EasyBus KIEB 6/2/2 trailer lighting system for Tamiya or Carson trailers with Euro taillights. Installation tips & tricks: Tip 1: The KIEB 6/2/2 can be powered in three ways: via the battery connection, via a servo connection and the BEC of a connected speed controller, or via a bus output and the BEC of a connected KMB. Tip 2: After switching on, the red LED of the KIEB 6/2/2 will blink twice. The LED should then go out, provided an IR connection is established. If the red LED blinks irregularly, the receiver gain should be adjusted using the potentiometer. Tip 3: The IR transmitter's transmission can be checked by pointing the transmitting LED at a mobile phone camera. If a purple flicker is visible in the camera app, the diode is transmitting. Highlights & Details: Plug & Play solution (connect and drive); One motor output for trailer supports or spindle drives; Two freely adjustable servo outputs (e.g., for steerable trailing axle); Receives ALL information... all light functions and switching states... but also all proportional functions... up to 1.5m away or up to an angle of 90°; Lighting boards can be connected directly via EasyBus. Technical Data: Length (excluding pin length) 60mm; Width 40mm; Height 12.5mm; Voltage 4-5 cells (max. 8V); BEC 5V (1A); Switching outputs; Servo outputs 2; Motor outputs 2; EasyBus outputs 3; Bridgeable distance up to 1.5m; Maximum angle approximately 90°; Scope of delivery: KIEB 6/2/2 Item 10446; 2x Euro taillight board, Item 103492x machined Euro housing, item 10686 receiver diode, included in the KIEB. If the electronics are powered by a battery, we recommend (depending on available space) these items: Item 7110 with 4,8V, Item 11121 with 4,8V, Item 7823 with 4,8V, Item 7745 with 4,8V, Item 7549 with 6V, Item 6457 with 6V

EasyBus Lighting System KLM 4/16 for Tamiya Mercedes-Benz Actros 3363. The lighting system for the Tamiya Actros 3363 features the new KLM 4/16, ready-to-install lighting circuit boards, and an integrated infrared transmitter. The lighting circuit boards are simply inserted into the light chambers from the rear and are held in place by a press fit. The system is controlled by a KLM 4/16, which is compatible with standard forward/reverse speed controllers (with or without separate brake), cruise control speed controllers, and all sound modules. The lighting functions can be controlled either with our control pad or in numerous other ways; please refer to the online manual for details. This starter set includes a complete lighting system for the Tamiya Mercedes-Benz Actros 3363 and consists of two front lighting circuit boards with pre-wired LEDs for the side indicators, underride guard, and marker lights, as well as a KLM 4/16 light assistant. The lighting circuit boards are connected directly to the KLM 4/16 connected and can also be configured via our Kraftwerk ControlPanel. Brightness, flashing speeds, and basic functionality (e.g., whether the high beam should be switched on the output) can be set separately for each output. Further information can be found under Highlights & Details. KLM 4/16 (4 servo inputs, 16 switching outputs, 5 bus outputs) Ready-to-install lighting boards Plug & Play solution (connect and drive) Compatible with all sound modules Compatible with all speed controllers Compatible with Tamiya MFU Expandable with various lighting boards Expandable with infrared for trailer lighting Customizable to the smallest detail via PC No programming knowledge required PC software available for free download Technical Data Power supply: via receiver power supply (BEC of the speed controller) Max. current consumption 20mA per device and 20mA per LED Front LEDs (per side):

EasyBus Lighting System KLM 4/16 for Tamiya MAN TGX 18.540 / 26.540 The lighting system for the TAMIYA MAN TGX 18.540 / 26.540 features the new KLM 4/16 controller, ready-to-install lighting boards, and an integrated infrared transmitter. The lighting boards are simply inserted into the light chambers from the rear and are held securely in place by a press fit. The system is controlled by a KLM 4/16 controller, which is compatible with standard forward/reverse speed controllers (with or without separate brake), cruise control controllers, and all sound modules. The lighting functions can be controlled either with our control pad or in numerous other ways; please refer to the online manual for details. This starter set includes a complete lighting system for the TAMIYA MAN TGX 18.540 / 26.540 and consists of two front lighting boards with pre-wired LEDs for the side indicators. Underride protection and marker lights, as well as a light assistant KLM 4/16. The lighting boards are connected directly to the KLM 4/16 and can also be configured via our Kraftwerk ControlPanel. Brightness, flashing speeds, but also the basic functionality (e.g., whether the high beam should be switched on the output) can be set separately for each output. You can find information on this under Highlights & Details KLM 4/16 (4 servo inputs, 16 switching outputs, 5 bus outputs) Ready-to-install lighting boards Plug & Play solution (connect and drive) Compatible with all sound modules Compatible with all speed controllers Compatible with Tamiya MFU Expandable with a wide variety of lighting boards Expandable with infrared for trailer lighting Customizable to the smallest detail via PC No programming knowledge required PC software available for free download Technical data Power supply: via receiver power supply (BEC of the speed controller) Max. Power consumption 20mA per device and 20mA per LED. Front LEDs (per side): yellow: 1x 3mm; white: 2x 3mm, 3x 5mm, 1x SMD; yellow wired: 1x 3mm; white wired: 1x 3mm. Ultra-bright high-performance LEDs. Additional outputs at the front: 3 with 180 Ohm resistors each. Rear LEDs (per side): red: 4x SMD 1206; yellow: 1x SMD 1206; white: 1x SMD 1206. Ultra-bright high-performance LEDs. Additional outputs at the rear: 1 each with 180 Ohm resistors. Scope of delivery: Light Assistant KLM 4/16, four ready-to-install lighting boards (2x front, 2x rear).

Set consisting of RS1 and circuit boards for front and rear. Speed ​​controller, lighting system, sound module in one incl. Complete lighting for Scania 770 S from Tamiya. Robust speed controllerThe speed controller can be permanently loaded with 25A and, thanks to the 32kHz control, is also suitable for bell-armature motors. It offers manual transmission support for up to four gears, a clutch function, handbrake, optional inertia simulation and a cruise control function, which does not work like the competition (stick deflection controls acceleration), but like the original: the throttle deflection controls the speed and the cruise control is activated by pressing a button. Pressing the button again or braking deactivates the cruise control.Extraordinary soundKraftwerK is once again setting standards in programmability. While the competition can only use a few sound snippets for the driving sound, KraftwerK can use as many as you like and it works as follows: First, the speed range is defined, e.g. 500 rpm immediately after starting and 2300 rpm when the engine is running out. Then sound snippets are stored for any number of areas and defined with base speed, minimum and maximum. At minimum the sound is faded in at a speed-adjusted level, at it is played at full volume and at a speed of 1:1, and up to maximum it is again adjusted to the speed and finally faded out. The snippets can and should of course overlap, which can create an ultra-realistic sound. In total there are three sound tracks: 2x acceleration and 1x deceleration. The first sound track is the normal driving sound, the second sound track can either be mixed proportionally as a load or switched. The third sound track is the delay sound and is automatically added when you release the joystick. If that's too complicated for you, you'll be pleased to know that 3 high-quality sounds are already included with the module. In the future there will also be a sound library with premium sounds that can be purchased for a few euros and downloaded via the ControlPanel and saved on your own module.Unlimited expandabilityKraftwerK's leading role in the field of RC bus systems is now fully evident in the RS1. The RS6 can be expanded as required via the 1 EasyBus outputs. Lighting boards, switching extensions, servo controls and much more can be controlled via the EasyBus. But the RS1 has one more special gimmick: on the upper side there are four individual sockets that are barely visible and can be used to plug in another module. The first module in this series is the BL8A, an 8A brushless controller designed for hydraulic pumps.Versatile connections / technical dataBattery (6 - 20V)Motor 25A, up to 32kHz, brush and bell-armature motor5 servo inputs or SUMD, IBUS, SBUS, CPPM5 servo outputs6 bus outputs8 switching outputs 500mA2 switching outputs 10AInfrared transmitter (diode included)SpeakerDimensions 63x44x28mmCharacteristics of the drive controllerOperating voltage 6-20VBEC 6V / 3ATimension frequency adjustable up to 32kHZClutch functionHandbrake functionManual transmission supportAdjustable inertia simulationAdjustable cruise controlProtection functions: battery undervoltage, motor short circuit, overtemperatureFunctions for servo outputsProportional functionProportional function directPropFunction switchedTwo positionsThree positionsFifth wheel plateTrailer supports MotorDump truck/tipper MotorRamp/Platform MotorManual transmissionSound featuresUnlimited number of sounds10-15 sounds that can be played simultaneouslyPlay modes: Touch, loop, once, permanent, random, stop pointsFormats: WAV, MP3 Usable sampling rate: All (automatic conversion to 44.100)Volume control: Potentiometer, via channel, via softwareSD card: max. 32 GB Features Lighting System Control: Light and sound control pad, user-defined channels, multi-switch Functions Hazard lights Left turn signal Right turn signal Sequential turn signal Parking lights Position lights Parking lights and low beam Parking lights and high beam Parking, low beam and high beam Parking lights and turn signals Position lights and turn signals Low beam Low beam and high beam High beam Fog lights Combined front lights Daytime running lights Taillight Brake lights Taillight, brake light Taillight, brake light and turn signal Taillight, rear fog light Rear fog light Combined rear lights Reversing lights Cornering lights / adaptive cornering lights Single switch Double switch Rotating beacon On/Off Strobe Sequential lights Knight Rider Aqua Effect Flash Proportional dimmer Recommended speaker: Item 9849.

EasyBus lighting system KLM 4/16 for Tamiya Mercedes-Benz Arocs 3348/4151. The lighting system for the TAMIYA Arocs 3348/4151 with the new KLM 4/16, ready-to-install lighting circuit boards, and integrated infrared transmitter. The lighting circuit boards are simply inserted into the light chambers from the rear and are held in place by a press fit. The system is controlled by a KLM 4/16, which is compatible with standard forward/reverse speed controllers (with or without separate brake), cruise control speed controllers, and all sound modules. The lighting functions can be controlled either with our control pad or in numerous other ways; please refer to the online manual for details. This starter set includes a complete lighting system for the Mercedes-Benz Arocs 3348/4151 from TAMIYA and consists of two front lighting circuit boards with wired LEDs for the side indicators, underride guard, and marker lights, as well as a KLM 4/16 light assistant. The lighting circuit boards are connected directly to the KLM 4/16 and can be controlled via this device. It can also be configured with our Kraftwerk ControlPanel. Brightness, flashing speeds, and basic functionality (e.g., whether the high beam should be switched on the output) can be set separately for each output. Information on this can be found under Highlights & Details KLM 4/16 (4 servo inputs, 16 switching outputs, 5 bus outputs) Ready-to-install lighting boards Plug & Play solution (connect and drive) Compatible with all sound modules Compatible with all speed controllers Compatible with Tamiya MFU Expandable with various lighting boards Expandable with infrared for trailer lighting Customizable down to the smallest detail via PC to match the prototype No programming knowledge required PC software available for free download Technical Data Power supply: via receiver power supply (BEC of the speed controller) Max. Power consumption 20mA per device and 20mA per LED. Front LEDs (per side): yellow: 1x 3mm; white: 2x 3mm, 1x 5mm; yellow wired: 2x 3mm; white wired: 1x 3mm. Ultra-bright high-performance LEDs. Additional outputs at the front: 3 with 180 Ohm resistors each. Rear LEDs (per side): red: 1x 3mm, 1x 5mm; yellow: 1x 5mm; white: 1x 3mm. Ultra-bright high-performance LEDs. Additional outputs at the rear: 2 each with 180 Ohm resistors. Scope of delivery: Light Assistant KLM 4/16, four ready-to-install lighting boards (2x front, 2x rear).

EasyBus KLM 4/16 lighting system for the Tamiya Mercedes-Benz Arocs 3363. This lighting system for the Tamiya Arocs 3363 features the new KLM 4/16 controller, ready-to-install lighting boards, and an integrated infrared transmitter. The lighting boards are simply inserted into the light chambers from the rear and are held securely in place by a press fit. The system is controlled by a KLM 4/16 controller, which is compatible with standard forward/reverse speed controllers (with or without separate brake), cruise control controllers, and all sound modules. The lighting functions can be controlled either with our control pad or in numerous other ways; please refer to the online manual for details. This starter set includes a complete lighting system for the Tamiya Mercedes-Benz Arocs 3363 and consists of two front lighting boards with pre-wired LEDs for the side indicators, underride guard, and marker lights, as well as a KLM 4/16 light assistant. They are connected directly to the KLM 4/16 and can also be configured via our Kraftwerk ControlPanel. Brightness, flashing speeds, and basic functionality (e.g., whether the high beam should be switched on the output) can be set separately for each output. Further information can be found under Highlights & Details. KLM 4/16 (4 servo inputs, 16 switching outputs, 5 bus outputs) Ready-to-install lighting boards Plug & Play solution (connect and drive) Compatible with all sound modules Compatible with all speed controllers Compatible with Tamiya MFU Expandable with various lighting boards Expandable with infrared for trailer lighting Customizable down to the smallest detail via PC to match the prototype No programming knowledge required PC software available for free download Technical Data Power supply: via receiver power supply (BEC of the speed controller) Max. Power consumption 20mA per device and 20mA per LED. Front LEDs (per side): yellow: 1x 3mm; white: 2x 3mm, 1x 5mm; yellow wired: 2x 3mm; white wired: 1x 3mm. Ultra-bright high-performance LEDs. Additional outputs at the front: 3 with 180 Ohm resistors each. Rear LEDs (per side): red: 1x 3mm, 1x 5mm; yellow: 1x 5mm; white: 1x 3mm. Ultra-bright high-performance LEDs. Additional outputs at the rear: 2 each with 180 Ohm resistors. Scope of delivery: Light Assistant KLM 4/16, four ready-to-install lighting boards (2x front, 2x rear).

EasyBus KLM 4/16 lighting system for Tamiya Scania R470 and R620. This lighting system for the Tamiya Scania R470 and R620 features the new KLM 4/16 motor, ready-to-install lighting circuit boards, and an integrated infrared transmitter. The front lighting circuit boards are simply inserted into the light chambers from the rear and are held securely in place by a press fit. For the rear taillights, the original mounting tabs must be removed and a hole drilled for cable routing. The circuit boards, including the supplied dividers, are then glued into the modified lamp housings. The aforementioned dividers recreate the original five-chamber partition and simultaneously provide mounts for the headlight lenses. The system is controlled by a KLM 4/16, which is compatible with standard forward/reverse speed controllers (with or without separate brake), cruise control speed controllers, and all sound modules. The lighting functions can be controlled either with our control pad or in numerous other ways; please refer to the online manual for details. This starter set includes a complete lighting system for the TAMIYA Scania R470 and R620 and consists of two front and two rear lighting boards, as well as a KLM 4/16 light assistant. The lighting boards are connected directly to the KLM 4/16 and can also be configured via our Kraftwerk Control Panel. Brightness, flashing speed, and basic functionality (e.g., whether the high beams should be switched on at a particular output) can be set separately for each output. Information on this can be found Highlights & Details KLM 4/16 (4 servo inputs, 16 switching outputs, 5 bus outputs) Ready-to-install lighting boards Plug & Play solution (connect and drive) Compatible with all sound modules Compatible with all speed controllers Compatible with Tamiya MFU Expandable with various lighting boards Expandable with infrared for trailer lighting Customizable to the smallest detail via PC No programming knowledge required PC software available for free download Technical data Power supply: via receiver power supply (BEC of the speed controller) Max. Power consumption 20mA per device and 20mA per LED. Front LEDs (per side): yellow: 1x 3mm; white: 2x 3mm, 2x 5mm. Ultra-bright high-performance LEDs. Additional outputs at the front: 3, each with a 180 Ohm resistor. Rear LEDs (per side): red: 4x SMD 1206; yellow: 1x SMD 1206; white: 1x SMD 1206. Ultra-bright high-performance LEDs. Additional outputs at the rear: 1, each with a 180 Ohm resistor. Scope of delivery: Light Assistant KLM 4/16, four ready-to-install lighting boards (2x front, 2x rear).

Kingbus lighting module Universal REAR. Kingbus system. 2 universal modules (1x left, 1x right)

Kingbus lighting set for the VOLVO FH16 model from Tamiya. Kingbus system. Complete set of central module, light boards, various cables and distributors and accessories. The light modules are delivered fully assembled and tested. They only need to be installed in the model. Adjustments to the housing may be necessary!Light boards for the Volvo FH16 from Tamiya with only two cables.The light modules are delivered fully assembled and tested. They only need to be installed in the model. Little or no adjustments to the housing are necessary!The lights can be controlled via the Kingpad (not included).The central module & Kingpad are not required for remote control systems from the brands Brixl, ScaleArt Commander and Blauzahn.Instead, the Kingbus interface is connected to the assigned receiver slot. This controls the lighting functions via the standard Kingbus cable!The Kingpad is not required in this case, as the lighting functions can be operated via switches and buttons on the remote control.Expanding the lighting system with new lighting modules is simple - just plug them in!Features:L-shaped parking lightDipped beam (only with parking light)High beam (latching only with dipped beam)High beam flasherFog light and rear fog lightBrake light via driving channelReversing light via driving channel or KingpadWiper indicators left / right and front / rearIndicator reset via steering channelAutomatic hazard warning lights Cornering light when steering or blinkingXenon effect!Scope of delivery:1 Kingbus central module dimensions: 34x23,5x8mm2 patch cable for connecting the central module to the receiver1 Kingbus 4-way distributor 50cm1 Kingbus 4-way distributor 15 cm6 light modules (cable length 150mm each)1 universal module DACH2 headlight inserts with light guidesTechnical data:Operating voltage: 5V via BECCurrent consumption: approx. 20mA (at rest)

TAMIYA MB Arocs 3363/3348 front left/right including side indicator LEDs. Ready-to-install lighting boards. For Kraftwerk EasyBus system.

Kingpad for the Kingbus system for mounting on the remote control transmitter. A Kingbus lighting system is required on the vehicle side. (not included).This pad enables the control of the Kingbus lighting system in the model. The various lights can be switched on and off at the touch of a button. Installation is very simple.In the current version, the Kingpad has 2 levels between which you can switch back and forth using the S button.Level 1 controls all light functions, level 2 controls special functions such as ramps, supports, axle steering, fifth wheel plate (unlock) and special functions.Technical data:Operating voltage: 3,3 - 5V (depending on the transmitter)Connection cable: 3-pinButtons: 12Dimensions: 63 x 25 x 4mmFeatures:11 buttons for light control1 button for level switching11 buttons for special functionsWorks parallel to the steering channel (in the middle position!)No additional channel required22 control functions are possible

Kingbus lighting module Universal DACH. Kingbus system. 1 universal module with instructions.

Central module of the Pistenking Kingbus system. The Kingbus is a two-wire bus system that enables multiple lighting functions via just two wires. The power supply for the lighting modules is also provided via these two wires. The central module receives commands from the Kingpad (remote control), evaluates them and sends the desired lighting functions to the lighting modules. In order to reproduce functions such as brake and reversing lights as well as indicators and cornering lights as faithfully as possible, the steering and driving channels are connected to the central module. The steering and driving channels are looped from the receiver to the central module using servo patch cables. The speed controller and steering servo are then connected to the outputs of the central module.Features:Parking lightDipped beam (only with parking light)High beam (latching only with dipped beam)High beam flasher (always possible)Automatic short beam when indicating or steeringFog light and rear fog lightBrake light via driving channelReversing light via driving channel or KingpadIndicator reset via steering channelHazard warning lights, rotating beacon/li>automatic. Cornering light when steering or flashingWork lights (front/rear)Xenon effect with the light functions!Scope of delivery:1 Kingbus central module dimensions: 34x23,5x8mm3 patch cables for connecting the central module to the receiver1 Kingbus patch cable 50cm1 Kingbus 4-way distributor 15 cmDetailed instructionsTechnical data:Operating voltage: 5V via BECDimensions: 34 x 23,5 x 8mmCurrent consumption: approx. 20mA (at rest)Max. current consumption 750mAInputs:1x driving channel1x steering channel1x KingPad10x light functions (ground switching)Outputs:1x driving channel1x steering channel1x KindPad (optional)3x Kingbus (max. 750mA short-circuit proof)2x switching outputs (max. 1A each short-circuit proof)

Kingbus lighting module universal DACH with indicator. Kingbus system. 1 universal module with instructions.

TAMIYA MB Arocs 3363 rear left / right. incl. series resistors. Ready to install lighting boards. For power plant EasyBus system. NOT for Arocs 3348 rear dumpers!

TAMIYA MB Arocs 3348 rear left/right including series resistors. Ready-to-install lighting boards. For Kraftwerk EasyBus system. These boards only fit the AROCS 3348 from Tamiya.

Kingbus lighting set UniversalCockpit Kingbus system. For installation in the cockpit. Individual LEDs are used (series resistor NOT necessary). Universal modules, e.g. for lighting a complete cockpit. Individual LEDs can be connected to this module. No additional series resistors are required for this, as these are already integrated in the module. The color of the LEDs to be connected is color-coded on the module. One LED can be connected to each output. Several LEDs (up to 100 mA total) can be connected to the outputs marked "HC". However, the series resistor must be calculated and installed between the universal module and the LED (only with HC output!). The light modules are delivered fully assembled and tested. They only need to be installed in the model. No adjustments to the housing are necessary!The modules are delivered fully assembled and tested.The lights can be controlled via the Kingpad (not included).Features of cockpit module outputs:Parking lightWorking light frontHigh beamIndicator left / rightHazard warning lightParking light (HC output)+5V connectionTechnical data:Dimensions: 27x15x8mmCable length: 300mmScope of delivery:1 universal module with instructions

EasyBus Lighting System KLM 4/16 for Tamiya Mercedes-Benz Actros 1851. This lighting system for the Tamiya MB Actros 1851 features the new KLM 4/16 controller, ready-to-install lighting circuit boards, and an integrated infrared transmitter. The lighting circuit boards are simply inserted into the light chambers from the rear and are held securely in place by a press fit. The system is controlled by a KLM 4/16 controller, which is compatible with standard forward/reverse speed controllers (with or without separate brake), cruise control controllers, and all sound modules. The lighting functions can be controlled either with our control pad or in numerous other ways; please refer to the online manual for details. This starter set includes a complete lighting system for the Tamiya Actros 1851 and consists of two front lighting circuit boards with pre-wired LEDs for the side indicators, underride guard, and marker lights, as well as a KLM 4/16 light assistant. The lighting circuit boards are connected directly to the KLM 4/16 controller. 4/16 connected and can also be configured via our Kraftwerk ControlPanel. Brightness, flashing speeds, and basic functionality (e.g., whether the high beam should be switched on the output) can be set separately for each output. Further information can be found under Highlights & Details KLM 4/16 (4 servo inputs, 16 switching outputs, 5 bus outputs) Ready-to-install lighting boards Plug & Play solution (connect and drive) Compatible with all sound modules Compatible with all speed controllers Compatible with Tamiya MFU Expandable with various lighting boards Expandable with infrared for trailer lighting Customizable down to the smallest detail via PC to match the prototype No programming knowledge required PC software available for free download Technical Data Power supply: via receiver power supply (BEC of the speed controller) Max. Power consumption 20mA per device and 20mA per LED. Front LEDs (per side): 1 x 3mm yellow, 1 x 3mm white, 2 x 5mm white, 2 x 3mm white (wired), 1 x 3mm yellow (wired). Ultra-bright high-performance LEDs. Additional outputs at the front: 3, each with a 180 Ohm resistor. Rear LEDs (per side): 1 x 5mm red, 1 x 5mm yellow, 1 x 3mm white, 1 x 3mm red. Ultra-bright high-performance LEDs. Additional outputs at the rear: 1, each with a 180 Ohm resistor. Scope of delivery: Light Assistant KLM 4/16, four ready-to-install lighting boards (2x front, 2x rear).

EasyBus lighting system KLM 4/16 for Tamiya Volvo FH16 timber transporter and tow truck. Incl. roof bar lighting. NEW generation. The lighting system for the TAMIYA Volvo FH16 timber transporter with the new KLM 4/16, ready-to-install lighting boards and integrated infrared transmitter. Also suitable for the Volvo TowTruck from Tamiya. The lighting boards are simply inserted into the light chambers from behind and are held in place by a press fit. The system is controlled by a KLM 4/16, which is compatible with normal forward-reverse speed controllers (with or without a separate brake), cruise control controllers and all sound modules. The lighting functions can be controlled either with our control pad or in numerous other ways, for details please refer to the online manual. This starter set includes a complete lighting system for the Volvo FH16 from TAMIYA and consists of two front and rear lighting boards each with wired LEDs for the side indicators, underrun protection and marker lights, as well as a KLM 4/16 light assistant. The lighting boards are connected directly to the KLM 4/16 and can also be configured using our Kraftwerk ControlPanel. Brightness, flashing speeds and also basic functionality (e.g. should the high beam be switched on at the output) can be set separately for each output. Information on this can be found under article 10822.Highlights & detailsKLM 4/16 (4 servo inputs, 16 switching outputs, 5 bus outputs) Ready-to-install lighting boardsPlug & play solution (connect and drive)Compatible with all sound modulesCompatible with all speed controllersCompatible with Tamiya MFUCan be expanded with a wide variety of lighting boardsCan be expanded with infrared for trailer lightingCan be adapted to the model down to the smallest detail using a PCNo programming knowledge requiredPC software can be downloaded free of chargeTechnical specificationsPower supply:via receiver power supply (BEC of the speed controller)Max. Power consumption 20mA per device and 20 mA per LEDLEDs front (per side):yellow: 1x 3mmwhite: 2x 3mm, 1x 5mmyellow wired: 2x 3mmwhite wired: 1x 3mmUltra-bright high-performance LEDsLEDs rear (per side):red: 1x 3mm, 1x 5mmyellow: 1x 5mmwhite: 1x 3mmUltra-bright high-performance LEDsAdditional outputs at the rear, 2 each with 180 Ohm resistanceScope of deliveryLight assistant KLM 4/16four ready-to-install lighting boards (2x front, 2x rear)Infrared transmitter diodeWired LEDs for side indicatorsWired LEDs for underrun protectionWired LEDs for marker lightsKLB-8 for the roof bar lighting.

Kingbus lighting set for the ACTROS model from Tamiya. Kingbus system. Complete set of central module, light boards, various cables and distributors and accessories. The light modules are delivered fully assembled and tested. They only need to be installed in the model. No adjustments to the housing are necessary!Light boards for the Mercedes-Benz Actros GigaSpace from Tamiya with only two cables.Suitable for Actros 1851 and 3363.The light modules are delivered fully assembled and tested. They only need to be installed in the model. No adjustments to the housing are necessary!The lights can be controlled via the Kingpad (not included).The central module & Kingpad are not required for remote control systems from the brands Brixl, ScaleArt Commander and Blauzahn.Instead, the Kingbus interface is connected to the assigned receiver slot. This controls the lighting functions via the standard Kingbus cable! The Kingpad is not required in this case, as the lighting functions can be operated via switches and buttons on the remote control. Expanding the lighting system with new lighting modules is simple - just plug them in! Features: - Parking light - Low beam (only with parking light) - High beam (latching only with low beam) - Headlight flasher - Fog light - Left / right indicator - Indicator reset via steering channel - Hazard warning lights - Automatic. Cornering light when steering or blinking - Xenon effect!Scope of delivery:- 1 Kingbus central module dimensions: 34x23,5x8mm- 2 patch cables for connecting the central module to the receiver- 1 Kingbus patch cable 50cm- 1 Kingbus 4-way distributor- 4 light modules (cable length 150mm each)- 4 LEDs for indicators and position lights (pluggable)- Fiber optic cable for daytime running lights- 2 fiber optic cable housingsTechnical data:Operating voltage: 5V via BECCurrent consumption: approx. 20mA (at rest)

Kingbus lighting module Universal FRONT Kingbus system. With xenon effect. 2 universal modules (1x left, 1x right). Universal modules for mounting on the front bumper of the model. Individual LEDs can be connected to the module. No additional series resistors are required as these are already integrated in the module!The color of the LED to be connected is marked on the module with a colored dot. One LED can be connected per output.Several LEDs (up to 100mA total) can be connected to the outputs marked "HC". However, the series resistor must be calculated and installed between the universal module and the LED (only with HC output)!The modules are delivered ready for installation and tested. The connection to the Kingbus lighting system is simple - just plug it in!Please also note the connection plan in the picture series.Design:The modules are available in two versions. These differ in the xenon effect (flashing) when the individual light functions are switched on. Depending on the model type, you can choose whether your model has xenon or halogen headlights (without flashing). Outputs:Parking lightDipped beam (only with parking light)High beam (latching only with dipped beam)Fog lightIndicator left / rightHazard warning lightsAutomatic cornering light when steering or blinking+5 voltsTechnical data:Module dimensions: 27 x 15 x 8mm (LxWxH)Cable length: 150mmScope of delivery:2 universal modules (left and right)

Kingbus lighting set universal.XENON. Complete universal set. Kingbus system. Complete set of central module, light boards, various cables and distributors and accessories. Universal modules for lighting a complete model. Individual LEDs can be connected to each module. No additional series resistors are required for this, as these are already integrated in the module. The color of the LEDs to be connected is marked on the module with a colored dot. One LED can be connected to each output. Several LEDs (up to 100 mA total) can be connected to the outputs marked "HC". However, the series resistor must be calculated and installed between the universal module and the LED (only with HC output!). The light modules are delivered fully assembled and tested. They only need to be installed in the model. No adjustments to the housing are necessary!These modules are available in 2 versions: WITH Xenox effect (flashes when switched on) or as halogen headlights (without flashing).The modules are delivered fully assembled and tested.The lights can be controlled via the Kingpad (not included).Features of front module outputs:Parking lightDipped beam (only with parking light)High beam (latching only with dipped beam)High beam flasherFog lightIndicator left / rightHazard warning lightsautomatic. Cornering light when steering or blinkingXenon effect!+5V connectionRear module outputs:Parking lightRear fog lightBrake light via driving channelReversing light via driving channel or KingpadLeft/right indicatorHazard warning light+5V connectionTechnical data:Dimensions per module: 27x15x8mmCable length per module: 150mmScope of delivery:1 Kingbus central module dimensions: 34x23,5x8mm3 patch cables for connecting the central module to the receiver1 Kingbus patch cable 50cm1 Kingbus 4-way distributor2 universal modules for the front (left/right)2 universal modules for the rear (left/right)

1x EasyBus lighting system TAMIYA MB Actros 1851 Gigaspace + side indicator LEDs. KLM 4/12-500 variant. The plug & play solution. Ready-to-install lighting boards, compatible with all sound modules, cruise control and the Tamiya MFU-xx. The EasyBus lighting systems can be expanded with different lighting boards, IR trailer lighting, etc. The PC software can be downloaded free of charge. No programming knowledge is required. The control system can be customized down to the smallest detail. Scope of delivery: -2x front board for Actros WITH side indicator (1x right/1x left), item 9509 -2x rear board for Actros, (1x left, 1 right) item 9508 -1x KLM 4/12-500 light assistant Of course, we are happy to configure the lighting system according to your ideas and save them in addition.

Kingbus Universal Front Lighting Module for the Kingbus System. With halogen effect, 2 universal modules (1x left, 1x right). Universal modules for mounting on the model's front bumper. Individual LEDs can be connected to the module. No additional resistors are required, as these are already integrated into the module! The color of the LED to be connected is indicated on the module with a colored dot. One LED can be connected to each output. Multiple LEDs (up to 100mA total) can be connected to the outputs marked "HC". However, the resistor must be calculated and installed between the universal module and the LED (only for HC outputs)! The modules are delivered ready for installation and tested. Connection to the Kingbus lighting system is simple - just plug it in! Please also refer to the connection diagram in the image gallery. Version: The modules are available in two versions. These differ in the xenon effect (flashing) when the individual lighting functions are switched on. Depending on the model type, you can select whether your vehicle has xenon or halogen headlights (without flashing). Outputs: Parking lights, Low beam (only with parking lights), High beam (latching, only with low beam), Headlight flasher, Fog lights, Left/right turn signals, Hazard warning lights, Automatic cornering lights when steering or indicating, +5 volts. Technical data: Module dimensions: 27 x 15 x 8 mm (L x W x H), Cable length: 150 mm. Scope of delivery: 2 universal modules (left and right).

Kingbus lighting set for the AROCS model from Tamiya. Kingbus system. Complete set of central module, light boards, various cables and distributors and accessories. The light modules are delivered fully assembled and tested. They only need to be installed in the model. No adjustments to the housing are necessary!Light boards for the Mercedes-Benz Arocs 3363 from Tamiya with just two cables.The light modules are delivered fully assembled and tested. They only need to be installed in the model. No adjustments to the housing are necessary!The lights can be controlled via the Kingpad (not included).The central module & Kingpad are not required for remote control systems from the brands Brixl, ScaleArt Commander and Blauzahn.Instead, the Kingbus interface is connected to the assigned receiver slot. This controls the lighting functions via the standard Kingbus cable!The Kingpad is not required in this case, as the lighting functions can be operated via switches and buttons on the remote control.Expanding the lighting system with new lighting modules is simple - just plug them in!Features:Parking lightDipped beam (only with parking light)High beam (latching only with dipped beam)High beam flasherFog lightBrake light via driving channelReversing light via driving channel or KingpadIndicator left / rightIndicator reset via steering channelHazard warning lightsautomatic. Cornering light when steering or blinkingXenon effect!Scope of delivery:1 Kingbus central module dimensions: 34x23,5x8mm2 patch cable for connecting the central module to the receiver1 Kingbus patch cable 50cm1 Kingbus 4-way distributor4 light modules (cable length 150mm each)4 LEDs for indicators and position lights (pluggable)2 housings for daytime running lightsTechnical data:Operating voltage: 5V via BECCurrent consumption: approx. 20mA (at rest)

Kingpad-IRAM for the Kingbus system, for mounting on the semi-trailer/trailer. This module is NOT attached to the remote control! This Kingpad with 4 buttons (2 functions) is attached to the semi-trailer/trailer, not to the remote control! This allows the ramps and supports (or individual special functions) to be operated even without the remote control. The semi-trailer/trailer only needs to be connected to the battery; it does not require a radio connection to the tractor unit! This can be very useful, for example, during the construction phase. This Kingpad is also very helpful at an event, for example, if the tractor unit is already stowed in the car during loading in the evening and the ramps on the semi-trailer still need to be retracted because it was forgotten earlier. Technical data: Dimensions: 43 x 13 x 4 mm, Cable length: 100 mm, Connection: Cable with plug, Voltage: Supplied by connecting to the IRAM module, Buttons: 4 (2 functions)

1x EasyBus lighting system for TAMIYA GrandHauler. Variant KLM 4/0 The plug & play solution. Ready-to-install lighting boards, compatible with all sound modules, speed controllers and the Tamiya MFU. The EasyBus lighting systems can be expanded with different lighting boards, IR trailer lighting, etc. The PC software can be downloaded free of charge. No programming knowledge is required. The control system can be customized down to the smallest detail. Scope of delivery: - 2x front board for GrandHauler (1x left, 1x right) - 1x rear board for GrandHauler - 1x KLM 4/0 light assistant, article 9243 - 2x extension boards KLB 8-20 Of course, we are also happy to configure your lighting system according to your ideas and save them in addition.

1x EasyBus lighting system for TAMIYA Freightliner CASCADIA. Variant KLM 4/0 The plug & play solution. Ready-to-install lighting boards, compatible with all sound modules, speed controllers and the Tamiya MFU. The EasyBus lighting systems can be expanded with different lighting boards, IR trailer lighting, etc. The PC software can be downloaded free of charge. No programming knowledge is required. The control system can be customized down to the smallest detail. Scope of delivery: - 2x front board for CASCADIA (1x left, 1x right) - 1x rear board for CASCADIA - 1x KLM 4/0 light assistant, article 9244 - 3x extension boards KLB 8-20 Of course, we are also happy to configure your lighting system according to your ideas and save them in addition.

1x EasyBus lighting system TAMIYA MB Actros 1851 Gigaspace + side indicator LEDs. KLM 4/0 variant. The plug & play solution. Ready-to-install lighting boards, compatible with all sound modules, speed controllers and the Tamiya MFU. The EasyBus lighting systems can be expanded with different lighting boards, IR trailer lighting, etc.The PC software can be downloaded free of charge. No programming knowledge is required. The control system can be customized down to the smallest detail.Scope of delivery:-2x front board for Actros-2x rear board for Actros-2x side indicator LEDs-1x KLM 4/0 light assistant

Kingbus lighting set for the MAN model from Tamiya. Kingbus system. Complete set of central module, light boards, various cables and distributors and accessories. The light modules are delivered fully assembled and tested. They only need to be installed in the model. No adjustments to the housing are necessary!Light boards for the MANs from Tamiya with only two cables.The light modules are delivered fully assembled and tested. They only need to be installed in the model. No adjustments to the housing are necessary!The lights can be controlled via the Kingpad (not included).The central module & Kingpad are not required for remote control systems from the brands Brixl, ScaleArt Commander and Blauzahn.Instead, the Kingbus interface is connected to the assigned receiver slot. This controls the lighting functions via the standard Kingbus cable! The Kingpad is not required in this case, as the lighting functions can be operated using switches and buttons on the remote control. Expanding the lighting system with new lighting modules is simple - just plug them in! Features: - Parking light - Low beam (only with parking light) - High beam (latching only with low beam) - Headlight flasher - Fog light and rear fog light - Brake light via driving channel - Reversing light via driving channel or Kingpad - Left / right indicator - Indicator reset via steering channel - Hazard warning lights - Automatic. Cornering light when steering or blinking - Xenon effect!Scope of delivery:- 1 Kingbus central module dimensions: 34x23,5x8mm- 2 patch cables for connecting the central module to the receiver- 1 Kingbus patch cable 50cm- 1 Kingbus 4-way distributor- 4 light modules (cable length 150mm each)- 4 LEDs for indicators and position lights (hard-wired)Technical data:Operating voltage: 5V via BECCurrent consumption: approx. 20mA (at rest)

Kingbus lighting set for the SCANIA model from Tamiya. Kingbus system. Complete set of central module, light boards, various cables and distributors and accessories. For the R470 and R620 models. The light modules are delivered fully assembled and tested. They only need to be installed in the model. No adjustments to the housing are necessary!Light boards for the SCANIAs R470 and R620 from Tamiya with just two cables.The light modules are delivered fully assembled and tested. They only need to be installed in the model. No adjustments to the housing are necessary!The lights can be controlled via the Kingpad (not included).The central module & Kingpad are not required for remote control systems from the brands Brixl, ScaleArt Commander and Blauzahn.Instead, the Kingbus interface is connected to the assigned receiver slot. This controls the lighting functions via the standard Kingbus cable! The Kingpad is not required in this case, as the lighting functions can be operated via switches and buttons on the remote control. Expanding the lighting system with new lighting modules is simple - just plug them in! Features: - Parking light - Low beam (only with parking light) - High beam (latching only with low beam) - Headlight flasher - Fog light - Left / right indicator - Indicator reset via steering channel - Hazard warning lights - Automatic. Cornering light when steering or blinking - Xenon effect!Scope of delivery:- 1 Kingbus central module dimensions: 34x23,5x8mm- 2 patch cables for connecting the central module to the receiver- 1 Kingbus patch cable 50cm- 1 Kingbus 4-way distributor- 4 light modules (cable length 150mm each)- Inserts for rear lights in whiteTechnical data:Operating voltage: 5V via BECCurrent consumption: approx. 20mA (at rest)