building blocks

KraftwerK control pad Light & Sound. Control pad for all

KraftweK Light & Sound Control Pad. Control pad for all transmitters for a power plant lighting system. The pad is connected to a free proportional channel in the transmitter and behaves like a normal joystick, meaning it doesn't use complex transmission signals like most multiswitches, making it suitable for use with any remote control transmitter. The Light & Sound control pad controls all lighting functions, the trailer supports, the tipping body, the fifth wheel coupling, and 11 additional functions (e.g., a rotating beacon), the gearshift, and two servos. There is also a button for "all on" and "all off" if you need to act quickly! Dimensions: 2 x 78 mm. The pad is compatible with all remote control transmitters. It is important that the selected channel is a proportional channel, meaning a servo connected to the corresponding receiver output must be continuously controllable. (Switched channels are unsuitable!!!) Ideally, the channel should be unoccupied, meaning no other control element (joystick, linear regulator, etc.) should be connected. Since new transmitters often no longer have expansion channels, an occupied channel can be used in an emergency. However, this channel must not be in use and must always be in the center position (otherwise, the functions will not switch).

Available immediately, delivery time: 1-4 days

Product number: 11089

€ 74,90 *

Subscriptions

1x KLB 8-500 expansion board. The expansion board

1x KLB 8-500 expansion board. The expansion board offers the possibility of expanding the light assistant by a further 8 outputs. Plug & Play solution. The module, which is only 21 x 26 mm in size, offers the possibility of expanding the light assistant by a further eight outputs - with a load capacity of up to 500 mA. It is simply connected to one of the EasyBus outputs of the light assistant and is thus automatically integrated into the system. The outputs of the expansion board offer exactly the same functionality as the outputs of the light assistant. - In addition to some effect lighting, all the usual lighting functions in the original are available: - combined front light (parking light, low beam, high beam, headlight flasher and fog light) - combined rear light (parking light, brake light, rear fog light) - American rear light (parking light, brake light, indicator) - daytime running light with automatic lowering when indicator is activated - cornering light - cornering light - reversing light - indicator, hazard warning light, American indicator - multi-flashing light - running light - rotating light - KnightRider In addition to the basic behavior of the individual outputs, the brightness, the switching on and off speed, as well as the switching on and off duration for flashing functions can also be set. Dimensions: 23x28x13mm Number of switching outputs: 8 Current load capacity per output: 500mA Voltage at the + output: BEC voltage (5-6V)LED resistor integrated: noPower supply: via bus (BEC of the speed controller)Max. own power consumption: 25mA

Available immediately, delivery time: 1-4 days

Product number: 9245

€ 34,90 *

Subscriptions

1x KLB 8-20 expansion board. The expansion board bie

1x KLB 8-20 expansion board. The expansion board offers the possibility of expanding the light assistant by a further 8 outputs. Plug & Play solution. The module, which is only 15 x 28 mm in size, offers the possibility of expanding the light assistant by a further eight outputs - capable of handling up to 20 mA. It is simply connected to one of the EasyBus outputs of the light assistant and is thus automatically integrated into the system. The outputs of the expansion board offer exactly the same functionality as the outputs of the light assistant. - In addition to some effect lighting, all the usual lighting functions in the original are available: - combined front light (parking light, low beam, high beam, headlight flasher and fog light) - combined rear light (parking light, brake light, rear fog light) - American rear light (parking light, brake light, indicator) - daytime running light with automatic lowering when indicator is activated - cornering light - cornering light - reversing light - indicator, hazard warning light, American indicator - multi-flashing light - running light - rotating light - KnightRider In addition to the basic behavior of the individual outputs, the brightness, the switching on and off speed, as well as the switching on and off duration for flashing functions can also be set. Dimensions: 15x28x13mm Number of switching outputs: 8 Current load capacity per output: 20mA Voltage at the + output: BEC voltage (5-6V)LED series resistor integrated: yes (180 Ohm)Power supply: via bus (BEC of the speed controller)Max. own power consumption: 25mA

Ready to ship in 30 days, delivery time 1-4 days

Product number: 10114

€ 29,90 *

Subscriptions

1x BUS - distribution. 1 6 on. Let this distribution

1x BUS distributor. 1 to 6. With this distributor, the EasyBus outputs of the light assistants can be divided into a further 6 outputs. Plug & Play solution. With this distributor, the EasyBus outputs of the light assistants can be divided into a further 6 outputs. Connection cable with a length of approx. 15 cm.

Available immediately, delivery time: 1-4 days

Product number: 9255

€ 4,90 *

Subscriptions

EasyBus replacement cable 30cm long, 1-sided with post coupling

EasyBus replacement cable 30cm long. 1-sided with post coupling. 1 side open wire ends.

Available immediately, delivery time: 1-4 days

Product number: 12168

€ 2,80 *

Subscriptions

Power station zone Infrared transmitter diode

Kraftwerk-Zone infrared transmitting diode, 5mm round. For KLM 4/16.

Available immediately, delivery time: 1-4 days

Product number: 10448

€ 8,25 *

Subscriptions

1x KLM 4 / 16 light assistant. The light assistant is the

1x KLM 4/16 light assistant. The light assistant is the core component of a lighting system that can be expanded as required. Incl. Transmitting diode. Plug & Play solution. Core component of the lighting system, compatible with all sound modules, speed controllers and the Tamiya MFU-xx. The EasyBus lighting systems are equipped with different lighting boards, IR trailer lighting, etc. expandable.The PC software can be downloaded free of charge. No programming knowledge is required. The control can be customized down to the smallest detail. Technical data: - Dimensions 51x36x13 mm - 4 inputs (steering, throttle, channel 1, channel 2) - 2 servo outputs (steering servo, speed controller) - 5 bus outputs (for expansion modules) - 16 switching outputs with max. 500mA, freely configurable-1x USB socket (Micro-USB, for configuration)From April 2018 incl. Transmitter diodeWe are of course happy to configure the lighting system according to your ideas and also save them.The KLM 4/16 light assistant is the further development of the KLM 4/12-500. Compact design, easy operation and compatibility with the most common systems on the market are its main strengths. It is compatible with standard forward-reverse speed controllers (with or without a separate brake), with the cruise control controllers from Servonaut and all sound modules. The light functions can be controlled in a variety of ways; please refer to the manual for details. The module, which is only 52 x 36 x 13 mm in size, offers eight high-current outputs (500 mA each and eight switching outputs with integrated series resistors), four adjustable servo outputs, an infrared output, a USB socket that is only required for configuration and five bus outputs, via which the system can be expanded as required with additional switching, servo or motor functions. Standard assignment of the outputs:-Output 1 & 2: parking light & high beam & headlight flasher-Output 3 & 4: dipped beam-Output 5: left indicator-Output 6: right indicator-Output 7 & 8: tail light & brake light-Output 9: rear fog light-Output 10: reversing light-Output 11 & 12: speed camera-It is possible to select the behavior of each individual output completely independently and freely via PC and to configure it on a percentage basis. In addition to some effect lighting, you can choose from all the usual lighting functions in the original: -- combined front light (parking light, low beam, high beam, headlight flasher and fog light) -- combined rear light (parking light, brake light, -- American rear light (parking light, brake light, indicator) -- daytime running light with automatic lowering when the indicator is activated -- cornering light -- curve light -- reversing light -- indicator, hazard warning light, American indicator -- multi-flashing light -- running light -- rotating light -- KnightRider In addition to the basic behavior of the individual outputs, the brightness, the switching on and off speed, and the switching on and off duration for the flashing functions can also be set. How easy this is can be tested in advance using the demo mode of the free PC software ControlPanel. The module is connected to four channels of the receiver. In addition to gas and steering, two channels (K1 and K2) are used to control the lighting. Please refer to the manual for the different variants! During development, special attention was paid to ease of use. You do not need any electronic experience to use this system! You will find all the information you need in the included quick start guide! Scope of delivery: 1x KLM 4/16 light assistant, 1x IR transmitting diode, 4x servo patch cables 10cm

Available immediately, delivery time: 1-4 days

Product number: 10822

€ 114,89 *

Subscriptions

Power plant set with RS1 for Scania 770 S from Tamiya

Set consisting of RS1 and circuit boards for front and rear. Speed controller, lighting system, sound module in one incl. Complete lighting for Scania 770 S from Tamiya. Robust speed controllerThe speed controller can be permanently loaded with 25A and, thanks to the 32kHz control, is also suitable for bell-armature motors. It offers manual transmission support for up to four gears, a clutch function, handbrake, optional inertia simulation and a cruise control function, which does not work like the competition (stick deflection controls acceleration), but like the original: the throttle deflection controls the speed and the cruise control is activated by pressing a button. Pressing the button again or braking deactivates the cruise control.Extraordinary soundKraftwerK is once again setting standards in programmability. While the competition can only use a few sound snippets for the driving sound, KraftwerK can use as many as you like and it works as follows: First, the speed range is defined, e.g. 500 rpm immediately after starting and 2300 rpm when the engine is running out. Then sound snippets are stored for any number of areas and defined with base speed, minimum and maximum. At minimum the sound is faded in at a speed-adjusted level, at it is played at full volume and at a speed of 1:1, and up to maximum it is again adjusted to the speed and finally faded out. The snippets can and should of course overlap, which can create an ultra-realistic sound. In total there are three sound tracks: 2x acceleration and 1x deceleration. The first sound track is the normal driving sound, the second sound track can either be mixed proportionally as a load or switched. The third sound track is the delay sound and is automatically added when you release the joystick. If that's too complicated for you, you'll be pleased to know that 3 high-quality sounds are already included with the module. In the future there will also be a sound library with premium sounds that can be purchased for a few euros and downloaded via the ControlPanel and saved on your own module.Unlimited expandabilityKraftwerK's leading role in the field of RC bus systems is now fully evident in the RS1. The RS6 can be expanded as required via the 1 EasyBus outputs. Lighting boards, switching extensions, servo controls and much more can be controlled via the EasyBus. But the RS1 has one more special gimmick: on the upper side there are four individual sockets that are barely visible and can be used to plug in another module. The first module in this series is the BL8A, an 8A brushless controller designed for hydraulic pumps.Versatile connections / technical dataBattery (6 - 20V)Motor 25A, up to 32kHz, brush and bell-armature motor5 servo inputs or SUMD, IBUS, SBUS, CPPM5 servo outputs6 bus outputs8 switching outputs 500mA2 switching outputs 10AInfrared transmitter (diode included)SpeakerDimensions 63x44x28mmCharacteristics of the drive controllerOperating voltage 6-20VBEC 6V / 3ATimension frequency adjustable up to 32kHZClutch functionHandbrake functionManual transmission supportAdjustable inertia simulationAdjustable cruise controlProtection functions: battery undervoltage, motor short circuit, overtemperatureFunctions for servo outputsProportional functionProportional function directPropFunction switchedTwo positionsThree positionsFifth wheel plateTrailer supports MotorDump truck/tipper MotorRamp/Platform MotorManual transmissionSound featuresUnlimited number of sounds10-15 sounds that can be played simultaneouslyPlay modes: Touch, loop, once, permanent, random, stop pointsFormats: WAV, MP3 Usable sampling rate: All (automatic conversion to 44.100)Volume control: Potentiometer, via channel, via softwareSD card: max. 32 GB Features Lighting System Control: Light and sound control pad, user-defined channels, multi-switch Functions Hazard lights Left turn signal Right turn signal Sequential turn signal Parking lights Position lights Parking lights and low beam Parking lights and high beam Parking, low beam and high beam Parking lights and turn signals Position lights and turn signals Low beam Low beam and high beam High beam Fog lights Combined front lights Daytime running lights Taillight Brake lights Taillight, brake light Taillight, brake light and turn signal Taillight, rear fog light Rear fog light Combined rear lights Reversing lights Cornering lights / adaptive cornering lights Single switch Double switch Rotating beacon On/Off Strobe Sequential lights Knight Rider Aqua Effect Flash Proportional dimmer Recommended speaker: Item 9849.

Available immediately, delivery time: 1-4 days

Product number: 11382

€ 9,90 *

Subscriptions

KIEB 6 / 2 / 2 Infrared Receiver. Power plant plug & play solution

KIEB 6/2/2 Infrared Receiver. Plug & Play solution. Compatible with the EasyBus system. Power plant zone. The KIEB 6/2/2 receives all EasyBus information from the infrared transmitter. Plus: includes a 5 mm receiving diode, six switching outputs, two servo outputs, two motor outputs, and three EasyBus outputs. Technical data: Length (excluding pin length): 60 mm; Width: 40 mm; Height: 12.5 mm; Voltage: 4-5 cells (max. 8V); BEC: 5V (1A); Switching outputs: 6; Servo outputs: 2; Motor outputs: 2; EasyBus outputs: 3; Bridgeable distance: up to 1.5 m; Maximum angle: approximately 90°. The KIEB 6/2/2 is a KraftwerK infrared receiver with bus outputs and 6 switching, 2 servo, and 2 motor outputs. With the KIEB 6/2/2 infrared receiver, you can control the trailer supports and a tipper or ramp via the two integrated motor outputs. Doors, lift axles, or steering axles can be controlled via the two servo outputs. Auxiliary lighting or rotating beacons can be controlled via the switching outputs. Bus extensions (switching, servo, or motor extensions) can be connected to the three bus outputs as usual.

Available immediately, delivery time: 1-4 days

Product number: 10446

€ 109,90 *

Subscriptions

1x XBSefect electronics, fully assembled 4 outputs each max.

1x XBSefect electronics, fully assembled, 4 outputs each with a maximum of 100mA, 15 different effects to choose from. BEC with 5V or external supply with 6 to 14 volts. Functions can be selected via remote control. RC flash electronics, fully assembled, 4 outputs each with a maximum of 100mA, 15 different effects to choose from (xenon light effect, flashing light, flashing light, permanent light and running light), BEC with 4,8 volts or external power supply of 6-14 volts, functions can be selected via remote control (3-way toggle switch or 3-way button with zero position in the middle 1-0-1) Size (lxwxh): approx. 35 x 22 x 15mm Weight: approx. 10 grams Contents: 1 electronic module 1 servo cable 1 jumper 1 power connection cable 1 instructions

Available immediately, delivery time: 1-4 days

Product number: 9575

€ 32,74 *

Subscriptions

EasyBus replacement cable 60cm long, 1-sided with post coupling

EasyBus replacement cable 60cm long. 1-sided with post coupling. 1 side open wire ends.

Available immediately, delivery time: 1-4 days

Product number: 12169

€ 2,98 *

Subscriptions

KIES infrared transmitter. Plug & Play solution

1x KIES infrared transmitter. Plug & Play solution. Incl. IR transmitter diode. Suitable for the EasyBus system. Technical data: - Dimensions 27,5x17x7,5 mm - Power supply via EasyBus - 1 servo output (adjustable) Scope of delivery: - 1x KIES infrared transmitter - 1x IR transmitter diode The infrared transmitter is simply plugged into a free connection on the EasyBus and is immediately ready for use. It not only transmits the light functions of EasyBus but also servo functions to the infrared receiver (not included). Items 9252 and 9253 are available as suitable infrared receivers.

Available immediately, delivery time: 1-4 days

Product number: 9254

€ 34,90 *

Subscriptions

2-way distributor (Kingbus system) with 15cm cables.

2-way distributor (Kingbus system) with 15cm cables. This distributor can be used to expand the Kingbus system with new light modules. It works like a multiple socket in the home. This 2-way distributor is very suitable for connecting two rear light modules and the infrared transmitter module at the rear of a tractor unit. This means that only one twin cable leads to the front to the central module. This distributor is available with different cable lengths: 15, 30 and 50 cm.

Available immediately, delivery time: 1-4 days

Product number: 10937

€ 8,50 *

Subscriptions

4 distribution board (Kingbus system) with 15cm cables

4-way distributor (Kingbus system) with 15cm cables. This distributor can be used to expand the Kingbus system with new light modules. It works like a multiple socket in the home. This 4-way distributor is very suitable for connecting two rear light modules and the infrared transmitter module at the rear of a tractor unit. This means that only one twin cable leads to the front to the central module. This distributor is available with different cable lengths: 15, 30 and 50 cm.

Available immediately, delivery time: 1-4 days

Product number: 10875

€ 9,50 *

Subscriptions

Steerable king pin for semi-trailers (Tamiya). For KingBus-S

Steerable king pin for trailer (Tamiya). For KingBus system. This king pin measures the articulation angle/steering angle between the towing vehicle and the semi-trailer. It is designed for installation in the Goldhofer semi-trailer low loader from Veroma/Carson. Of course, it can also be used for self-built vehicles! To mount this steerable king pin (LKB) on the model, the hole for the pin must be drilled larger. Otherwise, no further adjustments to the trailer are necessary. The connection cable with plug is designed for operation on the trailer module with additional functions (IRAM), article 11703. Technical data: Cable length: 150mm Potentiometer value: 5kOhm Connection: cable with plug

Ready to ship in 5 days, delivery time 1-4 days

Product number: 11702

€ 59,00 *

Subscriptions

Power station zone Infrared transmitter diode

Kraftwerk-Zone infrared transmitting diode, 5mm round. For KLM 4/16.

Available immediately, delivery time: 1-4 days

Product number: 11286

€ 9,90 *

Subscriptions

EasyBus replacement cable 80cm long, 1-sided with post coupling

EasyBus replacement cable 80cm long. 1-sided with post coupling. 1 side open wire ends.

Ready to ship in 14 days, delivery time 1-4 days

Product number: 12170

€ 2,98 *

Subscriptions

Trailer module for the Pistenking Kingbus system.

Trailer module to the Pistenking Kingbus system. This trailer module is a true all-rounder. It is connected to the tractor via infrared. For data transmission, an infrared transmitter module must be installed in the tractor. (Article 11704). In addition to the normal Kingbus light modules, two motors can also be connected to this trailer module. This allows, for example, the supports or ramps on the trailer are operated. Each motor can also be equipped with an end position switch. The necessary preparations have already been made. Only the limit switches have to be connected to the supplied cable. The module has an input for a potentiometer. This measures the articulation angle between the tractor and the semi-trailer. We offer a separate parts kit (11702) for this purpose. The steering axle control can be switched between "caster" and "reverse" (by pressing a button on the Kingpad). It is also possible to manually control the axles to the desired steering angle - also by pressing a button on the Kingpad! Furthermore, up to 16 LEDs (side marker lights) can be connected in series to the module. The luminosity can be continuously dimmed using the potentiometer on the module. The LEDs switch on with the parking lights. With an additional Kingpad, which is mounted on the trailer, the motors (supports/ramps) can be operated even without an infrared connection to the tractor unit. This is helpful if, for example, the tractor has already been stowed away after a day of driving, but the ramps on the trailer still need to be folded in. All of these special functions can be operated via the existing Kingpad. The "S key" can be used to switch to a second level. The buttons for the light functions are used for the special functions (supports, ramps, fifth wheel plate, steering axles). To explain the second level keys, a narrow sticker is included that describes their functions. This is glued to the Kingpad between the upper and lower row of keys. For more detailed explanation, a sticker in the original Kingpad size is also included. This can be stuck to a free space on the remote control. Please also note the connection plan. In addition to the infrared receiver unit, all cables and plugs are also included. Kingbus systems purchased from November 2015 already support the trailer functions! For "older" modules, we can install a software update on the Kingbus central module! Contact us... Inputs / Outputs: 2x Kingbus outputs for light modules, 2x motor drivers (speed controller on/off/on, with soft start) up to 5A load capacity, limit switch for motor drivers, 1x rotating beacon, input for fifth wheel potentiometer (measures articulation angle between tractor and semi-trailer), servo control for steered axles on the semi-trailer, Kingpad input on the trailer (for controlling motor drivers without connection to the tractor), up to 16 side marker lights in series without series resistor (parking lights), dimmable side marker lights, infrared receiver. Technical data: Operating voltage: 6-12 volts, module dimensions: 42 x 34 mm (L x W), cable lengths on the module: 200 mm

Ready to ship in 5 days, delivery time 1-4 days

Product number: 11703

€ 119,00 *

Subscriptions

4 distribution board (Kingbus system) with 50cm cables

4-way distributor (Kingbus system) with 50cm cables. This distributor can be used to expand the Kingbus system with new light modules. It works like a multiple socket in the home. This 4-way distributor is very suitable for connecting two rear light modules and the infrared transmitter module at the rear of a tractor unit. This means that only one twin cable leads to the front to the central module. This distributor is available with different cable lengths: 15, 30 and 50 cm.

Available immediately, delivery time: 1-4 days

Product number: 10876

€ 10,50 *

Subscriptions

Taillight Boards (Pair) for the 7 chamber taillights v

Rear light boards (pair) for the 7-chamber rear lights from Veroma/Carson. Kingbus system. Rear light modules for the 7-chamber rear lights from Veroma/Carson with just two cables. The light modules are delivered fully assembled and tested. They only need to be installed in the model. No adjustments to the housing are necessary! The lights can be controlled via the Kingpad (not included). The central module & Kingpad are not required for remote control systems from the brands Brixl, ScaleArt Commander and Blauzahn. Instead, the Kingbus interface is connected to the assigned receiver slot. This controls the light functions via the standard Kingbus cable!The Kingpad is not required in this case, as the light functions can be operated via switches and buttons on the remote control.Expanding the lighting system with new light modules is simple - just plug them in!Features:- Parking light- Rear fog light- Brake light via driving channel or Kingpad- Reversing light via driving channel or Kingpad- Left / right indicator- Indicator reset via steering channel- Hazard warning lightsScope of delivery:- 2 light modules (cable length 150mm each)Matching rear light housing (not included): Article 1905.

Available immediately, delivery time: 1-4 days

Product number: 10939

€ 78,99 *

Subscriptions

RC Multibus USB interface for the configuration of

RC Multibus USB interface to configure Kraftwerk modules without a light assistant. This article replaces article 11216! With this interface, Kraftwerk's RCMultiBus modules can be configured and tested with and without a receiver. The EasyBus modules can also be connected directly to this interface and configured without a BusMaster (such as KLM 4/16 or RS1). EasyBus systems installed in the model can be connected using the double-sided patch cable provided. The RCMultiBus currently includes EasyBus, IBUS, SBUS, SUMD V3, CPPM and UART.

Available immediately, delivery time: 1-4 days

Product number: 12046

€ 46,05 *

Subscriptions

Infrared transmitter module for Pistenking Kingbus system.

Infrared transmitter module for the Pistenking Kingbus system. The infrared transmitter module is simply plugged into the central module or a distributor using a standard Kingbus cable. It transmits the data from the truck to the trailer - wirelessly via infrared. A servo for unlocking the fifth wheel plate / trailer coupling can be connected to the second output. It can later be operated via the Kingpad. Kingbus systems purchased from November 2015 already support the trailer functions! A software update can be installed on "older" modules! Get in touch with us! Outputs: Connected infrared transmitter diode Connection for fifth wheel plate or coupling coupling release Technical data: Module dimensions: 34 x 12mm (L x W) Cable lengths: 150mm

Available immediately, delivery time: 1-4 days

Product number: 11704

€ 38,00 *

Subscriptions

4-way distributor (Kingbus system) with 30cm cables.

4 distribution board (Kingbus system) with 30cm cables.

Available immediately, delivery time: 1-4 days

Product number: 11263

€ 10,00 *

Subscriptions

EasyBus daytime running light replacement cable 10cm long 1-sided with P

EasyBus daytime running light replacement cable 10cm long 1-sided with post coupling. 1 side open strand ends.

Ready to ship in 14 days, delivery time 1-4 days

Product number: 12171

€ 2,59 *

Subscriptions

4-way distributor (Kingbus system) without cable.

Available immediately, delivery time: 1-4 days

Product number: 12449

€ 6,50 *

Subscriptions

1x KSB2 servo control. For EasyBus- system. To connect

1x KSB2 servo control. For EasyBus system. For connecting up to 2 servos This module expands your EasyBus system with 2 freely adjustable servo outputs. The KSB2 module does not require an additional power supply. Technical data: Dimensions: 28x40x11mm Supply voltage: via the EasyBus Servo outputs: 2 Details: Plug & Play solution 2 additional servo outputs for the EasyBus Adjustable via control panel Proportional functions (e.g. for steering servo) Digital functions (e.g. fifth wheel coupling, ramps or flaps) Center positions, rotation speeds and directions of rotation adjustable No programming knowledge required PC software can be downloaded free of charge The following functions can be implemented with this module: - Proportional function - Proportional function switched - Two positions - Two positions center position - Actuator - Hydraulic simulation - Fifth wheel plate - Trailer supports - Trough - Windscreen wiper - Searchlight

Available immediately, delivery time: 1-4 days

Product number: 9250

€ 38,90 *

Subscriptions

1x KMB1 - 10A speed controller for Easy-Bus system for Nebe

1x KMB1 - 10A speed controller for Easy-Bus system for auxiliary drives. The KMB 1-10A has a motor output with a load of 10A. It is intended for auxiliary drives and, thanks to the two connections for limit switches, is also ideal for spindle drives. Dimensions 34x23x12mm

Available immediately, delivery time: 1-4 days

Product number: 9251

€ 39,89 *

Subscriptions

1x BUS - distributor with 3,5mm jack. With this distributor la

1x BUS distributor with 3,5mm jack. With this distributor, the EasyBus outputs can be plugged into the trailer via a jack socket. Plug & Play solution.1x BUS distributor with 3,5mm jack. With this distributor, the EasyBus outputs can be plugged into the trailer via a jack socket. Plug & Play solution.

Available immediately, delivery time: 1-4 days

Product number: 9256

€ 24,89 *

Subscriptions

EasyBus replacement LED with 60cm cable. LED 3mm yellow with 60cm

EasyBus replacement LED with 60cm cable. LED 3mm clear, glowing yellow with 60cm strands and open strand ends. Suitable for side marker lights and lighting boards.

Available immediately, delivery time: 1-4 days

Product number: 12461

€ 4,30 *

Subscriptions

Kraftwerk-Zone infrared transmitter diode 5mm round. For GRAVEL.

Ready to ship in 14 days, delivery time 1-4 days

Product number: 11348

€ 9,90 *

Subscriptions

EasyBus replacement LED with 15cm cable. LED 3mm clear, white light

EasyBus replacement LED with 15cm cable. 3mm clear LED, white light with 15cm wires and open wire ends. Suitable for side marker lights and lighting boards.

Available immediately, delivery time: 1-4 days

Product number: 13167

€ 3,90 *

Subscriptions

1x KSB4 servo control. For EasyBus- system. To connect

1x KSB4 servo control. For EasyBus system. For connecting up to 4 servos. This module expands your EasyBus system by 4 freely adjustable servo outputs. The KSB4 module must also be provided with a power supply. The VCC cable is either routed to a free receiver output or connected to an external battery.Technical data:Dimensions: 24x20x6mmSupply voltage: 4-5 cells NiMH (max. 8V)Servo outputs: 4Details:Plug & Play solutionFour additional servo outputs for the EasyBusAdjustable via control panelProportional functions (e.g. for steering servo)Digital functions (e.g. fifth wheel, ramp or flaps)Center positions, rotation speeds and rotation directions adjustableNo programming knowledge requiredPC - software can be downloaded free of chargeThe following functions can be implemented with this module:-Proportional function-Proportional function switched-Two positions-Two positions center position-Actuator-Hydraulic simulation-Fifth wheel plate-Trailer supports-Trough-Windscreen wiper-Searchlight

Available immediately, delivery time: 1-4 days

Product number: 9249

€ 38,90 *

Subscriptions

Kingbus connector with 15 cm wire. Suitable for the Kingbus system

Kingbus connector with 15 cm wire. 2-pin. Suitable for the Kingbus system.

Available immediately, delivery time: 1-4 days

Product number: 13314

€ 1,99 *

Subscriptions

RC Multibus USB-Interface for the configuration of Kraftwer

RC Multibus USB interface to be able to configure power plant modules without a light assistant. With jack plug connection.

Available immediately, delivery time: 1-4 days

Product number: 12044

€ 56,31 *

Subscriptions

KLM 4 / 16 light assistant SET incl.LED cable harnesses

1x KLM 4/16 light assistant set incl. LED wiring harnesses. The lighting assistant is the core component of a lighting system that can be expanded as required. Incl. Transmitting diode. Plug & Play solution. Core component of the lighting system, compatible with all sound modules, speed controllers and the Tamiya MFU-xx. The EasyBus lighting systems are equipped with different lighting boards, IR trailer lighting, etc. expandable.Includes LED wiring harnesses (for 12V!) for front and rear lighting.The PC software can be downloaded free of charge. No programming knowledge is required. The control can be customized down to the smallest detail. Technical data: - Dimensions 51x36x13 mm - 4 inputs (steering, throttle, channel 1, channel 2) - 2 servo outputs (steering servo, speed controller) - 5 bus outputs (for expansion modules) - 16 switching outputs with max. 500mA, freely configurable-1x USB socket (Micro-USB, for configuration)From April 2018 incl. Transmitter diodeWe are of course happy to configure the lighting system according to your ideas and also save them.The KLM 4/16 light assistant is the further development of the KLM 4/12-500. Compact design, easy operation and compatibility with the most common systems on the market are its main strengths. It is compatible with standard forward-reverse speed controllers (with or without a separate brake), with the cruise control controllers from Servonaut and all sound modules. The light functions can be controlled in a variety of ways; please refer to the manual for details. The module, which is only 52 x 36 x 13 mm in size, offers eight high-current outputs (500 mA each and eight switching outputs with integrated series resistors), four adjustable servo outputs, an infrared output, a USB socket that is only required for configuration and five bus outputs, via which the system can be expanded as required with additional switching, servo or motor functions. Standard assignment of the outputs:-Output 1 & 2: parking light & high beam & headlight flasher-Output 3 & 4: dipped beam-Output 5: left indicator-Output 6: right indicator-Output 7 & 8: tail light & brake light-Output 9: rear fog light-Output 10: reversing light-Output 11 & 12: speed camera-It is possible to select the behavior of each individual output completely independently and freely via PC and to configure it on a percentage basis. In addition to some effect lighting, you can choose from all the usual lighting functions in the original: -- combined front light (parking light, low beam, high beam, headlight flasher and fog light) -- combined rear light (parking light, brake light, -- American rear light (parking light, brake light, indicator) -- daytime running light with automatic lowering when the indicator is activated -- cornering light -- curve light -- reversing light -- indicator, hazard warning light, American indicator -- multi-flashing light -- running light -- rotating light -- KnightRider In addition to the basic behavior of the individual outputs, the brightness, the switching on and off speed, and the switching on and off duration for the flashing functions can also be set. How easy this is can be tested in advance using the demo mode of the free PC software ControlPanel. The module is connected to four channels of the receiver. In addition to gas and steering, two channels (K1 and K2) are used to control the lighting. Please refer to the manual for the different variants! During development, special attention was paid to ease of use. You do not need any electronic experience to use this system! You will find all the information you need in the included quick start guide! Scope of delivery: 1x KLM 4/16 light assistant, 1x 12V LED wiring harnesses for front, 1x 12V LED wiring harnesses for rear

Ready to ship in 14 days, delivery time 1-4 days

Product number: 11174

€ 164,99 * € 172,28 * (4.23% saved)

Subscriptions

Taillight Boards (Pair) for AROCS 3348 by Tamiya.

Rear light boards (pair) for AROCS 3348 from Tamiya. Kingbus system. Rear light modules for the Mercedes-Benz Arocs 3348 from Tamiya with just two cables. (Rear tipper).The light modules are delivered fully assembled and tested.They only need to be installed in the model. No adjustments to the housing are necessary!The lights can be controlled via the Kingpad (not included).The central module & Kingpad are not required for remote control systems from the brands Brixl, ScaleArt Commander and Blauzahn.Instead, the Kingbus interface is connected to the assigned receiver slot. This controls the light functions via the standard Kingbus cable!The Kingpad is not required in this case, as the light functions can be operated via switches and buttons on the remote control.Expanding the lighting system with new light modules is simple - just plug them in!Features:- Parking light- Rear fog light- Brake light via driving channel- Reversing light via driving channel or Kingpad- Left / right indicator- Indicator reset via steering channel- Hazard warning lightsScope of delivery:- 2 light modules (cable length 150mm each)

Available immediately, delivery time: 1-4 days

Product number: 11059

€ 78,99 *

Subscriptions

Front headlight circuit boards (pair) for AROCS by Tamiya

Headlight circuit boards (pair) for Tamiya Arocs models. Kingbus system. Headlight modules for the Tamiya Mercedes-Benz Arocs with only two wires. The light modules are delivered fully assembled and tested. They simply need to be installed in the model. No modifications to the body are necessary! The lights can be controlled via the Kingpad (not included). For Brixl, ScaleArt Commander, and Bluetooth radio control systems, the central module and Kingpad are not required. Instead, the Kingbus interface is connected to the designated receiver port. This controls the lighting functions via the standard Kingbus cables! The Kingpad is not required in this case, as the lighting functions can be operated via switches and buttons on the remote control. Expanding the lighting system with new light modules is simple – just plug them in! Features: Parking lights, Low beam (only with parking lights), High beam (latching, only with low beam), Flash-to-pass, Fog lights, Left/right turn signals, Turn signal cancellation via steering channel, Hazard lights, Automatic cornering lights when steering or indicating, Xenon effect! Scope of delivery: 2 light modules (cable length 150mm each), 4 LEDs for turn signals and position lights (pluggable), Fiber optic cable for daytime running lights, 2 fiber optic cable housings

Ready to ship in 5 days, delivery time 1-4 days

Product number: 11057

€ 98,00 *

Subscriptions

Headlight boards (pair) for MAN from Tamiya. Kin

Headlight boards (pair) for MAN from Tamiya. Kingbus system. Headlight modules for the Mercedes-Benz Actros GigaSpace from Tamiya with just two cables.The light modules are delivered fully assembled and tested. They only need to be installed in the model. No adjustments to the housing are necessary!The lights can be controlled via the Kingpad (not included).The central module & Kingpad are not required for remote control systems from the brands Brixl, ScaleArt Commander and Blauzahn.Instead, the Kingbus interface is connected to the assigned receiver slot. This controls the light functions via the standard Kingbus cable!The Kingpad is not required in this case, as the light functions can be operated via switches and buttons on the remote control.Expanding the lighting system with new light modules is simple - just plug them in!Features:- Parking light- Low beam (only with parking light)- High beam (latching only with low beam)- Headlight flasher- Fog light- Left / right indicator- Indicator reset via steering channel- Hazard warning lights- Automatic cornering light when steering or blinking- Xenon effect!Scope of delivery:- 2 light modules (cable length 150mm each)- 4 LEDs for indicators and position lights (plug-in)

Ready to ship in 5 days, delivery time 1-4 days

Product number: 11056

€ 98,00 *

Subscriptions

Infrared receiver diode for the Pistenking Kingbus system 3-pin

Infrared receiver diode for the Pistenking Kingbus system. Original spare part with 3-pin SH socket. 1 piece. Replacement diode for the IRAM module.

Available immediately, delivery time: 1-4 days

Product number: 13319

€ 7,15 *

Subscriptions

Kingbus connector with 30 cm wire. Suitable for the Kingbus system

Kingbus connector with 30 cm wire. 2-pin. Suitable for the Kingbus system.

Available immediately, delivery time: 1-4 days

Product number: 13315

€ 2,50 *

Subscriptions

Kingbus connector with 50 cm wire. Suitable for the Kingbus system

Kingbus connector with 50 cm wire. 2-pin. Suitable for the Kingbus system.

Available immediately, delivery time: 1-4 days

Product number: 13316

€ 2,99 *

Subscriptions

Taillight Boards (Pair) for the 6 chamber taillights v

Rear light boards (pair) for the 6-chamber rear lights from Veroma/Carson. Kingbus system. Rear light modules for the 6-chamber rear lights from Veroma/Carson with just two cables. The light modules are delivered fully assembled and tested. They only need to be installed in the model. No adjustments to the housing are necessary! The lights can be controlled via the Kingpad (not included). The central module & Kingpad are not required for remote control systems from the brands Brixl, ScaleArt Commander and Blauzahn. Instead, the Kingbus interface is connected to the assigned receiver slot. This controls the light functions via the standard Kingbus cable!The Kingpad is not required in this case, as the light functions can be operated via switches and buttons on the remote control.Expanding the lighting system with new light modules is simple - just plug them in!Features:- Parking light- Rear fog light- Brake light via driving channel or Kingpad- Reversing light via driving channel or Kingpad- Left / right indicator- Indicator reset via steering channel- Hazard warning lightsScope of delivery:- 2 light modules (cable length 150mm each)Matching rear light housing (not included): Article 3134.

Available immediately, delivery time: 1-4 days

Product number: 10938

€ 78,99 *

Subscriptions

Infrared transmitter diode for Pistenking Kingbus system with plug

Infrared transmitter diode for the Pistenking Kingbus system. Original spare part with IR servo plug. 1 piece. Replacement diode for the infrared transmitter module from Pistenking.

Available immediately, delivery time: 1-4 days

Product number: 13318

€ 7,15 *

Subscriptions

Taillight boards (pair) for MAN from Tamiya. Kingbus-Sys

Rear light boards (pair) for MAN from Tamiya. Kingbus system. Rear light modules for the MANs from Tamiya with just two cables. The light modules are delivered fully assembled and tested. They only need to be installed in the model. No adjustments to the housing are necessary! The lights can be controlled via the Kingpad (not included). The central module & Kingpad are not required for remote control systems from the brands Brixl, ScaleArt Commander and Blauzahn. Instead, the Kingbus interface is connected to the assigned receiver slot. This controls the light functions via the standard Kingbus cable!The Kingpad is not required in this case, as the light functions can be operated via switches and buttons on the remote control.Expanding the lighting system with new light modules is simple - just plug them in!Features:- Parking light- Rear fog light- Brake light via driving channel- Reversing light via driving channel or Kingpad- Left / right indicator- Indicator reset via steering channel- Hazard warning lightsScope of delivery:- 2 light modules (cable length 150mm each)

Available immediately, delivery time: 1-4 days

Product number: 11058

€ 78,99 *

Subscriptions

American roof lighting. KLB8-20. Ready to install wired

American roof lighting. KLB8-20. Ready-to-install wired yellow LEDs (5). For Kraftwerk EasyBus system. Suitable for Tamiya Cascadia, GrandHauler, KingHauler.

Ready to ship in 14 days, delivery time 1-4 days

Product number: 11050

€ 59,77 *

Subscriptions

Headlight PCBs (Pair) for ACTROS from Tamiya

Headlight circuit boards (pair) for ACTROS from Tamiya. Kingbus system. Suitable for Actros 1851 and 3363. Headlight modules for the Mercedes-Benz Actros GigaSpace from Tamiya with just two cables. Suitable for the Actros 1851 and Actros 3363. The light modules are delivered fully assembled and tested. They simply need to be installed in the model. No modifications to the housing are necessary! The lights can be controlled via the Kingpad (not included). The central module and Kingpad are not required for remote control systems from the Brixl, ScaleArt Commander, and Bluetooth brands. Instead, the Kingbus interface is connected to the designated receiver slot. This controls the lighting functions via the standard Kingbus cable! The Kingpad is not required in this case, as the lighting functions can be operated via switches and buttons on the remote control. Expanding the lighting system with new light modules is simple - simply plug it in! Features: - Parking light - Low beam (only with parking light) - High beam (latching only with low beam) - High beam flasher - Fog light - Left/right indicator - Indicator reset via steering channel - Hazard warning lights - Automatic cornering light when steering or signaling - Xenon effect! Scope of delivery: - 2 light modules (cable length 150mm each) - 4 LEDs for indicators and position lights (pluggable) - Fiber optic cable for daytime running light - 2 fiber optic cable housings

Available immediately, delivery time: 1-4 days

Product number: 10873

€ 98,00 *

Subscriptions

Taillight boards (pair) for ACTROS from Tamiya

Rear light circuit boards (pair) for the ACTROS 1851/3363 and AROCS 3363 from Tamiya. Kingbus system. Rear light modules for the Mercedes-Benz Actros GigaSpace and the Arocs 3363 from Tamiya with just two cables. The light modules are delivered fully assembled and tested. They simply need to be installed in the model. No modifications to the housing are necessary! The lights can be controlled via the Kingpad (not included). The central module and Kingpad are not required for remote control systems from the Brixl, ScaleArt Commander, and Bluetooth brands. Instead, the Kingbus interface is connected to the designated receiver slot. This controls the lighting functions via the standard Kingbus cable! The Kingpad is not required in this case, as the lighting functions can be operated via switches and buttons on the remote control. Expanding the lighting system with new light modules is simple - simply plug them in! Features: - Parking light - Rear fog light - Brake light via drive channel - Reversing light via drive channel or Kingpad - Left/right turn signals - Turn signal reset via steering channel - Hazard warning lights Scope of delivery: - 2 light modules (cable length 150mm each)

Available immediately, delivery time: 1-4 days

Product number: 10874

€ 78,99 *

Subscriptions

Headlight boards (pair) for SCANIAs from Tamiya.

Headlight boards (pair) for SCANIAs from Tamiya. Kingbus system. Headlight modules for the Scanias from Tamiya with just two cables.The light modules are delivered fully assembled and tested. They only need to be installed in the model. No adjustments to the housing are necessary!The lights can be controlled via the Kingpad (not included).The central module & Kingpad are not required for remote control systems from the brands Brixl, ScaleArt Commander and Blauzahn.Instead, the Kingbus interface is connected to the assigned receiver slot. This controls the light functions via the standard Kingbus cable!The Kingpad is not required in this case, as the light functions can be operated via switches and buttons on the remote control.Expanding the lighting system with new light modules is simple - just plug them in!Features:- Parking light- Low beam (only with parking light)- High beam (latching only with low beam)- Headlight flasher- Fog light- Left/right indicator- Indicator reset via steering channel- Hazard warning lights- Automatic cornering light when steering or blinking- Xenon effect!Scope of delivery:- 2 light modules (cable length 150mm each)

Available immediately, delivery time: 1-4 days

Product number: 11062

€ 98,00 *

Subscriptions

Taillight Boards (Pair) for SCANIAs from Tamiya. Kingbus

Rear light boards (pair) for SCANIAs from Tamiya. Kingbus system. For Scania R470 and R620 from Tamiya. Rear light modules for the SCANIAs from Tamiya with just two cables. The light modules are delivered fully assembled and tested. They only need to be installed in the model. No adjustments to the housing are necessary! The lights can be controlled via the Kingpad (not included). The central module & Kingpad are not required for remote control systems from the brands Brixl, ScaleArt Commander and Blauzahn. Instead, the Kingbus interface is connected to the assigned receiver slot. This controls the light functions via the standard Kingbus cable!The Kingpad is not required in this case, as the light functions can be operated via switches and buttons on the remote control.Expanding the lighting system with new light modules is simple - just plug them in!Features:- Parking light- Rear fog light- Brake light via driving channel- Reversing light via driving channel or Kingpad- Left / right indicator- Indicator reset via steering channel- Hazard warning lightsScope of delivery:- Inserts for rear lights in white- 2 light modules (cable length 150mm each)

Available immediately, delivery time: 1-4 days

Product number: 11063

€ 78,99 *

Subscriptions

Filter products