 11mm diameter 4,5mm long with hole 7,6mm,

1x aluminum sleeve 11mm diameter, 4,5mm long with 7,6mm hole, with clear lens. e.g. for reversing lights. Mounting diameter 9mm.

Ready to ship in 5 days, delivery time 1-4 days

Product number: 5588

€ 3,50 *

Subscriptions

Tip

Volvo FH16 backlight blanks. (1 pair) The new LH6 Plati

Volvo FH16 tail light boards. (1 pair) The new LH6 boards from Servonaut automatically adjust to the battery voltage and are therefore suitable for 7,2-12V. Only suitable for Tamiya Volvo FH16! A large number of LEDs per side and a combination of light guides and diffusers, which are included in the delivery, ensure even and complete illumination of the chambers in the tail lights. The LH6 boards can be combined with all common lighting systems that switch minus, ie work with a common positive pole. for 7.2 to 12 volts, no conversion necessary when changing to 12V extends the tail lights to 5 chambers, no drilling or sanding necessary 5 light functions: indicator, parking light (dimmed), brake light, rear fog light and reversing light dynamic indicators (2 steps) good optics thanks to lots of LEDs and included light guides, color and diffuser lenses high-quality 100cm long cable with PTFE insulation suitable for Volvo FH16 and Servonaut M20+/M24/ML4/LA10/K40 universally suitable for all lighting systems with a common positive pole Scope of delivery: 2 circuit boards (1x left, 1x right), light guide, diffuser lenses Attention small parts! Assembly requires some experience in model making Illustration shows assembled tail light with original Tamiya parts (not included) NOT suitable for connection to the MFCxx from Tamiya! Can be pre-ordered now.

Available immediately, delivery time: 1-4 days

Product number: 11471

€ 50,60 *

Subscriptions

1 4 pair-chamber tail lights (445) kit bracket