Tilt drive

1 engine f. Tilting drive (spindle motor) 6V (3-9V) 300U / min

1 motor for tilt drive (spindle motor) 6V (3-9V) 300rpm. Idle 500mA. Current max. 2A. Reduction ratio 50:1. 125 gr. (shipping weight 155gr.). 907066. Diameter 27,5mm/33mm (motor/gearbox). Shaft diameter 5mm flattened to 4mm. Shaft 12mm long.Motor length: 38/44mm (without/with connections)Gearbox length: 20mm.Recommended motor for the tilt spindle item 4099!Suitable as a drive for the mast double spindle of the crawler loader LR634, Carson, item 7575.You can find a suitable universal motor mount for this gear motor under item number 10697.Technical specifications:Nominal voltage: 6V DCWorking voltage: 3-9V DCIdle speed: 300rpmIdle current: 500mASpeed in continuous operation: 270rpmContinuous current: 2AContinuous torque: 200mNmPeak torque: 600mNmReduction ratio: 50:1Weight: 125gr.

Available immediately, delivery time: 1-4 days

Product number: 4218

€ 52,90 * € 55,99 * (5.52% saved)

Subscriptions

1x High tipping mechanism with threaded spindle for WDC

1x High-quality tipping mechanism with threaded spindle, suitable for WDC and TAM scales. For building construction site tippers. Toggle lever. Drive motor is NOT included. (Standard bore = 5mm). Scope of delivery: 2x toggle levers, 6mm aluminum; 6x ball bearings; 2x stainless steel shafts; toggle lever bearing and cylinder mount; 1x M8 threaded spindle with steel universal joint 13x40mm; 1x steel cylinder replica 12mm with internal thread; 1x cylinder head with brass bushing, pre-assembled; 2x spacers for frame/spindle mechanism; spindle stroke 88mm. Width (outer surfaces of the toggle levers): 40 mm. The tipping speed is determined by the selected motor/gear ratio. When ordering, please specify the desired diameter of the motor-side bore in the universal joint! If no bore diameter is specified, we will supply a 5 mm bore! Customers have already used the following motors with this item: Item numbers 4218, 6409, 6187, 6184, 6185, 6186. Maximum dimension: 188 mm (end of universal joint to center of tipping point, fully retracted). A suitable motor mount for motor 4218 is available under item number 10697.

End of life - article no longer available!

Product number: 5922

€ 114,95 *

Subscriptions

configure now

1x Engine mount, suitable for geared motor Article 4218 and 75

1x motor bracket, suitable for gear motor items 4218 and 7577. Universal bracket with screws for fastening the motor. Suitable for vehicle frames with a width of 60mm. Motor bracket, bracket made of 2mm stainless steel. Suitable for gear motors with item numbers 4218, 7577. Suitable for fastening to vehicle frames with a width of approx. 60mm. The bracket allows 2 different installation situations for the motor. Either the output shaft is downwards or upwards.

Available immediately, delivery time: 1-4 days

Product number: 10697

€ 9,75 *

Subscriptions

1x tilt drive motor (spindle drive) matching products

1x tilt drive motor (spindle drive) suitable for item 8535. For 7,2V. 907166. For the lifting drive of the Fliegl tipper. Recommended controller for the tilt motor: THOR14LF (item 11689) - not included. This gear motor is used for the tilt drive of the Fliegel rear tipper and the gooseneck trailer.

Available immediately, delivery time: 1-4 days

Product number: 8536

€ 79,94 * € 84,99 * (5.94% saved)

Subscriptions

Spare spindle for tilting drive Article 8535. spare part

1x replacement spindle for tilt drive item 8535. Fully assembled threaded tube. Consists of spindle tube with base, brass threaded nut. Fliegl spare part. MS threaded nut 8mm (fine).

Available immediately, delivery time: 1-4 days

Product number: 10549

€ 24,20 *

Subscriptions

CARSON Tuning Spindle for Tamiya Drive Unit

CARSON tuning spindle for the drive set of the Tamiya tilting unit. Reduces the lifting time by approx. 25%. Accelerates the lifting speed.

Available immediately, delivery time: 1-4 days

Product number: 11218

€ 38,98 * € 40,99 * (4.9% saved)

Subscriptions

1 tilt drive (spindle drive) e.g. for Carson

1 tilt drive (spindle drive) e.g. for Carson dump truck FLIEGL StoneMaster. Pre-assembled tilt drive (without motor). (Shipping weight 650g). 907217. Special spindle tilt drive for the dump trailer FLIEGL StoneMaster from Carson. (Motor not included). Also suitable for 2-axle tipping central axle trailers (new in 2019). Suitable motor: item 8536.

Ready to ship in 5 days, delivery time 1-4 days

Product number: 8535

€ 189,00 * € 210,00 * (10% saved)

Subscriptions

1 tilt drive (spindle drive) e.g. for Carson

1 tilt drive (spindle drive) e.g. for Carson dump truck. Pre-assembled tilt drive (without motor). (907056) (shipping weight 520g). Recommended motor: item 4218.

Available immediately, delivery time: 1-4 days

Product number: 4099

€ 159,00 * € 185,00 * (14.05% saved)

Subscriptions

Replacement spindle for tilting drive products 4099. complete monti

1x replacement spindle for tilt drive item 4099. Fully assembled replacement spindle. Consists of spindle tube with base, spindle with connection, compression spring.

Available immediately, delivery time: 1-4 days

Product number: 9967

€ 51,91 *

Subscriptions

Tilting spindle drive SPIN4151 1:14 Tilting unit for Tamiya

Tilt spindle drive SPIN4151 1:14 Tilt unit for Tamiya Arocs 4151 rear tipper. Aluminum parts, screwed Assembly pre-assembled and wired, black powder-coated. MF8 recommended Tilt unit for Tamiya Arocs 4151 rear tipperAluminum parts, screwedTrapezoid spindle, rear mount with ball bearing7,2V to 12V motor with gearLimit switch (up to 3A) wired for both end positions we recommend the mini speed controller MF8 for operationAssembly pre-assembled and wired, black powder-coatedDimensions approx. 62 x 380mmfor frame width 63mmParts black powder-coatedTipping speed at 7,2V: 26 secondsTipping speed at 12V: 16 seconds

Available immediately, delivery time: 1-4 days

Product number: 12240

€ 318,99 *

Subscriptions

Filter products