Volvo EC160E hydraulic excavator M1:14. All metal, finished model, color: yellow. By Fury Bear. Matches the Tamiya size. This Volvo hydraulic excavator model is a perfect replica of the Volvo EC160E. All 3 engine room doors can be opened and allow maintenance work to be carried out on the technical interior. The model is delivered as a finished model (ready-to-run) and can be put into operation immediately after unpacking. Headlights are mounted on the cabin roof, which also allow work in the dark or in poor visibility. A 2s battery (7,4V) is pre-installed. A FlySky remote control (10-channel) FSi63i is included. The model is fully functional, with exceptional performance and very high detail. The model is officially licensed by Volvo. Technical data: Weight: 10,8kg Scale: 1:14 Length: 61cm Width: 20cm Height: 21cm Length of the boom: 53,5cm Max. lifting weight of the boom: 10kg Max. lifting weight of the arm: 7kg Max. breaking force of the bucket: 10kg Max. speed: 600m/h Rotation speed of the upper carriage: 13 rpm. endlessly rotating boom, arm and bucket tines: aluminum sprockets: stainless steel, rustproof chains: aluminum hydraulic components: aluminum drive and rotation motor: 600KV brushless with 60A controller hydraulic motor (pump): 3300KV brushless with 30A controller oil tank: 50ml and oil pressure controller operating voltage: 7,4 - 11,1V remote control: FlySky FSi61i battery: 7,4V 7500mAh

Tamiya Mercedes Benz Arocs 3363 Red/Grey RTR ClassicSpace 6x4. 300023802 Ready to drive model. Painted in red/grey. With MFC-03 and 2,4GHz remote control. **Discontinued item. A real workhorse! The original 'Mercedes-Benz Arocs 3363 6X4 M-Cab Classic Space' was designed for the toughest use on construction sites. TAMIYA now presents this beautiful vehicle as a fully functional RC truck in 1:14 scale - already fully assembled, painted and with the MFC-03 unit! The unmistakable design of the new Arocs is as extraordinary as the truck as a whole. The look, which was specially developed for construction vehicles, includes a radiator grille with the so-called excavator tooth look, which is intended to convey the message: 'Bite through and grab hold'. To match the robust appearance, special protective grilles for the lighting system are attached to the bumper. With the 529 mm long and around 3 kg heavy model, impressive teams can be put together. The proven and robust TAMIYA truck technology can be found under the forward-tilting driver's cab. A powerful electric motor transfers its power to the two rear axles via a switchable 3-speed gearbox. A detailed aluminum ladder frame gives the model the necessary stability and flexibility. Thanks to its high deadweight and a fifth wheel plate, the Mercedes-Benz Arocs 3363 can be coupled with numerous TAMIYA and CARSON trailers. With the built-in multifunctional unit, almost all sound and light functions of the original can be simulated in a deceptively realistic way.Required accessories:Drive battery, charger, batteries for transmitterScope of delivery:Mercedes-Benz Arocs 3363 6x4, 2,4GHz remote control, MFC-03 unit (installed) WARNINGS:The instructions should be read and understood in full together with an adult. Keep away from small children. Children must not put any parts or packaging material in their mouths. The model may have some sharp corners. Be careful when handling it. Read the instructions included with the RC unit and keep them for future reference.If you have any difficulties during assembly, ask an adult to supervise the work or a model builder with RC experience or knowledge. Specialist dealer.Use tools only for their intended purpose. There is a risk of injury if used incorrectly.If you use paints and/or glue (not included in the kit), read and follow the instructions provided. Keep kit away from small children. Prevent children from putting any components in their mouths or pulling plastic bags over their heads.Technical details:- Fully assembled and adjusted truck, incl.

Carson rear tipper semi-trailer in Tamiya scale. 2-axle tipper. Tailgate with 2-hook lock. FINISHED MODEL. Max. load 10kg. Trough and rear wall made of hard PVC, milledAir spring dummies (coil springs)Aluminum chassis, milledball bearings4 trailer rims, wide4 wide tires7-chamber tail lights (with lighting boards)License plate plate (can be illuminated)Plastic mudguards with holdersRear flap lockAluminum underrun protection, milledTrailer supports, mechanically adjustablePlatform aluminum/plasticHydraulic cylinder dummyFINISHED MODEL. Built up and professionally painted.Spindle drive and trailer lighting set to match MFC-xx are assembled and ready for use.The tipping function/tilting spindle is operated via a 3-way switch. The vehicle frame is powder-coated (black) and the trough body is painted silver.

LiPo battery 7,4V/5000mAh. Hobbyline. With T-coupling, balancer connection. Dimensions: 130x38x19mm. Discharge rate: 50C.

Volvo FMX hydraulic tipper, truck 1:14. Ready-to-run model, made entirely of metal. All-wheel drive with good axle articulation and excellent off-road capability. The steering and drive are powered by electric motors, while the trough is operated hydraulically. The truck's hydraulic pump is a high-performance pump with an overflow valve and a flow rate of 400 ml/min. The pressure is adjustable and there is a 3-way switch valve as well as lockable differential axles and a reverse beeper. The truck also has a lighting system with which the headlights at the front and rear as well as the indicators right, left and reverse gear can be switched on. Thanks to its high ground clearance of 35 mm and high weight, the model feels at home on any surface. The powerful drive in conjunction with a multi-stage 2-speed gearbox provides enough power to easily master even the most difficult passages on loose ground. Overall, this 1:14 scale truck offers excellent value for money and is an ideal model for anyone looking for a robust and powerful functional model. Technical data: Dimensions: Length: 575mm Width: 180mm Height: 260mm Weight: 8kg Wheelbase: 285mm Ground clearance: 35mm Front wheels: 85mm Rear wheels: 85mm (both double tires) Rim diameter: 50mm Data: Number of channels: 12 channels Frequency: 2,4GHz Battery connector: T-Plug Battery: Li-Ion 7,4V 5.000mAh Flysky remote control of the latest generation already installed and set up! Plug-in charger and balancer tool set

1x Mercedes-Benz Actros 3363 Full Option built and painted in candy green. Includes MFC-03 and 4-channel system. RTR RTR model Mercedes-Benz Actros 3363 - fully built with sound, light and 4-channel remote controlTechnical details:-Length: 538mm-Width: 195mm-Height: 305 mm-Wheelbase: 237 + 103 mm-Driver's cab is painted in TS-52 (candy green) and already covered -Tamiya MFC-03 (drive controller, sound module, lighting system) is installed-LEDs are already pre-installed-3-speed gearbox enables authentic gear changes while driving-Metal leaf springs-Shock absorber-Fifth wheel plate can be operated automatically-4-channel remote control set is pre-installedRequired accessories:-Drive battery-Charger-Batteries for the transmitter

1x 1:14,5 O&K hydraulic excavator unpainted Detailed replica of the O&K RH25.5 crawler excavator. Made entirely of metal. Delivered assembled. RH 25.5 crawler excavator 1:14,5 assembled, unpainted - True-to-scale model of the 60 ton RH 25.5 crawler excavator in 1:14,5 scale. - The crawler excavator is highly detailed and the functions of the original have been implemented in a new level of sensitivity and performance. - The model is made entirely of metal, all steel parts used are made of corrosion-resistant stainless steel. - The 3-web chain links are milled from high-strength aluminum. - The hydraulic pump is driven by a high-quality, high-torque and continuous operation electric motor from Faulhaber. - The rotation of the upper carriage is realized by a gear motor and enables endless rotation. Optionally, the rotation of the upper carriage can also be achieved with a hydraulic motor. - Additional shovels and other accessories will also be available. The crawler excavator is delivered fully assembled, unpainted. Labeling is included. Scale: 1:14,5 Weight: approx. 15 kg Dimensions without boom: Length: approx. 430 mm Width: approx. 250 mm Height: approx. 260 mm Width of chain: approx. 52 mm Distance from housing to floor: approx. 107 mm Distance from chassis to floor: approx. 47 mm Length of chassis (chains): approx. 390 mm RC functions - Drive of crawler track - Rotating upper carriage - Boom - Stick (arm section at the front) - Shovel - Motor for hydraulic pump - Lighting (LEDs) - Hydraulic drive via two hydraulic motors with upstream planetary gear (since a hydraulic motor has low speeds, approx. 120 rpm, the drive is relatively slow). Faulhaber electric motor for hydraulic pump, mounted on rubber suspensions for particularly quiet operation, hydraulic oil tank made of metal. -Two chains consisting of 312 parts and chain tensioners -Each side has 8 rollers at the bottom and 3 rollers at the top -Large, high-quality, play-free narrow ring ball bearing for rotary drive -Various ball bearings -Four hydraulic cylinders with large piston diameter (inside 16 mm, outside 19 mm) -5 control valves, 1 pressure regulator, 1 I/O block -All hydraulic connections screwed -Interior of the driver's cab made of resin plastic -Transparent windows for the driver's cab -Electric drive with gearbox -Electric motor for continuous rotation of the upper carriage -Lighting units -Labeling set -53-page manual with exploded drawing The following is also required for operation: -Remote control (8-channel or higher) with receiver

1x 1:14,5 O&K hydraulic excavator painted. Detailed replica of the O&K RH25.5 crawler excavator. Made entirely of metal. Delivered assembled. RH 25.5 crawler excavator 1:14,5 assembled, painted - True-to-scale model of the 60 ton RH 25.5 crawler excavator in 1:14,5 scale. - The crawler excavator is highly detailed and the functions of the original have been implemented in a new level of sensitivity and performance. - The model is made entirely of metal, all steel parts used are made of corrosion-resistant stainless steel. - The 3-web chain links are milled from high-strength aluminum. - The hydraulic pump is driven by a high-quality, high-torque and continuous-operation electric motor from Faulhaber. - The rotation of the upper carriage is realized by a gear motor and enables endless rotation. Optionally, the rotation of the upper carriage can also be achieved with a hydraulic motor. - Additional shovels and other accessories will also be available. The crawler excavator is delivered fully assembled, painted and labelled. Scale: 1:14,5 Weight: approx. 15 kg Dimensions without boom: Length: approx. 430 mm Width: approx. 250 mm Height: approx. 260 mm Width of the chain: approx. 52 mm Distance from housing to floor: approx. 107 mm Distance from chassis to floor: approx. 47 mm Length of chassis (chains): approx. 390 mm RC functions - Drive of crawler track - Rotating upper carriage - Boom - Stick (arm section at the front) - Bucket - Motor for hydraulic pump - Lighting (LEDs) - Hydraulic drive via two hydraulic motors with a planetary gear connected upstream (since a hydraulic motor has low speeds, approx. 120 rpm, the drive is relatively slow). Faulhaber electric motor for hydraulic pump, mounted on rubber suspensions for particularly quiet operation, hydraulic oil tank made of metal. -Two chains consisting of 312 parts and chain tensioners -Each side has 8 rollers at the bottom and 3 rollers at the top -Large, high-quality, play-free narrow ring ball bearing for rotary drive -Various ball bearings -Four hydraulic cylinders with large piston diameter (inside 16 mm, outside 19 mm) -5 control valves, 1 pressure regulator, 1 I/O block -All hydraulic connections screwed -Interior of the driver's cab made of resin plastic -Transparent windows for the driver's cab -Electric drive with gearbox -Electric motor for continuous rotation of the upper carriage -Lighting units -Labeling set -53-page manual with exploded drawing The following is also required for operation: -Remote control (8-channel or higher) with receiver

1x 1:14 Scania R620 Red Full Option. - Ready to drive and painted model. Technical details: - Ready to drive, assembled and set up truck including 2.4GHz remote control, MFC-01 multifunctional unit and paintwork. - True to the original 2-axle drive - ABS injection-molded body - Driver's cab tiltable (forward) - Aerodynamic package - True to the original interior - Aluminum ladder frame with plastic reinforcements - Rear axle with metal bevel gears - Metal bevel gear differential - 3-speed manual transmission - Fifth wheel plate (suitable for all TAMIYA and CARSON trailers) - Leaf spring packages with spring struts on the front and rear axles - Aluminum front axle - Aluminum drive shafts - Electric motor type 540

1x 1:14 Scania R620 metallic orange. Full option. Technical details: - Ready-to-drive truck assembled and set up including 2.4GHz remote control, MFC-01 multifunctional unit and paintwork. - True-to-scale 2-axle drive - ABS injection-molded body - Driver's cab tiltable (forward) - Aerodynamic package - True-to-original interior - Aluminum ladder frame with plastic reinforcements - Rear axle with metal bevel gears - Metal bevel gear differential - 3-speed manual transmission - Fifth wheel plate (suitable for all TAMIYA and CARSON trailers) - Leaf spring packages with spring struts on the front and rear axles - Aluminum front axle - Aluminum drive shafts - Electric motor type 540

Iveco 4x4 hydraulic tipper, truck 1:14. Ready-to-run model, made entirely of metal. All-wheel drive with good axle articulation and excellent off-road capability. Truck in 1:14 scale Ready to Run.This fully equipped Iveco truck in 1:14 scale is ready for use.The truck is delivered complete, including electronics, servos, controller, remote control.The model has the true-to-original Iveco cab hood in 1:14 scale.The entire truck is made of high-quality metal and offers a robust construction.This high-quality hydraulic truck tipper leaves nothing to be desired. Thanks to its all-wheel function and excellent axle articulation, it is ideal for different terrain.The steering and drive are controlled by electric motors, while the hydraulic trough offers impressive functionality.The powerful hydraulic pump has an overflow valve and a flow of 400 ml/min. The pressure can be adjusted.In addition to the lockable differential axles, the two-speed gearshift, the realistic sound and light module and the reverse beeper, this model has a 4x4 all-wheel drive, which further improves its off-road capability.The integrated lighting system includes headlights at the front and rear as well as indicators and reverse gear lights.The Iveco truck is available in various attractive colors, including orange, red and white, just as shown in the pictures.Thanks to the generous ground clearance of 26 mm and the high weight, this model is at home on various surfaces. The powerful 540 high-torque brushed motor with 55T, combined with a multi-stage 2-speed gearbox, offers enough power to effortlessly handle even challenging passages on loose ground.In addition, the model is equipped with a realistic truck sound, which makes the driving experience even more authentic. Technical data:Length: 545mmWidth: 208mmHeight: 273mmWeight: 7,2kgWheelbase: 285mmGround clearance: 26mmFront wheels: 85mmRear wheels: 85mm (double tires)Rim diameter: 50mmNumber of channels: 14 channelsFrequency: 2,4GHzFlysky remote control of the latest generation already installed and set up.Required accessories: 2S LiPo battery with 5000-8000 mAh and charger.

Iveco 4x4 hydraulic tipper, truck 1:14. Ready-to-run model, made entirely of metal. All-wheel drive with good axle articulation and excellent off-road capability. Color: white Truck in 1:14 scale Ready to Run.This fully equipped Iveco truck in 1:14 scale is ready for use.The truck is delivered complete, including electronics, servos, controller, remote control.The model has the true-to-original Iveco cab hood in 1:14 scale.The entire truck is made of high-quality metal and offers a robust construction.This high-quality hydraulic truck tipper leaves nothing to be desired. Thanks to its all-wheel function and excellent axle articulation, it is ideal for different terrain.The steering and drive are controlled by electric motors, while the hydraulic trough offers impressive functionality.The powerful hydraulic pump has an overflow valve and a flow rate of 400 ml/min. The pressure can be adjusted.In addition to the lockable differential axles, the two-speed gearshift, the realistic sound and light module and the reverse beeper, this model has a 4x4 all-wheel drive, which further improves its off-road capability.The integrated lighting system includes headlights at the front and rear as well as indicators and reverse gear lights.The Iveco truck is available in various attractive colors, including orange, red and white, just as shown in the pictures.Thanks to the generous ground clearance of 26 mm and the high weight, this model is at home on various surfaces. The powerful 540 high-torque brushed motor with 55T, combined with a multi-stage 2-speed gearbox, offers enough power to effortlessly handle even challenging passages on loose ground.In addition, the model is equipped with a realistic truck sound, which makes the driving experience even more authentic. Technical data:Length: 545mmWidth: 208mmHeight: 273mmWeight: 7,2kgWheelbase: 285mmGround clearance: 26mmFront wheels: 85mmRear wheels: 85mm (double tires)Rim diameter: 50mmNumber of channels: 14 channelsFrequency: 2,4GHzThe latest generation of Flysky remote control is already installed and set up.Required accessories: 2S LiPo battery with 5000-8000 mAh and charger.

1:14 8x8 heavy-duty truck for Mercedes Arocs/Actros ARTR. Fully assembled 8x8 chassis with heavy-duty tower, motor and servos. Suitable for the TAMIYA Actros or Arocs driver's cab. Except for the fenders, everything is CNC-made from solid metal. The details, such as the true-to-original Mercedes exhaust or the urea tank, are a particular highlight. Thanks to the standard all-wheel drive with switchable differential lock, this truck can pull even the heaviest construction machine to the construction site and back again. To operate it, you only need a driver's cab, a 7,4V battery and a suitable remote control and you're ready to go. The drive battery also fits in the heavy-duty tower. Dimensions: Length: 562mm, width: 185mm, saddle height: 95mm, distance between 1st and 2nd axle: 195mm

Backhoe loader BL71, 1:14, ARTR. Assembled, painted in yellow/gray. Without RC. Backhoe loader BL71, 1:14, ARTR. Assembled, painted in yellow/gray. Without RC. The new BL71 backhoe loader is a technical masterpiece from LESU! The basic tractor with all-wheel drive is already a highlight in 1:14 scale, but a tractor with a front loader and rear excavator has never been produced in series before! The hydraulic front loader features a folding bucket and a foldable pallet fork. The excavator at the rear, in addition to stable support, has a swivel radius of 180°, allowing it to reach every corner. The entire excavator arm can move back and forth via a precise liner slide with a spindle at the rear! The absolute eye-catcher, however, is the swiveling driver's seat! Just like in the original, the driver can swivel from the front to the rear. The steering is hydraulic. The backhoe loader is made entirely of metal and comes fully assembled and painted with sound, lights, and hydraulics. You only need a 17-channel remote control, battery, and hydraulic oil. The following functions are available: Driving, hydraulic steering, differential lock, front loader lift, front loader bucket tilt, front loader bucket open, hydraulic switching from front loader to excavator, support, excavator arm 1, excavator arm 2, excavator bucket, excavator arm swivel, excavator linear movement, driver's seat rotation, light, indicators, engine sound, horn, rotating light with 7 functions. On request, we also offer the backhoe loader fully ready to drive with the new Paladain PL18EV 4D remote control. Dimensions: Length: 513 mm, Width: 196 mm, Height: 283 mm, length of excavator: 477 mm, height of excavator: 416mm Height of lower edge of bucket: 255mm Weight: approx. 7600g Hydraulics: Pressure: 0-30 bar adjustable Operating voltage: 7,4V Scope of delivery: Backhoe loader fully assembled and painted in yellow/grey, hydraulic system, sound module and lighting system with LEDs. Also required for operation: Hydraulic oil, 7,4V battery, remote control with at least 17 channels and receiver. Delivery can only be made on a Euro pallet with a freight forwarder for 129 euros within Germany. International shipping only on request! Alternatively, collection from our store is possible.

Telescopic mini wheel loader MLC-8. Assembled, painted yellow/gray. With RC. RTR model. Telescopic mini wheel loader MLC-8. Assembled, painted yellow/gray. With RC. RTR model. Small, compact metal telescopic wheel loader with hydraulics, lights and sounds, and a fork bucket. The mini wheel loader is highly maneuverable and has a mechanical quick coupler for various tools. The hydraulic connections are conveniently located on the side of the front arm. All-wheel drive and differential lock are included. With the practical telescopic arm, even tall vehicles can be loaded easily. A height of 361 mm can be reached! Scope of delivery: Model fully assembled and painted with FlySky ST8 remote control including hydraulic cylinders, brushless pump, servos, and drive motor with controller, lights and sounds, and a fork bucket. Dimensions: Length: 478 mm Width: 164 mm Height: 221 mm Height of bucket bottom edge: 361 mm Steering angle: 47° Weight: 3800 g A 7,4 V (2s) battery pack with a T-connector is also required for operation.

Tractor 4x4, 1:16. Fully assembled with body, light and RC. Complete finished model with metal chassis with all-wheel drive, plastic tractor body from Bruder, lighting, sound and remote control. Chassis painted in grey and rims in red. The rear power lift is moved via a spindle drive. All servos for steering and differential lock are already installed. A speed controller is also available. LED lighting and sound are also installed. All you need is a drive battery and a charger. Dimensions: Length: 420mm Width: 218mm Height: 225mm Weight: 4,8kg Operating voltage: 7,4V-11,1V Scope of delivery: Chassis fully assembled and painted Bruder body with LEDs Servos, controller, LED, sound and RC Required for operation: 7,4V-11,1V battery and 4x AA batteries for the transmitter