System equipment

KLB 8-500 expansion board. The expansion board

1x KLB 8-500 expansion board. The expansion board offers the possibility of expanding the light assistant by a further 8 outputs. Plug & Play solution. The module, which is only 21 x 26 mm in size, offers the possibility of expanding the light assistant by a further eight outputs - with a load capacity of up to 500 mA. It is simply connected to one of the EasyBus outputs of the light assistant and is thus automatically integrated into the system. The outputs of the expansion board offer exactly the same functionality as the outputs of the light assistant. - In addition to some effect lighting, all the usual lighting functions in the original are available: - combined front light (parking light, low beam, high beam, headlight flasher and fog light) - combined rear light (parking light, brake light, rear fog light) - American rear light (parking light, brake light, indicator) - daytime running light with automatic lowering when indicator is activated - cornering light - cornering light - reversing light - indicator, hazard warning light, American indicator - multi-flashing light - running light - rotating light - KnightRider In addition to the basic behavior of the individual outputs, the brightness, the switching on and off speed, as well as the switching on and off duration for flashing functions can also be set. Dimensions: 23x28x13mm Number of switching outputs: 8 Current load capacity per output: 500mA Voltage at the + output: BEC voltage (5-6V)LED resistor integrated: noPower supply: via bus (BEC of the speed controller)Max. own power consumption: 25mA

Available immediately, delivery time: 1-4 days

Product number: 9245

34,90 €

Subscriptions

Kraftwerk control pad Light & Sound. Control pad for all sends

Kraftwerk Light & Sound Control Pad. Control pad for all transmitters for a Kraftwerk lighting system. The pad connects to a free proportional channel on the transmitter and behaves like a normal joystick, meaning it doesn't use complex transmission signals like most multiswitches, making it compatible with any remote control transmitter. The Light & Sound control pad switches all lighting functions, the trailer supports, the tipper body, the fifth wheel coupling, and 11 additional functions (e.g., a rotating beacon), the gearshift, and two servos. It also features a "all on" and "all off" button for quick access. Dimensions: 78 x 33 mm. The pad is compatible with all remote control transmitters. It is important that the selected channel is a proportional channel, meaning a servo connected to the corresponding receiver output must be continuously variable. (Switching channels are unsuitable!) Ideally, the channel should be free, i.e., without any other control inputs (cross stick, linear controller, etc.) connected. Since new transmitters often no longer have expansion channels, an occupied channel can be used in an emergency, however, it must not be in use and must always be in the middle position (otherwise the functions will not work).

Available immediately, delivery time: 1-4 days

Product number: 11089

74,90 €

Subscriptions

KLB 8-20 expansion board. The expansion board

1x KLB 8-20 expansion board. The expansion board offers the possibility of expanding the light assistant by a further 8 outputs. Plug & Play solution. The module, which is only 15 x 28 mm in size, offers the possibility of expanding the light assistant by a further eight outputs - capable of handling up to 20 mA. It is simply connected to one of the EasyBus outputs of the light assistant and is thus automatically integrated into the system. The outputs of the expansion board offer exactly the same functionality as the outputs of the light assistant. - In addition to some effect lighting, all the usual lighting functions in the original are available: - combined front light (parking light, low beam, high beam, headlight flasher and fog light) - combined rear light (parking light, brake light, rear fog light) - American rear light (parking light, brake light, indicator) - daytime running light with automatic lowering when indicator is activated - cornering light - cornering light - reversing light - indicator, hazard warning light, American indicator - multi-flashing light - running light - rotating light - KnightRider In addition to the basic behavior of the individual outputs, the brightness, the switching on and off speed, as well as the switching on and off duration for flashing functions can also be set. Dimensions: 15x28x13mm Number of switching outputs: 8 Current load capacity per output: 20mA Voltage at the + output: BEC voltage (5-6V)LED series resistor integrated: yes (180 Ohm)Power supply: via bus (BEC of the speed controller)Max. own power consumption: 25mA

Available immediately, delivery time: 1-4 days

Product number: 10114

29,90 €

Subscriptions

BUS distributor. 1 to 6. This distributor allows you to...

1x BUS distributor. 1 to 6. With this distributor, the EasyBus outputs of the light assistants can be divided into a further 6 outputs. Plug & Play solution. With this distributor, the EasyBus outputs of the light assistants can be divided into a further 6 outputs. Connection cable with a length of approx. 15 cm.

Available immediately, delivery time: 1-4 days

Product number: 9255

4,90 €

Subscriptions

EasyBus replacement cable 30cm long, 1-sided with post coupling

EasyBus replacement cable 30cm long. 1-sided with post coupling. 1 side open wire ends.

Available immediately, delivery time: 1-4 days

Product number: 12168

2,80 €

Subscriptions

BUS - distribution. 1 to 6. 60cm. Power plant zone

BUS distributor. 1 to 6. 60cm With this distributor, the EasyBus outputs of the light assistants can be divided into 6 additional outputs. Plug&Play solution. Board size approx. 24x15mm.

Available immediately, delivery time: 1-4 days

Product number: 10448

6,90 €

Subscriptions

KLM 4/16 Light Assistant. The light assistant is the core component.

1x KLM 4/16 light assistant. The light assistant is the core component of a lighting system that can be expanded as required. Incl. Transmitting diode. Plug & Play solution. Core component of the lighting system, compatible with all sound modules, speed controllers and the Tamiya MFU-xx. The EasyBus lighting systems are equipped with different lighting boards, IR trailer lighting, etc. expandable.The PC software can be downloaded free of charge. No programming knowledge is required. The control can be customized down to the smallest detail. Technical data: - Dimensions 51x36x13 mm - 4 inputs (steering, throttle, channel 1, channel 2) - 2 servo outputs (steering servo, speed controller) - 5 bus outputs (for expansion modules) - 16 switching outputs with max. 500mA, freely configurable-1x USB socket (Micro-USB, for configuration)From April 2018 incl. Transmitter diodeWe are of course happy to configure the lighting system according to your ideas and also save them.The KLM 4/16 light assistant is the further development of the KLM 4/12-500. Compact design, easy operation and compatibility with the most common systems on the market are its main strengths. It is compatible with standard forward-reverse speed controllers (with or without a separate brake), with the cruise control controllers from Servonaut and all sound modules. The light functions can be controlled in a variety of ways; please refer to the manual for details. The module, which is only 52 x 36 x 13 mm in size, offers eight high-current outputs (500 mA each and eight switching outputs with integrated series resistors), four adjustable servo outputs, an infrared output, a USB socket that is only required for configuration and five bus outputs, via which the system can be expanded as required with additional switching, servo or motor functions. Standard assignment of the outputs:-Output 1 & 2: parking light & high beam & headlight flasher-Output 3 & 4: dipped beam-Output 5: left indicator-Output 6: right indicator-Output 7 & 8: tail light & brake light-Output 9: rear fog light-Output 10: reversing light-Output 11 & 12: speed camera-It is possible to select the behavior of each individual output completely independently and freely via PC and to configure it on a percentage basis. In addition to some effect lighting, you can choose from all the usual lighting functions in the original: -- combined front light (parking light, low beam, high beam, headlight flasher and fog light) -- combined rear light (parking light, brake light, -- American rear light (parking light, brake light, indicator) -- daytime running light with automatic lowering when the indicator is activated -- cornering light -- curve light -- reversing light -- indicator, hazard warning light, American indicator -- multi-flashing light -- running light -- rotating light -- KnightRider In addition to the basic behavior of the individual outputs, the brightness, the switching on and off speed, and the switching on and off duration for the flashing functions can also be set. How easy this is can be tested in advance using the demo mode of the free PC software ControlPanel. The module is connected to four channels of the receiver. In addition to gas and steering, two channels (K1 and K2) are used to control the lighting. Please refer to the manual for the different variants! During development, special attention was paid to ease of use. You do not need any electronic experience to use this system! You will find all the information you need in the included quick start guide! Scope of delivery: 1x KLM 4/16 light assistant, 1x IR transmitting diode, 4x servo patch cables 10cm

Available immediately, delivery time: 1-4 days

Product number: 10822

114,89 €

Subscriptions

EASYBUS adapter. 6-pin 15cm/JR connector. With this adapter

EASYBUS - adapter. 6-way 15cm/JR plug. With this adapter, the EasyBus lighting boards can be connected to the Beier, Brixl and Arduino systems. Plug & Play solution. For the use and control of Kraftwerk lighting boards, the following can be found in the Beier SFR-1 manual:From the Beier manual:The SFR-1 can also directly control the EasyBus lighting boards from Kraftwerk. This makes connecting the lighting much easier. The signal for the EasyBus lighting boards is available at slot X5/1 on the SFR-1. Attention: An EasyBus adapter with a suitable connection (servo plug) is required here!Please note: The EasyBus adapter is connected to connection X5/1 (Servo 1) on the SFR1. Therefore, servo output X5/1 can no longer be used to connect a servo!

Available immediately, delivery time: 1-4 days

Product number: 11382

9,90 €

Subscriptions

EasyBus lighting boards for 7 chamber taillights

EasyBus lighting boards for 7-chamber rear lights from Carson/Veroma. Suitable for the EasyBus system. The plug & play solution. The modules are each equipped with seven SMD LEDs and have an output with a series resistor on the back for free assignment (for example, for a marker light or license plate light). They are connected to the Easybus outputs of the light assistants. Simply plug in... Done! Each of the eight outputs can be changed as usual with the Kraftwerk ControlPanel and thus adapted to your own ideas. Attention: Since we use larger and brighter LEDs, the back panel of the lamp body must be removed. Unfortunately, this also eliminates the holes for the fastening screws, which is why the lamp bodies must be glued to the model.

Available immediately, delivery time: 1-4 days

Product number: 10349

59,80 €

Subscriptions

EasyBus lighting system semi-trailer KIEB 6 / 2 / 2

EasyBus KIEB 6/2/2 trailer lighting system for Tamiya or Carson trailers with Euro taillights. Installation tips & tricks: Tip 1: The KIEB 6/2/2 can be powered in three ways: via the battery connection, via a servo connection and the BEC of a connected speed controller, or via a bus output and the BEC of a connected KMB. Tip 2: After switching on, the red LED of the KIEB 6/2/2 will blink twice. The LED should then go out, provided an IR connection is established. If the red LED blinks irregularly, the receiver gain should be adjusted using the potentiometer. Tip 3: The IR transmitter's transmission can be checked by pointing the transmitting LED at a mobile phone camera. If a purple flicker is visible in the camera app, the diode is transmitting. Highlights & Details: Plug & Play solution (connect and drive); One motor output for trailer supports or spindle drives; Two freely adjustable servo outputs (e.g., for steerable trailing axle); Receives ALL information... all light functions and switching states... but also all proportional functions... up to 1.5m away or up to an angle of 90°; Lighting boards can be connected directly via EasyBus. Technical Data: Length (excluding pin length) 60mm; Width 40mm; Height 12.5mm; Voltage 4-5 cells (max. 8V); BEC 5V (1A); Switching outputs; Servo outputs 2; Motor outputs 2; EasyBus outputs 3; Bridgeable distance up to 1.5m; Maximum angle approximately 90°; Scope of delivery: KIEB 6/2/2 Item 10446; 2x Euro taillight board, Item 103492x machined Euro housing, item 10686 receiver diode, included in the KIEB. If the electronics are powered by a battery, we recommend (depending on available space) these items: Item 7110 with 4,8V, Item 11121 with 4,8V, Item 7823 with 4,8V, Item 7745 with 4,8V, Item 7549 with 6V, Item 6457 with 6V

Ready to ship in 5 days, delivery time 1-4 days

Product number: 11005

183,63 € 184,90 € (0.69% saved)

Subscriptions

KIEB 6 / 2 / 2 Infrared Receiver. Power plant plug & play solution

KIEB 6/2/2 Infrared Receiver. Plug & Play solution. Compatible with the EasyBus system. Power plant zone. The KIEB 6/2/2 receives all EasyBus information from the infrared transmitter. Plus: includes a 5 mm receiving diode, six switching outputs, two servo outputs, two motor outputs, and three EasyBus outputs. Technical data: Length (excluding pin length): 60 mm; Width: 40 mm; Height: 12.5 mm; Voltage: 4-5 cells (max. 8V); BEC: 5V (1A); Switching outputs: 6; Servo outputs: 2; Motor outputs: 2; EasyBus outputs: 3; Bridgeable distance: up to 1.5 m; Maximum angle: approximately 90°. The KIEB 6/2/2 is a KraftwerK infrared receiver with bus outputs and 6 switching, 2 servo, and 2 motor outputs. With the KIEB 6/2/2 infrared receiver, you can control the trailer supports and a tipper or ramp via the two integrated motor outputs. Doors, lift axles, or steering axles can be controlled via the two servo outputs. Auxiliary lighting or rotating beacons can be controlled via the switching outputs. Bus extensions (switching, servo, or motor extensions) can be connected to the three bus outputs as usual.

Available immediately, delivery time: 1-4 days

Product number: 10446

109,90 €

Subscriptions

EasyBus replacement cable 60cm long, 1-sided with post coupling

EasyBus replacement cable 60cm long. 1-sided with post coupling. 1 side open wire ends.

Available immediately, delivery time: 1-4 days

Product number: 12169

2,98 €

Subscriptions

1x XBSefect electronics, fully assembled 4 outputs each max.

1x XBSefect electronics, fully assembled, 4 outputs each with a maximum of 100mA, 15 different effects to choose from. BEC with 5V or external supply with 6 to 14 volts. Functions can be selected via remote control. RC flash electronics, fully assembled, 4 outputs each with a maximum of 100mA, 15 different effects to choose from (xenon light effect, flashing light, flashing light, permanent light and running light), BEC with 4,8 volts or external power supply of 6-14 volts, functions can be selected via remote control (3-way toggle switch or 3-way button with zero position in the middle 1-0-1) Size (lxwxh): approx. 35 x 22 x 15mm Weight: approx. 10 grams Contents: 1 electronic module 1 servo cable 1 jumper 1 power connection cable 1 instructions

Available immediately, delivery time: 1-4 days

Product number: 9575

32,74 €

Subscriptions

KIES infrared transmitter. Plug & Play solution

1x KIES infrared transmitter. Plug & Play solution. Incl. IR transmitter diode. Suitable for the EasyBus system. Technical data: - Dimensions 27,5x17x7,5 mm - Power supply via EasyBus - 1 servo output (adjustable) Scope of delivery: - 1x KIES infrared transmitter - 1x IR transmitter diode The infrared transmitter is simply plugged into a free connection on the EasyBus and is immediately ready for use. It not only transmits the light functions of EasyBus but also servo functions to the infrared receiver (not included). Items 9252 and 9253 are available as suitable infrared receivers.

Available immediately, delivery time: 1-4 days

Product number: 9254

34,90 €

Subscriptions

2-way distributor (Kingbus system) with 15cm cables.

2-way distributor (Kingbus system) with 15cm cables. This distributor can be used to expand the Kingbus system with new light modules. It works like a multiple socket in the home. This 2-way distributor is very suitable for connecting two rear light modules and the infrared transmitter module at the rear of a tractor unit. This means that only one twin cable leads to the front to the central module. This distributor is available with different cable lengths: 15, 30 and 50 cm.

Available immediately, delivery time: 1-4 days

Product number: 10937

8,50 €

Subscriptions

EasyBus lighting system KLM 4 / 16 TAMIYA MB Actros 3363

EasyBus Lighting System KLM 4/16 for Tamiya Mercedes-Benz Actros 3363. The lighting system for the Tamiya Actros 3363 features the new KLM 4/16, ready-to-install lighting circuit boards, and an integrated infrared transmitter. The lighting circuit boards are simply inserted into the light chambers from the rear and are held in place by a press fit. The system is controlled by a KLM 4/16, which is compatible with standard forward/reverse speed controllers (with or without separate brake), cruise control speed controllers, and all sound modules. The lighting functions can be controlled either with our control pad or in numerous other ways; please refer to the online manual for details. This starter set includes a complete lighting system for the Tamiya Mercedes-Benz Actros 3363 and consists of two front lighting circuit boards with pre-wired LEDs for the side indicators, underride guard, and marker lights, as well as a KLM 4/16 light assistant. The lighting circuit boards are connected directly to the KLM 4/16 connected and can also be configured via our Kraftwerk ControlPanel. Brightness, flashing speeds, and basic functionality (e.g., whether the high beam should be switched on the output) can be set separately for each output. Further information can be found under Highlights & Details. KLM 4/16 (4 servo inputs, 16 switching outputs, 5 bus outputs) Ready-to-install lighting boards Plug & Play solution (connect and drive) Compatible with all sound modules Compatible with all speed controllers Compatible with Tamiya MFU Expandable with various lighting boards Expandable with infrared for trailer lighting Customizable to the smallest detail via PC No programming knowledge required PC software available for free download Technical Data Power supply: via receiver power supply (BEC of the speed controller) Max. current consumption 20mA per device and 20mA per LED Front LEDs (per side):

Available immediately, delivery time: 1-4 days

Product number: 11003

269,89 €

Subscriptions

EasyBus Lighting System KLM 4 / 16 TAMIYA MAN TGX 18.540 / 26.54

EasyBus Lighting System KLM 4/16 for Tamiya MAN TGX 18.540 / 26.540 The lighting system for the TAMIYA MAN TGX 18.540 / 26.540 features the new KLM 4/16 controller, ready-to-install lighting boards, and an integrated infrared transmitter. The lighting boards are simply inserted into the light chambers from the rear and are held securely in place by a press fit. The system is controlled by a KLM 4/16 controller, which is compatible with standard forward/reverse speed controllers (with or without separate brake), cruise control controllers, and all sound modules. The lighting functions can be controlled either with our control pad or in numerous other ways; please refer to the online manual for details. This starter set includes a complete lighting system for the TAMIYA MAN TGX 18.540 / 26.540 and consists of two front lighting boards with pre-wired LEDs for the side indicators. Underride protection and marker lights, as well as a light assistant KLM 4/16. The lighting boards are connected directly to the KLM 4/16 and can also be configured via our Kraftwerk ControlPanel. Brightness, flashing speeds, but also the basic functionality (e.g., whether the high beam should be switched on the output) can be set separately for each output. You can find information on this under Highlights & Details KLM 4/16 (4 servo inputs, 16 switching outputs, 5 bus outputs) Ready-to-install lighting boards Plug & Play solution (connect and drive) Compatible with all sound modules Compatible with all speed controllers Compatible with Tamiya MFU Expandable with a wide variety of lighting boards Expandable with infrared for trailer lighting Customizable to the smallest detail via PC No programming knowledge required PC software available for free download Technical data Power supply: via receiver power supply (BEC of the speed controller) Max. Power consumption 20mA per device and 20mA per LED. Front LEDs (per side): yellow: 1x 3mm; white: 2x 3mm, 3x 5mm, 1x SMD; yellow wired: 1x 3mm; white wired: 1x 3mm. Ultra-bright high-performance LEDs. Additional outputs at the front: 3 with 180 Ohm resistors each. Rear LEDs (per side): red: 4x SMD 1206; yellow: 1x SMD 1206; white: 1x SMD 1206. Ultra-bright high-performance LEDs. Additional outputs at the rear: 1 each with 180 Ohm resistors. Scope of delivery: Light Assistant KLM 4/16, four ready-to-install lighting boards (2x front, 2x rear).

Available immediately, delivery time: 1-4 days

Product number: 11001

230,81 €

Subscriptions

4 distribution board (Kingbus system) with 15cm cables

4-way distributor (Kingbus system) with 15cm cables. This distributor can be used to expand the Kingbus system with new light modules. It works like a multiple socket in the home. This 4-way distributor is very suitable for connecting two rear light modules and the infrared transmitter module at the rear of a tractor unit. This means that only one twin cable leads to the front to the central module. This distributor is available with different cable lengths: 15, 30 and 50 cm.

Available immediately, delivery time: 1-4 days

Product number: 10875

9,50 €

Subscriptions

Power plant set with RS1 for Scania 770 S from Tamiya

Set consisting of RS1 and circuit boards for front and rear. Speed controller, lighting system, sound module in one incl. Complete lighting for Scania 770 S from Tamiya. Robust speed controllerThe speed controller can be permanently loaded with 25A and, thanks to the 32kHz control, is also suitable for bell-armature motors. It offers manual transmission support for up to four gears, a clutch function, handbrake, optional inertia simulation and a cruise control function, which does not work like the competition (stick deflection controls acceleration), but like the original: the throttle deflection controls the speed and the cruise control is activated by pressing a button. Pressing the button again or braking deactivates the cruise control.Extraordinary soundKraftwerK is once again setting standards in programmability. While the competition can only use a few sound snippets for the driving sound, KraftwerK can use as many as you like and it works as follows: First, the speed range is defined, e.g. 500 rpm immediately after starting and 2300 rpm when the engine is running out. Then sound snippets are stored for any number of areas and defined with base speed, minimum and maximum. At minimum the sound is faded in at a speed-adjusted level, at it is played at full volume and at a speed of 1:1, and up to maximum it is again adjusted to the speed and finally faded out. The snippets can and should of course overlap, which can create an ultra-realistic sound. In total there are three sound tracks: 2x acceleration and 1x deceleration. The first sound track is the normal driving sound, the second sound track can either be mixed proportionally as a load or switched. The third sound track is the delay sound and is automatically added when you release the joystick. If that's too complicated for you, you'll be pleased to know that 3 high-quality sounds are already included with the module. In the future there will also be a sound library with premium sounds that can be purchased for a few euros and downloaded via the ControlPanel and saved on your own module.Unlimited expandabilityKraftwerK's leading role in the field of RC bus systems is now fully evident in the RS1. The RS6 can be expanded as required via the 1 EasyBus outputs. Lighting boards, switching extensions, servo controls and much more can be controlled via the EasyBus. But the RS1 has one more special gimmick: on the upper side there are four individual sockets that are barely visible and can be used to plug in another module. The first module in this series is the BL8A, an 8A brushless controller designed for hydraulic pumps.Versatile connections / technical dataBattery (6 - 20V)Motor 25A, up to 32kHz, brush and bell-armature motor5 servo inputs or SUMD, IBUS, SBUS, CPPM5 servo outputs6 bus outputs8 switching outputs 500mA2 switching outputs 10AInfrared transmitter (diode included)SpeakerDimensions 63x44x28mmCharacteristics of the drive controllerOperating voltage 6-20VBEC 6V / 3ATimension frequency adjustable up to 32kHZClutch functionHandbrake functionManual transmission supportAdjustable inertia simulationAdjustable cruise controlProtection functions: battery undervoltage, motor short circuit, overtemperatureFunctions for servo outputsProportional functionProportional function directPropFunction switchedTwo positionsThree positionsFifth wheel plateTrailer supports MotorDump truck/tipper MotorRamp/Platform MotorManual transmissionSound featuresUnlimited number of sounds10-15 sounds that can be played simultaneouslyPlay modes: Touch, loop, once, permanent, random, stop pointsFormats: WAV, MP3 Usable sampling rate: All (automatic conversion to 44.100)Volume control: Potentiometer, via channel, via softwareSD card: max. 32 GB Features Lighting System Control: Light and sound control pad, user-defined channels, multi-switch Functions Hazard lights Left turn signal Right turn signal Sequential turn signal Parking lights Position lights Parking lights and low beam Parking lights and high beam Parking, low beam and high beam Parking lights and turn signals Position lights and turn signals Low beam Low beam and high beam High beam Fog lights Combined front lights Daytime running lights Taillight Brake lights Taillight, brake light Taillight, brake light and turn signal Taillight, rear fog light Rear fog light Combined rear lights Reversing lights Cornering lights / adaptive cornering lights Single switch Double switch Rotating beacon On/Off Strobe Sequential lights Knight Rider Aqua Effect Flash Proportional dimmer Recommended speaker: Item 9849.

Available immediately, delivery time: 1-4 days

Product number: 13185

439,80 €

Subscriptions

Machined housings for 7 chamber taillights (1 pair)

1 pair of machined housings for the 7-chamber rear lights from Veroma. Modified to fit the lighting boards 10349.

Available immediately, delivery time: 1-4 days

Product number: 10686

29,90 €

Subscriptions

Steerable kingpin for semi-trailers (Tamiya). For KingBus

Steerable kingpin for semi-trailers (Tamiya). For KingBus system. Measures the articulation angle of the tractor unit and semi-trailer. This kingpin measures the articulation angle/steering angle between the tractor unit and the semi-trailer. It is designed for installation in the Goldhofer low-loader semi-trailer from Veroma/Carson. Of course, it can also be used for custom builds! To mount this steerable kingpin (LKB) on the model, the hole for the pin must be drilled out larger. Otherwise, no further modifications to the semi-trailer are necessary. The connecting cables with plugs are designed for operation with the trailer module with additional functions (IRAM), item 11703. Technical data: Cable length: 150 mm, Potentiometer value: 5 kOhm, Connection: Cable with plug

Available immediately, delivery time: 1-4 days

Product number: 11702

59,00 €

Subscriptions

Power station zone Infrared transmitter diode

Kraftwerk-Zone infrared transmitting diode, 5mm round. For KLM 4/16.

Available immediately, delivery time: 1-4 days

Product number: 11286

9,90 €

Subscriptions

EasyBus lighting system KLM 4 / 16 for Tamiya Arocs 3348

EasyBus lighting system KLM 4/16 for Tamiya Mercedes-Benz Arocs 3348/4151. The lighting system for the TAMIYA Arocs 3348/4151 with the new KLM 4/16, ready-to-install lighting circuit boards, and integrated infrared transmitter. The lighting circuit boards are simply inserted into the light chambers from the rear and are held in place by a press fit. The system is controlled by a KLM 4/16, which is compatible with standard forward/reverse speed controllers (with or without separate brake), cruise control speed controllers, and all sound modules. The lighting functions can be controlled either with our control pad or in numerous other ways; please refer to the online manual for details. This starter set includes a complete lighting system for the Mercedes-Benz Arocs 3348/4151 from TAMIYA and consists of two front lighting circuit boards with wired LEDs for the side indicators, underride guard, and marker lights, as well as a KLM 4/16 light assistant. The lighting circuit boards are connected directly to the KLM 4/16 and can be controlled via this device. It can also be configured with our Kraftwerk ControlPanel. Brightness, flashing speeds, and basic functionality (e.g., whether the high beam should be switched on the output) can be set separately for each output. Information on this can be found under Highlights & Details KLM 4/16 (4 servo inputs, 16 switching outputs, 5 bus outputs) Ready-to-install lighting boards Plug & Play solution (connect and drive) Compatible with all sound modules Compatible with all speed controllers Compatible with Tamiya MFU Expandable with various lighting boards Expandable with infrared for trailer lighting Customizable down to the smallest detail via PC to match the prototype No programming knowledge required PC software available for free download Technical Data Power supply: via receiver power supply (BEC of the speed controller) Max. Power consumption 20mA per device and 20mA per LED. Front LEDs (per side): yellow: 1x 3mm; white: 2x 3mm, 1x 5mm; yellow wired: 2x 3mm; white wired: 1x 3mm. Ultra-bright high-performance LEDs. Additional outputs at the front: 3 with 180 Ohm resistors each. Rear LEDs (per side): red: 1x 3mm, 1x 5mm; yellow: 1x 5mm; white: 1x 3mm. Ultra-bright high-performance LEDs. Additional outputs at the rear: 2 each with 180 Ohm resistors. Scope of delivery: Light Assistant KLM 4/16, four ready-to-install lighting boards (2x front, 2x rear).

Ready to ship in 5 days, delivery time 1-4 days

Product number: 11264

219,00 € 224,90 € (2.62% saved)

Subscriptions

EasyBus replacement cable 80cm long, 1-sided with post coupling

EasyBus replacement cable 80cm long. 1-sided with post coupling. 1 side open wire ends.

Available immediately, delivery time: 1-4 days

Product number: 12170

2,98 €

Subscriptions

EasyBus Lighting System KLM 4 / 16 TAMIYA MB Arocs 3363

EasyBus KLM 4/16 lighting system for the Tamiya Mercedes-Benz Arocs 3363. This lighting system for the Tamiya Arocs 3363 features the new KLM 4/16 controller, ready-to-install lighting boards, and an integrated infrared transmitter. The lighting boards are simply inserted into the light chambers from the rear and are held securely in place by a press fit. The system is controlled by a KLM 4/16 controller, which is compatible with standard forward/reverse speed controllers (with or without separate brake), cruise control controllers, and all sound modules. The lighting functions can be controlled either with our control pad or in numerous other ways; please refer to the online manual for details. This starter set includes a complete lighting system for the Tamiya Mercedes-Benz Arocs 3363 and consists of two front lighting boards with pre-wired LEDs for the side indicators, underride guard, and marker lights, as well as a KLM 4/16 light assistant. They are connected directly to the KLM 4/16 and can also be configured via our Kraftwerk ControlPanel. Brightness, flashing speeds, and basic functionality (e.g., whether the high beam should be switched on the output) can be set separately for each output. Further information can be found under Highlights & Details. KLM 4/16 (4 servo inputs, 16 switching outputs, 5 bus outputs) Ready-to-install lighting boards Plug & Play solution (connect and drive) Compatible with all sound modules Compatible with all speed controllers Compatible with Tamiya MFU Expandable with various lighting boards Expandable with infrared for trailer lighting Customizable down to the smallest detail via PC to match the prototype No programming knowledge required PC software available for free download Technical Data Power supply: via receiver power supply (BEC of the speed controller) Max. Power consumption 20mA per device and 20mA per LED. Front LEDs (per side): yellow: 1x 3mm; white: 2x 3mm, 1x 5mm; yellow wired: 2x 3mm; white wired: 1x 3mm. Ultra-bright high-performance LEDs. Additional outputs at the front: 3 with 180 Ohm resistors each. Rear LEDs (per side): red: 1x 3mm, 1x 5mm; yellow: 1x 5mm; white: 1x 3mm. Ultra-bright high-performance LEDs. Additional outputs at the rear: 2 each with 180 Ohm resistors. Scope of delivery: Light Assistant KLM 4/16, four ready-to-install lighting boards (2x front, 2x rear).

Available immediately, delivery time: 1-4 days

Product number: 11004

199,00 € 229,90 € (13.44% saved)

Subscriptions

4 distribution board (Kingbus system) with 50cm cables

4-way distributor (Kingbus system) with 50cm cables. This distributor can be used to expand the Kingbus system with new light modules. It works like a multiple socket in the home. This 4-way distributor is very suitable for connecting two rear light modules and the infrared transmitter module at the rear of a tractor unit. This means that only one twin cable leads to the front to the central module. This distributor is available with different cable lengths: 15, 30 and 50 cm.

Available immediately, delivery time: 1-4 days

Product number: 10876

10,50 €

Subscriptions

KLB 12-20 expansion board. The expansion board

1x KLB 12-20 expansion board. The expansion board offers the possibility of expanding the light assistant by a further 8 outputs. Plug & Play solution. The module, which is only 15 x 28 mm in size, offers the possibility of expanding the light assistant by a further eight outputs - capable of handling up to 20 mA. It is simply connected to one of the EasyBus outputs of the light assistant and is thus automatically integrated into the system. The outputs of the expansion board offer exactly the same functionality as the outputs of the light assistant. - In addition to some effect lighting, all the usual lighting functions in the original are available: - combined front light (parking light, low beam, high beam, headlight flasher and fog light) - combined rear light (parking light, brake light, rear fog light) - American rear light (parking light, brake light, indicator) - daytime running light with automatic lowering when indicator is activated - cornering light - cornering light - reversing light - indicator, hazard warning light, American indicator - multi-flashing light - running light - rotating light - KnightRider In addition to the basic behavior of the individual outputs, the brightness, the switching on and off speed, as well as the switching on and off duration for flashing functions can also be set. Dimensions: 15x28x13mm Number of switching outputs: 8 Current load capacity per output: 20mA Voltage at the + output: BEC voltage (5-6V)LED series resistor integrated: yes (180 Ohm)Power supply: via bus (BEC of the speed controller)Max. own power consumption: 25mA

Available immediately, delivery time: 1-4 days

Product number: 10113

19,90 €

Subscriptions

Trailer module for the Pistenking Kingbus system. IRAM module

Trailer module to the Pistenking Kingbus system. IRAM module. This trailer module is a true all-rounder. It is connected to the tractor unit via infrared. For data transmission, an infrared transmitter module must be installed in the tractor. (Article 11704). In addition to the normal Kingbus light modules, two motors can also be connected to this trailer module. This allows, for example, the supports or ramps on the trailer are operated. Each motor can also be equipped with an end position switch. The necessary preparations have already been made. Only the limit switches have to be connected to the supplied cable. The module has an input for a potentiometer. This measures the articulation angle between the tractor and the semi-trailer. We offer a separate parts kit (11702) for this purpose. The steering axle control can be switched between "caster" and "reverse" (by pressing a button on the Kingpad). It is also possible to manually control the axles to the desired steering angle - also by pressing a button on the Kingpad! Furthermore, up to 16 LEDs (side marker lights) can be connected in series to the module. The luminosity can be continuously dimmed using the potentiometer on the module. The LEDs switch on with the parking lights. With an additional Kingpad, which is mounted on the trailer, the motors (supports/ramps) can be operated even without an infrared connection to the tractor unit. This is helpful if, for example, the tractor has already been stowed away after a day of driving, but the ramps on the trailer still need to be folded in. All of these special functions can be operated via the existing Kingpad. The "S key" can be used to switch to a second level. The buttons for the light functions are used for the special functions (supports, ramps, fifth wheel plate, steering axles). To explain the second level keys, a narrow sticker is included that describes their functions. This is glued to the Kingpad between the upper and lower row of keys. For more detailed explanation, a sticker in the original Kingpad size is also included. This can be stuck to a free space on the remote control. Please also note the connection plan. In addition to the infrared receiver unit, all cables and plugs are also included. Kingbus systems purchased from November 2015 already support the trailer functions! For "older" modules, we can install a software update on the Kingbus central module! Contact us... Inputs / Outputs: 2x Kingbus outputs for light modules, 2x motor drivers (speed controller on/off/on, with soft start) up to 5A load capacity, end position cut-off for motor drivers, 1x rotating beacon, input for fifth wheel potentiometer (measures articulation angle between tractor and semi-trailer), servo control for steered axles on the trailer, Kingpad input on the trailer (for controlling motor drivers without connection to the tractor), up to 16 side marker lights in series without series resistor (parking lights), dimmable side marker lights, infrared receiver. Technical data: Operating voltage: 6-12 volts, module dimensions: 42 x 34 mm (L x W), cable lengths on the module: 200 mm

Available immediately, delivery time: 1-4 days

Product number: 11703

119,00 €

Subscriptions

Taillight Boards (Pair) for the 7 chamber taillights v

Rear light boards (pair) for the 7-chamber rear lights from Veroma/Carson. Kingbus system. Rear light modules for the 7-chamber rear lights from Veroma/Carson with just two cables. The light modules are delivered fully assembled and tested. They only need to be installed in the model. No adjustments to the housing are necessary! The lights can be controlled via the Kingpad (not included). The central module & Kingpad are not required for remote control systems from the brands Brixl, ScaleArt Commander and Blauzahn. Instead, the Kingbus interface is connected to the assigned receiver slot. This controls the light functions via the standard Kingbus cable!The Kingpad is not required in this case, as the light functions can be operated via switches and buttons on the remote control.Expanding the lighting system with new light modules is simple - just plug them in!Features:- Parking light- Rear fog light- Brake light via driving channel or Kingpad- Reversing light via driving channel or Kingpad- Left / right indicator- Indicator reset via steering channel- Hazard warning lightsScope of delivery:- 2 light modules (cable length 150mm each)Matching rear light housing (not included): Article 1905.

Available immediately, delivery time: 1-4 days

Product number: 10939

78,99 €

Subscriptions

RC Multibus USB interface for configuring power units

RC Multibus USB interface to configure Kraftwerk modules without a light assistant. This article replaces article 11216! With this interface, Kraftwerk's RCMultiBus modules can be configured and tested with and without a receiver. The EasyBus modules can also be connected directly to this interface and configured without a BusMaster (such as KLM 4/16 or RS1). EasyBus systems installed in the model can be connected using the double-sided patch cable provided. The RCMultiBus currently includes EasyBus, IBUS, SBUS, SUMD V3, CPPM and UART.

Available immediately, delivery time: 1-4 days

Product number: 12046

44,90 €

Subscriptions

EasyBus daytime running light replacement cable, 10cm long, single-sided with

EasyBus daytime running light replacement cable 10cm long 1-sided with post coupling. 1 side open strand ends.

Available immediately, delivery time: 1-4 days

Product number: 12171

2,59 €

Subscriptions

4-way distributor (Kingbus system) with 30cm cables.

4 distribution board (Kingbus system) with 30cm cables.

Available immediately, delivery time: 1-4 days

Product number: 11263

10,00 €

Subscriptions

EasyBus lighting system KLM 4 / 16 TAMIYA Scania R470 and R620

EasyBus KLM 4/16 lighting system for Tamiya Scania R470 and R620. This lighting system for the Tamiya Scania R470 and R620 features the new KLM 4/16 motor, ready-to-install lighting circuit boards, and an integrated infrared transmitter. The front lighting circuit boards are simply inserted into the light chambers from the rear and are held securely in place by a press fit. For the rear taillights, the original mounting tabs must be removed and a hole drilled for cable routing. The circuit boards, including the supplied dividers, are then glued into the modified lamp housings. The aforementioned dividers recreate the original five-chamber partition and simultaneously provide mounts for the headlight lenses. The system is controlled by a KLM 4/16, which is compatible with standard forward/reverse speed controllers (with or without separate brake), cruise control speed controllers, and all sound modules. The lighting functions can be controlled either with our control pad or in numerous other ways; please refer to the online manual for details. This starter set includes a complete lighting system for the TAMIYA Scania R470 and R620 and consists of two front and two rear lighting boards, as well as a KLM 4/16 light assistant. The lighting boards are connected directly to the KLM 4/16 and can also be configured via our Kraftwerk Control Panel. Brightness, flashing speed, and basic functionality (e.g., whether the high beams should be switched on at a particular output) can be set separately for each output. Information on this can be found Highlights & Details KLM 4/16 (4 servo inputs, 16 switching outputs, 5 bus outputs) Ready-to-install lighting boards Plug & Play solution (connect and drive) Compatible with all sound modules Compatible with all speed controllers Compatible with Tamiya MFU Expandable with various lighting boards Expandable with infrared for trailer lighting Customizable to the smallest detail via PC No programming knowledge required PC software available for free download Technical data Power supply: via receiver power supply (BEC of the speed controller) Max. Power consumption 20mA per device and 20mA per LED. Front LEDs (per side): yellow: 1x 3mm; white: 2x 3mm, 2x 5mm. Ultra-bright high-performance LEDs. Additional outputs at the front: 3, each with a 180 Ohm resistor. Rear LEDs (per side): red: 4x SMD 1206; yellow: 1x SMD 1206; white: 1x SMD 1206. Ultra-bright high-performance LEDs. Additional outputs at the rear: 1, each with a 180 Ohm resistor. Scope of delivery: Light Assistant KLM 4/16, four ready-to-install lighting boards (2x front, 2x rear).

Available immediately, delivery time: 1-4 days

Product number: 11000

230,81 €

Subscriptions

Holland taillights EasyBus. Power plant zone

EasyBus Holland-style taillights. These taillights consist of three combinations of taillights, brake lights, and turn signals, plus a reversing light or rear fog light, and are equipped with twenty LEDs. The taillights measure 50mm in width (dimensions: 50x13mm) and therefore fit the fenders of Tamiya models. Caution: When used on a trailer/semi-trailer, the mounting holes in the bumper may need to be repositioned.

Available immediately, delivery time: 1-4 days

Product number: 10447

114,89 €

Subscriptions

Kingbus lighting module Universal HECK. Kingbus system.

Kingbus lighting module Universal REAR. Kingbus system. 2 universal modules (1x left, 1x right)

Available immediately, delivery time: 1-4 days

Product number: 11493

56,00 €

Subscriptions

Infrared transmitter module for Pistenking Kingbus system.

Infrared transmitter module for the Pistenking Kingbus system. The infrared transmitter module is easily connected to the central module or a distribution box using a standard Kingbus cable. It transmits data wirelessly from the truck to the trailer via infrared. A servo for unlocking the fifth wheel/trailer hitch can be connected to the second output. It can later be operated via the Kingpad. Kingbus systems purchased from November 2015 onwards already support the trailer functions! A software update can be installed on "older" modules! Please contact us! Outputs: Connected infrared transmitter diode; Connection for fifth wheel/trailer hitch unlocking. Technical data: Module dimensions: 34 x 12 mm (L x W); Cable lengths: 150 mm

Available immediately, delivery time: 1-4 days

Product number: 11704

38,00 €

Subscriptions

EasyBus lighting boards for Tamiya MAN 18.540 and

1x EasyBus lighting board for Tamiya MAN 18.540 and TGX 26.540 rear. Suitable for the EasyBus system. The plug & play solution. Scope of delivery:1x lighting board for Tamiya MANs, rear, left1x lighting board for Tamiya MANs, rear, rightPlug & PlayPerfect fit for the rear lights of the Tamiya MANs.With 3-pin plug connection. Integrated series resistors.Connection wires each approx. 60cm long.Power supply comes from the receiver output.The following functions can be controlled with the LIGHT ASSISTANT main module:-Parking light/tail light-Brake light-Reverse light-American tail light-Indicator left/right-Hazard warning light-American indicator-Rear fog light

Available immediately, delivery time: 1-4 days

Product number: 9505

59,80 €

Subscriptions

Kingbus lighting set for the VOLVO FH16 / Tamiya model

Kingbus lighting set for the VOLVO FH16 model from Tamiya. Kingbus system. Complete set of central module, light boards, various cables and distributors and accessories. The light modules are delivered fully assembled and tested. They only need to be installed in the model. Adjustments to the housing may be necessary!Light boards for the Volvo FH16 from Tamiya with only two cables.The light modules are delivered fully assembled and tested. They only need to be installed in the model. Little or no adjustments to the housing are necessary!The lights can be controlled via the Kingpad (not included).The central module & Kingpad are not required for remote control systems from the brands Brixl, ScaleArt Commander and Blauzahn.Instead, the Kingbus interface is connected to the assigned receiver slot. This controls the lighting functions via the standard Kingbus cable!The Kingpad is not required in this case, as the lighting functions can be operated via switches and buttons on the remote control.Expanding the lighting system with new lighting modules is simple - just plug them in!Features:L-shaped parking lightDipped beam (only with parking light)High beam (latching only with dipped beam)High beam flasherFog light and rear fog lightBrake light via driving channelReversing light via driving channel or KingpadWiper indicators left / right and front / rearIndicator reset via steering channelAutomatic hazard warning lights Cornering light when steering or blinkingXenon effect!Scope of delivery:1 Kingbus central module dimensions: 34x23,5x8mm2 patch cable for connecting the central module to the receiver1 Kingbus 4-way distributor 50cm1 Kingbus 4-way distributor 15 cm6 light modules (cable length 150mm each)1 universal module DACH2 headlight inserts with light guidesTechnical data:Operating voltage: 5V via BECCurrent consumption: approx. 20mA (at rest)

Available immediately, delivery time: 1-4 days

Product number: 11711

269,00 €

Subscriptions

TAMIYA MB Arocs 3363/3348 front left/right incl. side indicators

TAMIYA MB Arocs 3363/3348 front left/right including side indicator LEDs. Ready-to-install lighting boards. For Kraftwerk EasyBus system.

Available immediately, delivery time: 1-4 days

Product number: 11407

79,90 €

Subscriptions

Kingpad for the Kingbus system for mounting on the remote control transmitter

Kingpad for the Kingbus system for mounting on the remote control transmitter. A Kingbus lighting system is required on the vehicle side. (not included).This pad enables the control of the Kingbus lighting system in the model. The various lights can be switched on and off at the touch of a button. Installation is very simple.In the current version, the Kingpad has 2 levels between which you can switch back and forth using the S button.Level 1 controls all light functions, level 2 controls special functions such as ramps, supports, axle steering, fifth wheel plate (unlock) and special functions.Technical data:Operating voltage: 3,3 - 5V (depending on the transmitter)Connection cable: 3-pinButtons: 12Dimensions: 63 x 25 x 4mmFeatures:11 buttons for light control1 button for level switching11 buttons for special functionsWorks parallel to the steering channel (in the middle position!)No additional channel required22 control functions are possible

Available immediately, delivery time: 1-4 days

Product number: 12281

40,00 €

Subscriptions

Kingbus lighting module Universal DACH. Kingbus system.

Kingbus lighting module Universal DACH. Kingbus system. 1 universal module with instructions.

Available immediately, delivery time: 1-4 days

Product number: 11705

32,00 €

Subscriptions

EasyBus lighting boards for Tamiya MAN 18.540 and

1x EasyBus lighting board for Tamiya MAN 18.540 and TGX 26.540, front. Suitable for the EasyBus system. The plug & play solution. Lighting boards for TAMIYA-MANs!Scope of delivery:1x lighting board for Tamiya MANs, left1x lighting board for Tamiya MANs, rightPlug & PlayPerfect fit for the front of the Tamiya MANs.With 3-pin plug connection. Integrated series resistors.With 3 individually usable additional outputs.Connection wires each approx. 30cm long.Power supply comes from the receiver output.The following functions can be controlled with the LIGHT ASSISTANT main module:-Parking light-Low beam-High beam-Fog light-Flash light-Left/right indicator-Hazard warning light-Xenon effect-Daytime running light-Corner light/cornering light

Available immediately, delivery time: 1-4 days

Product number: 9504

69,79 €

Subscriptions

Kraftwerk-Zone infrared transmitting diode, 5mm round. For KIES

Kraftwerk-Zone infrared transmitter diode 5mm round. For GRAVEL.

Available immediately, delivery time: 1-4 days

Product number: 11348

9,90 €

Subscriptions

BUS distributor with 3,5mm jack. With this distributor

1x BUS distributor with 3,5mm jack. This distributor allows the EasyBus outputs to be connected to the trailer via a pluggable jack socket. Plug & Play solution.

Available immediately, delivery time: 1-4 days

Product number: 9256

24,89 €

Subscriptions

4-way distributor (Kingbus system) without cable.

Available immediately, delivery time: 1-4 days

Product number: 12449

6,50 €

Subscriptions

Central module of the Pistenking Kingbus system

Central module of the Pistenking Kingbus system. The Kingbus is a two-wire bus system that enables multiple lighting functions via just two wires. The power supply for the lighting modules is also provided via these two wires. The central module receives commands from the Kingpad (remote control), evaluates them and sends the desired lighting functions to the lighting modules. In order to reproduce functions such as brake and reversing lights as well as indicators and cornering lights as faithfully as possible, the steering and driving channels are connected to the central module. The steering and driving channels are looped from the receiver to the central module using servo patch cables. The speed controller and steering servo are then connected to the outputs of the central module.Features:Parking lightDipped beam (only with parking light)High beam (latching only with dipped beam)High beam flasher (always possible)Automatic short beam when indicating or steeringFog light and rear fog lightBrake light via driving channelReversing light via driving channel or KingpadIndicator reset via steering channelHazard warning lights, rotating beacon/li>automatic. Cornering light when steering or flashingWork lights (front/rear)Xenon effect with the light functions!Scope of delivery:1 Kingbus central module dimensions: 34x23,5x8mm3 patch cables for connecting the central module to the receiver1 Kingbus patch cable 50cm1 Kingbus 4-way distributor 15 cmDetailed instructionsTechnical data:Operating voltage: 5V via BECDimensions: 34 x 23,5 x 8mmCurrent consumption: approx. 20mA (at rest)Max. current consumption 750mAInputs:1x driving channel1x steering channel1x KingPad10x light functions (ground switching)Outputs:1x driving channel1x steering channel1x KindPad (optional)3x Kingbus (max. 750mA short-circuit proof)2x switching outputs (max. 1A each short-circuit proof)

Available immediately, delivery time: 1-4 days

Product number: 12446

108,99 €

Subscriptions

Kingbus connector with 15 cm wire. Suitable for the Kingbus system

Kingbus connector with 15 cm wire. 2-pin. Suitable for the Kingbus system.

Available immediately, delivery time: 1-4 days

Product number: 13314

1,99 €

Subscriptions

KSB2 servo controller. For EasyBus system. For connection

1x KSB2 servo control. For EasyBus system. For connecting up to 2 servos This module expands your EasyBus system with 2 freely adjustable servo outputs. The KSB2 module does not require an additional power supply. Technical data: Dimensions: 28x40x11mm Supply voltage: via the EasyBus Servo outputs: 2 Details: Plug & Play solution 2 additional servo outputs for the EasyBus Adjustable via control panel Proportional functions (e.g. for steering servo) Digital functions (e.g. fifth wheel coupling, ramps or flaps) Center positions, rotation speeds and directions of rotation adjustable No programming knowledge required PC software can be downloaded free of charge The following functions can be implemented with this module: - Proportional function - Proportional function switched - Two positions - Two positions center position - Actuator - Hydraulic simulation - Fifth wheel plate - Trailer supports - Trough - Windscreen wiper - Searchlight

Available immediately, delivery time: 1-4 days

Product number: 9250

34,90 €

Subscriptions

KMB1 - 10A Speed Controller for Easy-Bus System for Easy-Bus

1x KMB1 - 10A speed controller for Easy-Bus system for auxiliary drives. The KMB 1-10A has a motor output with a load of 10A. It is intended for auxiliary drives and, thanks to the two connections for limit switches, is also ideal for spindle drives. Dimensions 34x23x12mm

Available immediately, delivery time: 1-4 days

Product number: 9251

39,89 €

Subscriptions

EasyBus replacement LED with 60cm cable. LED 3mm yellow with 60cm

EasyBus replacement LED with 60cm cable. LED 3mm clear, glowing yellow with 60cm strands and open strand ends. Suitable for side marker lights and lighting boards.

Available immediately, delivery time: 1-4 days

Product number: 12461

4,30 €

Subscriptions

1x KSB4 servo control. For EasyBus- system. To connect

1x KSB4 servo control. For EasyBus system. For connecting up to 4 servos. This module expands your EasyBus system by 4 freely adjustable servo outputs. The KSB4 module must also be provided with a power supply. The VCC cable is either routed to a free receiver output or connected to an external battery.Technical data:Dimensions: 24x20x6mmSupply voltage: 4-5 cells NiMH (max. 8V)Servo outputs: 4Details:Plug & Play solutionFour additional servo outputs for the EasyBusAdjustable via control panelProportional functions (e.g. for steering servo)Digital functions (e.g. fifth wheel, ramp or flaps)Center positions, rotation speeds and rotation directions adjustableNo programming knowledge requiredPC - software can be downloaded free of chargeThe following functions can be implemented with this module:-Proportional function-Proportional function switched-Two positions-Two positions center position-Actuator-Hydraulic simulation-Fifth wheel plate-Trailer supports-Trough-Windscreen wiper-Searchlight

Available immediately, delivery time: 1-4 days

Product number: 9249

38,90 €

Subscriptions

Kingbus lighting module universal roof with indicator

Kingbus lighting module universal DACH with indicator. Kingbus system. 1 universal module with instructions.

Available immediately, delivery time: 1-4 days

Product number: 12447

32,00 €

Subscriptions

EasyBus replacement LED with 15cm cable. LED 3mm clear, white light

EasyBus replacement LED with 15cm cable. 3mm clear LED, white light with 15cm wires and open wire ends. Suitable for side marker lights and lighting boards.

Available immediately, delivery time: 1-4 days

Product number: 13167

3,90 €

Subscriptions

Infrared receiver diode for the Pistenking Kingbus system 3-pin

Infrared receiver diode for the Pistenking Kingbus system. Original spare part with 3-pin SH socket. 1 piece. Replacement diode for the IRAM module.

Available immediately, delivery time: 1-4 days

Product number: 13319

7,15 €

Subscriptions

Power plant board TAMIYA Scania R470 and R620 front

TAMIYA Scania R470 and R620 front-ready lighting boards. For power plant EasyBus system.

Available immediately, delivery time: 1-4 days

Product number: 11024

69,79 €

Subscriptions

TAMIYA MB Arocs 3363 rear left/right. including series resistors

TAMIYA MB Arocs 3363 rear left / right. incl. series resistors. Ready to install lighting boards. For power plant EasyBus system. NOT for Arocs 3348 rear dumpers!

Available immediately, delivery time: 1-4 days

Product number: 11408

59,80 €

Subscriptions

Filter products