Cookie Settings
This website uses cookies, which are necessary for the technical operation of the website and which are always set. Other cookies, which increase the comfort when using this website, are used for direct advertising or to simplify interaction with other websites and social networks, are only set with your consent.
Configuration
Technically required
These cookies are necessary for the basic functions of the shop.
"Reject all cookies" cookie
"Accept all cookies" cookie
Amazon Pay
Selected shop
CSRF token
Cookie Settings
Individual prices
Custom caching
PayPal payments
Session
Currency exchange
comfort functions
These cookies are used to make the shopping experience even more appealing, for example to recognize the visitor.
Wish list
Packstation / post office search (Bing Maps)
Statistics & tracking
End device detection
Affiliate
183,63 € * 184,89 € * (0,68% saved)
VAT included plus shipping and handling
Immediate dispatch, delivery time is about 1-4 days **
- Article no.: 11005
EasyBus light system semi-trailer KIEB 6 / 2 / 2 for Tamiya or Carson semi-trailer with Euro tail light .... More
Product information "EasyBus lighting system semi-trailer KIEB 6 / 2 / 2"
EasyBus lightbox semi-trailer KIEB 6 / 2 / 2 for Tamiya or Carson semi-trailer with Euro taillight.
Tips & Tricks for installation:
Tipp1: The KIEB 6 / 2 / 2 can be supplied with power in three variants: via the battery connector, via a servo connection and the BEC of a connected travel controller or via a bus output and the BEC of a connected KMB.
Tipp2: After switching on, the red LED of the KIEB 6 / 2 / 2 flashes twice. After that, the LED should go out as long as an IR connection is established. If the red LED flashes irregularly, the gain should be better adjusted with the potentiometer.
Tipp3: It is possible to check the transmission of the IR transmitter by pointing the transmitter diode at the camera of a mobile phone. If there is a purple flickering in the camera app, the diode sends.
Highlights & Details
Plug & Play solution (connect and drive)
One motor output for semi-trailer supports or spindle drives
Two freely adjustable servo outputs (eg for steerable trailing axle)
Receives ALL information ...
... all lighting functions and switching states ...
... but also all proportional functions ...
... up to 1.5m far or up to an angle of 90 °
Lighting boards can be connected directly via EasyBus
Technical data
Length (excl. Pin length) 60mm
Width 40mm
Height 12.5mm
Voltage 4-5 cells (max 8V)
BEC 5V (1A)
switching outputs Servo outputs 2
Motor outputs 2
EasyBus outputs 3
Bridgeable route up to 1.5m
Maximum angle approximately 90 °
What's in the box
KIEB 6 / 2 / 2
2x Euro rear light board
2x machined Euro housing
receiver diode
If the electronics are supplied by a rechargeable battery, we recommend (depending on the space available) these items:
Item 7110 with 4,8V Item 11121 with 4,8V Item 7823 with 4,8V Item 7745 with 4,8V Item 7549 with 6V Item 6457 with 6V
Tips & Tricks for installation:
Tipp1: The KIEB 6 / 2 / 2 can be supplied with power in three variants: via the battery connector, via a servo connection and the BEC of a connected travel controller or via a bus output and the BEC of a connected KMB.
Tipp2: After switching on, the red LED of the KIEB 6 / 2 / 2 flashes twice. After that, the LED should go out as long as an IR connection is established. If the red LED flashes irregularly, the gain should be better adjusted with the potentiometer.
Tipp3: It is possible to check the transmission of the IR transmitter by pointing the transmitter diode at the camera of a mobile phone. If there is a purple flickering in the camera app, the diode sends.
Highlights & Details
Technical data
What's in the box
If the electronics are supplied by a rechargeable battery, we recommend (depending on the space available) these items:
Related links to "EasyBus lighting system semi-trailer KIEB 6 / 2 / 2"
Available Downloads:
TIP!
1x spray primer 180ml, fine light gray.Good...
Contents 0.18 liters (€ 66,67 / 1 liter)
12,00 € * 14,78 € *
TIP!
TIP!
last seen