Transmission

PAGE

1x planetary gear metal 6: 1. (224503)

1x planetary gear metal 6:1. Output shaft 4mm diameter, 11mm long. Input gear with 3,2mm bore. (224503). The gear fits all motors that have an identical mounting hole pattern such as TruckPuller3, Venom, TM72, TM120, original Tamiya kit motor and similar. Maximum input speed 10.000 rpm. Please grease the gear! Scope of delivery: Gear as described Input gear Fastening screws Outer diameter without threaded ends: 40mm Length without shaft output: 48mm Output shaft: 4mm without flat, 11,5mm long

Ready to ship in 5 days, delivery time 1-4 days

Product number: 1783

€ 27,39 * € 27,40 * (0.04% saved)

Subscriptions

GM32U450-VTG 12V planetary gear motor 450rpm. With

GM32U450-VTG 12V planetary gear motor 450 rpm. With quiet, robust planetary gear. As a drive motor for models with underfloor drive. WITH DISTRIBUTION GEAR! Permanent, not switchable. Motor data:Voltage: 12VPoles: 5Interference suppression: yesIdle speed: 10.000 rpmIdle current: 800 mANominal speed: 8.700 rpmNominal current: 4,7 ANominal torque: 4,2 NcmNominal power: 38,0 WShort-term max. load speed: 5000 rpmShort-term max. load current: 15 AShort-term max. load torque: 16,5 NcmShort-term max. load power: 88 WBlocking current: 30 ABlocking torque: 33 NcmData for motor with gearbox:Reduction ratio: 14:1Diameter: 37mmLength: 85,6 mmWidth of distribution block: 32mmWeight: 362 gShaft diameter: 5mmIdle speed: 520 rpmNominal speed: 450 rpm.Nominal torque: 54,9 NcmShort-term max. load torque: 88 NcmMax. torque: 120 NcmSupplied fully assembled with mounting bracket.Shaft outputs: 5mm diameter.

Available immediately, delivery time: 1-4 days

Product number: 7883

€ 172,99 *

Subscriptions

1x reduction gear 4: 1 Carson. Lightweight

1x reduction gear 4:1 Carson. Light plastic housing with ball-bearing metal gears. To increase the torque and reduce the speed. Suitable for all Tamiya tractors, except GlobeLiner! The shafts have an outer diameter of 5mm with a flattening to 4mm. A suitable cardan attachment (not included) is required. Cardan attachment: Article 10795.

Available immediately, delivery time: 1-4 days

Product number: 9199

€ 37,98 * € 48,99 * (22.47% saved)

Subscriptions

Transmission mount for 3-speed gearbox horizontal installation

Gearbox bracket for 3-speed gearbox, horizontal installation. With this holder, the gearbox hangs in the frame (output below). (251110). Hole spacing approx 39mm. ** DISCONTINUED ITEM!

No longer available

Product number: 1735

€ 8,22 *

Subscriptions

Details

Cardan Set 60-200mm -ScaleDRIVE-

1x Cardan Set Scale Drive. adjustable from 60-210mm. For diameters 4mm and 5mm shaft, aluminum shot.

Available immediately, delivery time: 1-4 days

Product number: 9638

€ 168,49 *

Subscriptions

1x torque set for Tamiya Schaltgetr- ove. Pinion

1x torque set for Tamiya manual gearbox. Motor pinion with 8 teeth and metal gearbox face plate. 500907115. This expansion kit increases the torque by approx. 20%, the driving speed slows down accordingly. The smaller motor pinion increases the torque by approx. 20% and the speed is reduced accordingly.

Available immediately, delivery time: 1-4 days

Product number: 7940

€ 19,99 * € 23,99 * (16.67% saved)

Subscriptions

GM32U390-VTG 7,2V planetary gear motor 390U / min. With

GM32U390-VTG 7,2V planetary gear motor 390 rpm. With quiet, robust planetary gear. As a drive motor for models with underfloor drive. WITH DISTRIBUTION GEAR! Permanent, not switchable. Motor data:Voltage: 7,2VPoles: 5Interference suppressed: yesData for motor with gear:Reduction ratio: 14:1Diameter: 37mmLength: 85,6 mmWeight: 362 gShaft diameter: 6mmIdle speed: 470 rpmNominal speed: 390 rpmNominal torque: 34,6 NcmShort-term max. load speed: 226 rpmShort-term max. load torque: 95 NcmMax. torque: 140 NcmSupplied fully assembled with mounting bracket.Shaft outputs: 5mm diameter.

Available immediately, delivery time: 1-4 days

Product number: 9262

€ 172,99 *

Subscriptions

1x Pinion, 12 teeth, brass. Gear width 11mm. 1x

1x Pinion, 12 teeth, brass. Gear width 11mm. 1x threaded cross bore M3 for mounting. Interior 4,2mm. Pinion for Wedico 3-speed four-wheel drive transmission.

Available immediately, delivery time: 1-4 days

Product number: 5631

€ 11,27 * € 11,65 * (3.26% saved)

Subscriptions

1x motor pinion 12 teeth, plastic, yellow. Gear width 8m

1x motor pinion 12 teeth, plastic, yellow. Gear width 8mm. Bore 4mm with flattening for motor axle. Motor pinion for Wedico adapter. Total width 8mm. Diameter 11mm.

Available immediately, delivery time: 1-4 days

Product number: 11314

€ 4,71 *

Subscriptions

Planetary gear metal 3: 1. (215589)

Planetary gear metal 3:1. (215589) Output: 4mm diameter, 11mm long. Input: gear with 3,2mm bore. The gear fits all motors that have an identical mounting hole pattern such as TruckPuller3, Venom, TM72, TM120, original Tamiya kit motor and similar. Maximum input speed 10.000 rpm. Please grease the gear! Scope of delivery: Gear as described Input gear Fastening screws Outer diameter without threaded ends: 40mm Length without shaft output: 48mm

Available immediately, delivery time: 1-4 days

Product number: 2619

€ 26,86 * € 27,40 * (1.97% saved)

Subscriptions

1x Pinion, plastic, white. Gear width 8mm. Bohru

1x motor pinion, plastic, white. Gear width 8mm. Bore 4mm with flattening for Bühler motor. 14 teeth. Motor pinion for Wedico standard gears. Total width 10mm. Diameter 13mm. Modulus: 0,8

Available immediately, delivery time: 1-4 days

Product number: 9890

€ 4,36 *

Subscriptions

1x motor pinion, 12 teeth, plastic. Gear width 11mm

1x motor pinion, 12 teeth, plastic. Gear width 11mm. 1x threaded cross hole M3 for fastening. Inside 4,2mm. Motor pinion for Wedico 3-speed all-wheel drive transmission. Black. This pinion is also used when using the Wedico double motor transmission.

Available immediately, delivery time: 1-4 days

Product number: 10708

€ 4,65 *

Subscriptions

Motor flange with pinion for LRP, Carson, TruckPuller

Motor flange with pinion for LRP, Carson, TruckPuller. (251140). Mounting bolt circle 25mm. Also suitable for Truckmotor Truck Torque (10058).

Available immediately, delivery time: 1-4 days

Product number: 1833

€ 9,98 * € 10,40 * (4.04% saved)

Subscriptions

Transfer cases for four-wheel, switchable with holder, 1x

Transfer case for all-wheel drive, with holder, switchable, 1x input, 2x output 1:1 (251190), without further reduction Dimensions: 30x34x47 (WxLxH) without holder. All shaft inputs and outputs 5mm diameter with flattening. Shaft stub 10mm long. Suitable for vehicles 1:16 to 1:10 (Wedico and Tamiya scale). The transfer case is delivered with a mounted holder. The drive to the front can be switched on or off using a servo (not included). Housing made of aluminum 6-fold ball bearings Reduction 1:1 Input and output shaft 5mm with flattening Hardened gears Front axle switchable (via servo, not included) With retaining bracket (62mm wide) Suitable for frame widths of 60 - 63mm Dimensions: 54x30x57mm

Available immediately, delivery time: 1-4 days

Product number: 2616

€ 108,89 * € 109,00 * (0.1% saved)

Subscriptions

1 transfer box VTG for Servonaut GM32 gearmotors

1 transfer case VTG for Servonaut GM32 gear motors. Outputs: 5mm. Transfer case, permanent, not switchable. With mounting bracket and motor pinion. Dimensions: 35x50x25mm without shaft outputs. Completely ball bearing mounted.

Available immediately, delivery time: 1-4 days

Product number: 8152

€ 95,00 *

Subscriptions

Distributor -caleDRIVE- 2,65: 1

Transfer case, kit, ScaleDRIVE 6-fold ball bearing, ratio 2,65:1, milled steel gears. All shafts and screws made of stainless steel. The shafts have a diameter of 4mm with a flattening.Technical data:Total height: 54mmTotal width (at the mounting flange): 56mmDistance between the shaft connections: 30mm (center-center)Installation depth: 16mmLength of the shaft connections: 5,5mmReduction ratio: 2,65:16-fold ball bearingShaft diameter: 4mm

Available immediately, delivery time: 1-4 days

Product number: 9639

€ 51,99 *

Subscriptions

3-speed gearbox without motor / flange (251100)

3-speed manual gearbox without motor/flange (251100). All metal. Output shaft 5mm. Various motors can be used with various flange adapters (not included!).Reduction ratios:1st gear: 22,65:12nd gear: 11,32:13th gear: 5,66:1The manual gearbox can be attached horizontally or hanging in the frame, depending on the space available. The gearbox holder: - 1734 (the gearbox is located between the frame profiles) is available for this purpose (not included).As standard, the gearbox is screwed onto the frame side members using the mounting brackets that are integrated in the gearbox housing. No additional bracket is required for this.The gearbox is mounted, the motor and the matching flange are attached to the gearbox from the outside using 2 clamps. Shifting is done using a servo. The max. input speed is 6.500 rpm.

Available immediately, delivery time: 1-4 days

Product number: 2489

€ 189,00 * € 192,50 * (1.82% saved)

Subscriptions

1 planetary gear plastic 6: 1 (224504)

1 planetary gear plastic 6:1. Output shaft 4mm diameter, 11mm long. Input gear with 3,2mm bore. (224504). The gear fits all motors that have an identical mounting hole pattern such as TruckPuller3, Venom, TM72, TM120, original Tamiya kit motor and similar. Maximum input speed 10.000 rpm. Please grease the gear! Scope of delivery: Gear as described Input gear Fastening screws Outer diameter without threaded ends: 40mm Length without shaft output: 48mm

Available immediately, delivery time: 1-4 days

Product number: 2493

€ 15,51 * € 16,40 * (5.43% saved)

Subscriptions

Gear holder metal f.Planetengetriebe (224501)

Gearbox holder metal f.Planetengetriebe (224501). With 2 holes 3,2mm at a distance of 25mm. 2 screws M3x10mm in the scope of delivery.

Available immediately, delivery time: 1-4 days

Product number: 2494

€ 6,00 *

Subscriptions

Aluminium 2-speed transfer case to fit Tamiya

1x aluminum 2-speed transfer case suitable for Tamiya scale. 500907266. The CARSON drive concept for TAMIYA® trucks in 1:14 scale. Convert your TAMIYA 2- or 3-axle TAMIYA tractor into an all-round all-wheel drive vehicle with our self-locking axles. The components can be easily replaced as they are attached to the existing mounting points. A huge advantage of these axles is that no additional space is needed for a switching servo (linkages and Bowden cables), as they lock independently/automatically in the event of a loss of traction. Officially licensed by ZF Friedrichshafen AG.You decide how you want to convert your 2- or 3-axle tractor, this is possible in two stages:Configuration options for:2-axle tractors:Mercedes-Benz Actros Gigaspace 1845, MAN TGX 18.540, SCANIA R470, VOLVO FH12, Mercedes-Benz 1838LS, Mercedes-Benz 18501, 4x2 rear axle drive (with self-locking differential)- TAMIYA® 3-speed manual transmission (modular kit) with a CARSON rear axle (self-locking)2, 4x4 all-wheel drive with 2+2 speed transmission (front axle/rear axle/transfer case self-locking)- CARSON 2-speed manual transmission Compact in conjunction with the CARSON 2-speed transfer case torque compensation (self-locking), driven front axle (self-locking), rear axle (self-locking), drive shaft set 4x4.3-axle tractor: Mercedes-Benz Actros 3363, MAN TGX 26.540, SCANIA R620)1, 6x4 rear axle drive (with self-locking differential)- TAMIYA® 3-speed manual transmission (modular kit) with two CARSON rear axles (self-locking), drive shaft set 6x4.2, 6x6 all-wheel drive with 2+2 speed transmission (front axle/rear axle/transfer case self-locking)- CARSON 2-speed manual transmission Compact in conjunction with the CARSON 2-speed transfer case torque compensation (self-locking), driven front axle (self-locking), two rear axles (self-locking), drive shaft set 6x6.CARSON 2-speed transfer case (with speed compensation and self-locking longitudinal differential)The 2-speed transfer case is intended for use in TAMIYA 2- and 3-axle chassis in conjunction with the 2-speed Compact manual transmission. It offers you the possibility to convert your model to all-wheel drive or upgrade. It impresses with its simple installation, as existing holes/threads are used. The transfer case offers two additional switchable gears and a self-locking longitudinal differential that compensates for the speed difference between the front and rear axles and, in the event of a loss of traction, independently/automatically activates the differential lock and ensures 100% traction. Note: When using the 2-speed transfer case, the battery holder must be removed and the 7,2 V drive battery must be housed in the driver's cab. - Transfer case for driving one or more front and rear axles - 2 gears switchable (1st gear 1:3 / 2nd gear 1:1) - 7-way ball bearing - CNC machined aluminum housing - Hardened steel gears - 5 mm gear / output shaft - The gears are switched via a micro servo - Built-in longitudinal differential for speed compensation between the front and rear axles - Simple assembly by using existing holes (4 screws) on the TAMIYA ladder frame - Dimensions of distributor LxWxH: 32 x 62 x 40 mm - Weight approx.

Available immediately, delivery time: 1-4 days

Product number: 10033

€ 229,00 * € 250,00 * (8.4% saved)

Subscriptions

Motor flange with pinion for Mabuchi, Igarashi, TM72, TM120,

Motor flange with pinion for Mabuchi, Igarashi, TM72, TM120, Carson Poison Truck, Venom truck engine (251160).

Available immediately, delivery time: 1-4 days

Product number: 2491

€ 10,78 *

Subscriptions

Transfer cases for four-wheel, switchable with holder, 1x

Transfer case for all-wheel drive, switchable with holder, 1x input, 2x output, (251195) reduction ratio 2:1. Dimensions: 30x34x47 (WxLxH) without holder. All shaft inputs and outputs 5mm diameter with flattening. All shaft stubs 10mm long.

Available immediately, delivery time: 1-4 days

Product number: 7253

€ 108,89 * € 109,00 * (0.1% saved)

Subscriptions

Transmission mount for 3-speed transmission vertical installation

Transmission mount for 3-speed gearbox mounted vertically. With this holder the transmission is under (driven side). (251120). Hole spacing 30mm.

Available immediately, delivery time: 1-4 days

Product number: 1734

€ 8,22 *

Subscriptions

Transfer case for all-wheel drive, with holder self-locking, 1

Transfer case for all-wheel drive, with self-locking holder, 1x input, 2x output, reduction ratio 1:1. 8-way ball bearing. Dimensions: 54x30x57 (WxLxH). br>Transfer case, for scales 1:16 to 1:10, reduction ratio 1:1, permanent all-wheel drive, self-locking differential to compensate for the speed differences in the drive train, aluminum housing, 8-way ball bearing, input and output shafts 5mm with flattening, hardened gears, with retaining bracket (62mm wide), suitable for frame widths of 60-63mm. Dimensions: LxWxH: 54x30x57mm Contents: 1 transfer case, fastening screws, linkages

Available immediately, delivery time: 1-4 days

Product number: 10867

€ 144,13 * € 149,00 * (3.27% saved)

Subscriptions

3 manual gearbox without motor with transfer case

1x 3-speed manual gearbox without motor with transfer case and self-locking differential. Output shafts 5mm. Support brackets on the gearbox housing. Various motors can be used with different motor adapters (not included). (Not included in delivery).Reduction ratios:1st gear: 22,65:12nd gear: 11,32:13th gear: 5,66:1Gearbox housing made of aluminum, gears made of steel, hardened.10-fold ball bearings. Output shafts with a diameter of 5mm.The integrated self-locking differential compensates for speed differences. The gears are switched via a servo. The maximum permissible input speed is 6.500 rpm. The attachment to the frame is made using existing brackets on the gearbox housing. The frame width should be 60-63mm. Permanent all-wheel drive, self-locking differential to compensate for the speed differences in the drive train. Scope of delivery: 1 manual gearbox with distributor Fastening screws Linkage Dimensions: Length without motor: 80mm Width: 46,6mm Height: 64mm Suitable motor adapters: (not included) Article 1833, 2490, 2491, 1923, 2630, 8344.

Available immediately, delivery time: 1-4 days

Product number: 10860

€ 309,00 * € 317,90 * (2.8% saved)

Subscriptions

3-speed manual gearbox with WITHOUT distributor

3-speed manual transmission WITHOUT transfer case with 7,2V motor TM72. (251100) Output shaft 5mm. Incl. Motor adapter 251160. Reduction ratios: 1st gear: 22,65:12th gear: 11,32:13th gear: 5,66:1 SAVINGS PACKAGE: 3-speed manual transmission with 7,2V TM72 motor and motor adapter.

Ready to ship in 5 days, delivery time 1-4 days

Product number: 7923

€ 223,85 *

Subscriptions

1 motor flange with pinion for Faulhaber motors of series

1 motor flange with pinion for Faulhaber motors of the 2642xx/2657xx series. Suitable for the 3-speed gearbox from Veroma. Incl. 3 screws DIN912 M3x5mm. Adapter fits the Faulhaber motors with the article numbers 8327 and 8328. The pinion supplied fits as an input gear for the Veroma 3-speed manual gearbox (article no. 2489, 1832 and 10860).

Available immediately, delivery time: 1-4 days

Product number: 8344

€ 17,80 *

Subscriptions

Aluminium 2-speed manual matching Tamiya scale

1x aluminum 2-speed manual gearbox suitable for Tamiya scale. 500907265 The CARSON drive concept for TAMIYA trucks in 1:14 scale. Convert your TAMIYA 2- or 3-axle TAMIYA tractor into an all-rounder with our self-locking axles. The components can be easily replaced as they are attached to the existing mounting points. A huge advantage of these axles is that no additional space is needed for a switching servo (linkages and Bowden cables), as they lock independently/automatically in the event of a loss of traction. Officially licensed by ZF Friedrichshafen AG.You decide how you want to convert your 2- or 3-axle tractor, this is possible in two stages:Configuration options for:2-axle tractors:Mercedes-Benz Actros Gigaspace 1845, MAN TGX 18.540, SCANIA R470, VOLVO FH12, Mercedes-Benz 1838LS, Mercedes-Benz 18501, 4x2 rear axle drive (with self-locking differential)- TAMIYA® 3-speed manual transmission (modular kit) with a CARSON rear axle (self-locking)2, 4x4 all-wheel drive with 2+2 speed transmission (front axle/rear axle/transfer case self-locking)- CARSON 2-speed manual transmission Compact in conjunction with the CARSON 2-speed transfer case torque compensation (self-locking), driven front axle (self-locking), rear axle (self-locking), drive shaft set 4x4.3-axle tractor: Mercedes-Benz Actros 3363, MAN TGX 26.540, SCANIA R620)1, 6x4 rear axle drive (with self-locking differential)- TAMIYA® 3-speed manual transmission (modular system) with two CARSON rear axles (self-locking), drive shaft set 6x4.2, 6x6 all-wheel drive with 2+2 speed transmission (front axle / rear axle / transfer case self-locking)- CARSON 2-speed manual transmission Compact in conjunction with the CARSON 2-speed transfer case torque compensation (self-locking), driven front axle (self-locking), two rear axles (self-locking), drive shaft set 6x6. CARSON 2-speed gearbox Compact (without motor)This compact 2-speed gearbox is intended for use in TAMIYA 2- and 3-axle chassis in conjunction with the 2-speed transfer case. It offers you the possibility to convert your model to all-wheel drive or upgrade. It impresses with its simple installation, as existing holes/threads are used. The small design enables the installation of the driven front axle (500907267 - front axle installation kit 500907280 is required). - Compact 2-speed manual transmission - 2 gears: gear ratio 1:11,3 (1st gear) and 1:5,666 (2nd gear) - 5-fold ball bearings - CNC machined aluminum housing - Hardened steel gears - Incl. Aluminum engine mount for 540 engines (suitable for CARSON and TAMIYA standard and truck engines) - Incl. Motor pinion (3,17mm) and fastening material- Easy installation by using existing holes (2 screws) on the ladder frame- 5 mm gear/output shaft- The gears are switched via a micro servo- Dimensions of the gear (o. Motor) LxWxH: 47 x 62 x 35 mm- Weight (o. Engine) approx.

Ready to ship in 5 days, delivery time 1-4 days

Product number: 10040

€ 189,00 * € 200,00 * (5.5% saved)

Subscriptions

1x 3-speed manual transmission without engine with transfer case,

1x 3-speed manual gearbox without motor with transfer case, (251105). Output shafts 5mm. Various motors can be used using different flange adapters. (Not included in delivery).Reduction ratios:1st gear: 22,65:12nd gear: 11,32:13th gear: 5,66:1Gearbox housing made of aluminum, gears made of steel, hardened.8-fold ball bearings. Output shafts with a diameter of 5mm.The front axle can be switched on using a servo (not included). The gears are switched using a second servo. The maximum permissible input speed is 6.500 rpm.Suitable for scales 1:16 to 1:10.No gearbox holder is required for the current version.The attachment to the frame is done using the existing brackets on the gearbox housing. The frame width should be between 60-63mm. Scope of delivery: 1x manual transmission with distributor, fastening screws, linkages, dimensions: length: 80mm (without motor), width: 46,6mm (without support brackets), height: 64mm

Available immediately, delivery time: 1-4 days

Product number: 1832

€ 285,24 * € 299,00 * (4.6% saved)

Subscriptions

1x Cardan Shaft Set for Reduction Gearbox 4: 1

1x cardan shaft set for reduction gear 4:1. Article can be used in combination with article 9199 (gearbox), for example.Contents:1x long cardan shaft (75mm)1x short cardan shaft (23mm)2x cardan coupling for 5mm shaft with stud screw4 washers on the Gies branch (plastic)4 screws M3x25mmInstallation instructions

No longer available

Product number: 10795

€ 39,09 * € 40,99 * (4.64% saved)

Subscriptions

Details

3-speed manual gearbox with WITHOUT distributor

3-speed manual transmission WITHOUT transfer case with 12V motor TM120. (251100) Output shaft 5mm. Incl. motor adapter. (251160). Reduction ratios: 1st gear: 22,65:12th gear: 11,32:13th gear: 5,66:1 SAVINGS PACKAGE: 3-speed manual transmission with 12V TM120 motor and motor adapter.

Ready to ship in 5 days, delivery time 1-4 days

Product number: 7927

€ 215,32 *

Subscriptions

model building gearbox