RC articles

Filter
1x Memory switch PS4a with 4x 4A output 4x
1x memory switch PS4a with 4x 4A output 4x on/off function on 1 RC channel max. voltage 20V. 13x15x2,5mm, CTI product switching module (4x memory) with 4 separately switchable outputs. Each output can be switched on or off separately. From the middle position of a transmitter, outputs 1 and 2 react in one direction (more than 1,5ms) and outputs 3 and 4 in the other direction (less than 1,5ms). Each output can be loaded with max. 4A, whereby the sum of all load currents should not exceed 6A. Ideal switching module for switching 4 different light functions, for example.

Available immediately, delivery time: 1-4 days

Product number: 3022

€ 18,00 *
1x Fahrregler THOR 4 until 15V max. 4A 100% forward, 100%
1x THOR 4 speed controller, up to 15V max. 4A 100% forward, 100% reverse. With BEC 1000mA. 15x12x4,5mm, CTI product. Micro forward-reverse controller for 5-10 cells and 4 amps continuous output Low-drop voltage regulator. Not suitable for brushless motors! The controller is particularly suitable for small slow-running motors in mini and micro models. But also ideal for RB35 motors. Dimensions: width: 15mm, depth: 12mm, height: 4mm Weight with cables: 6 grams Continuous current: 4 amps, short-term: 12 amps BEC: 1000 mA (up to 8 cells) RDSon: 0,09 ohms Servo cable/connector: Graupner/JR Detailed instructions are included.

Available immediately, delivery time: 1-4 days

Product number: 3020

€ 18,00 *
1 15 Fahrregler THOR Li until 16V max.16A 100% forward
1 speed controller THOR 15 Li, up to 16V max.16A 100% forward, 100% reverse. With BEC 1000mA. 24x20x7mm, CTI product. With LiPo monitoring. Forward/reverse controller for 2-3 LiPo cells for scale models with Bühler motors and standard motors up to size 540.Width: 24mm, depth: 20mm, height: 6mmWeight with cables: 14gContinuous current: 16 ampsShort-term: 50 ampsRDSon: 0,015 OhmBEC: 5 Volt 1000mAh servo cable/plug: Graupner/JR Detailed instructions are included. Undervoltage detection and reduction When switched on, the THOR15Li detects whether a 2-cell or 3-cell LiPo battery is connected. Accordingly, the reduction limit is set to either 6 volts or 9 Volt is set. If the battery voltage falls below this limit then only 1/4 of the target speed is passed on to the motor. So a significant reduction in the ride that everyone will notice and can drive "home" with this reduced ride. Not for brushless motors. Motors suitable!

Available immediately, delivery time: 1-4 days

Product number: 5473

€ 21,00 *
1x speed controller THOR 4s, up to 15V max. 4A 100% forward,
1x speed controller THOR 4s, up to 15V max. 4A 100% forward, 100% reverse. Self-learning. With BEC 1000mA. 15x12x4,5mm, CTI product. Self-learning means:When switched on, the controller recognizes the current control position in the transmitter and assumes this position as the current ZERO POSITION!Micro forward-backward controllerfor 5-10 cells and 4 amps continuous outputLow-drop voltage regulator.Not suitable for brushless motors!The controller is particularly suitable for small slow-running motors in mini and micro models.But also ideal for RB35 motors.Dimensions: width: 15mm, depth: 12mm, height: 4mmWeight with cables: 6 gramsContinuous current: 4 amps, short-term: 12 ampsBEC: 1000 mA (up to 8 cells)RDSon: 0,09 ohmServo cable/connector: Graupner/JRDetailed instructions are included.

Available immediately, delivery time: 1-4 days

Product number: 3087

€ 18,00 *
Throttle controller THOR 15 HCs, up to 16V max.16A
1x THOR 15 HCs speed controller, up to 16V max. 16A, self-learning, 100% forward, 100% reverse. With BEC 1000mA. 24x20x7mm, CTI product. Self-learning means: When switched on, the controller recognizes the position of the encoder in the transmitter and takes this as the current zero position! Not suitable for brushless motors!

Available immediately, delivery time: 1-4 days

Product number: 3049

€ 21,00 *
Tip
1x Servonaut S22 speed controller for model trucks and
1x Servonaut S22 speed controller for trucks and functional models/vehicles. Speed ​​controller for 7,2 to 12V and 20A/5min at 16 kHz clock frequency. BEC 5V/3A. 2 switching outputs, 700mA each for brake light and reversing light, control output for Servonaut sound modules, including instructions, dimensions approx. 70x38x9mm. For functional models of size 1:16 to 1:8. Further development of the well-known S20 controller! Better resolution and sensitivity: 450 speed levels! The inertia of a heavy vehicle is realistically reproduced. Integrated protective functions: - Overload protection - Overtemperature protection - Undervoltage protection Also suitable for bell-shaped armature motors! Seamless EMF braking, no loss of control when driving downhill. Delay-free change forward/backward. Powerful 5V/3A receiver supply with large cooling surface. Diagnostic LEDs.Undervoltage shutdown for 6 or 10 cells NiMH and 2 or 3 cells LiPo.Automatic zero setting with start-up protection.Instructions for this article are available for download. Downloading is free! (except for your online costs).NEW article - follow-up article to the S20!

Available immediately, delivery time: 1-4 days

Product number: 9182

€ 104,99 *
%
Tip
1x racing battery pack with 5000er-SUB-C cells, cells 7,2V.6
1x racing battery pack with SUB-C cells, 7,2V 6 cells, 5000mAh with Tamiya plug. SUB-C cells. Dimensions approx. 137x47x25mm. Approx. 430 g, NiMH, R3x2 design. With silicone wires! This battery pack fits in the standard battery compartment of all Tamiya tractors! 5000mAh - for extremely long driving fun!!! The matching charging cable can be found under item number 1867 - here in the shop.

Available immediately, delivery time: 1-4 days

Product number: 9680

€ 42,99 * € 44,90 * (4.25% saved)
1x speed controller THOR14LF, up to 20V max. 14A 100% forward, 100%
1x THOR14LF speed controller, up to 20V max. 14A 100% forward, 100% reverse. Without BEC system! 23x15x7mm, CTI product. This item replaces the previous THOR 14 (6866)! This controller has NO BEC system. It is therefore ideal as a "secondary" controller for pumps or other drives. Also ideal for ramp and support drives. It must be supplied by the receiver. The BEC voltage must be between 5 and 5,5 volts DC. Not suitable for brushless motors! Technical data: Maximum voltage: 20 volts. RDSON is 25 milliohms. Maximum current: 14 amps. 1qmm silicone cables are attached for battery and motor connection. Dimensions: 23x15x7 mm

Available immediately, delivery time: 1-4 days

Product number: 11689

€ 18,00 *
%
SFR-1 sound drive controller from BEIER. Especially for trucks
1x SFR-1 sound speed controller from BEIER. Specially developed for trucks. 16 switching outputs for lighting. Can be set using the Sound Teacher SFR software. WITH CD-ROM/DVD or USB stick Speed ​​controller for DC brush motor, sound module and light control module in one! Also suitable for bell-armature motors! Specially developed for trucks. Powerful BEC with 5,6V 3A. Optional load control, cruise control and brake function. Can be set in great detail using the -Sound Teacher SFR-. The speed controller is characterized by its high sensitivity. The controls are very realistic and dynamic and guarantee absolute driving fun. Thanks to a wide range of setting options, the speed controller can be easily and individually adapted to the most diverse model requirements and driving characteristics. All settings are made using the -Sound Teacher SFR- - the convenient configuration program from BEIER-Electronic. The model's lighting can be connected directly to the speed controller using the 16 light outputs. The speed controller has an extra output for connecting the IR transmitter diode for the light module SM-IR-16-2. (Article 9810). Features: - Supply voltage: 6-18V - Max. Motor current 30 A (continuous) 60 A (short-term) - PWM clock frequency 20 or 40 kHz - 16 switching outputs for the lighting - Powerful BEC 5,6 V 3 A - 6 proportional inputs (throttle, steering, control, sound, light) - 2 proportional outputs (servo outputs) - Failsafe in the event of reception interference (engine stop) - Start-up protection when switched on - Battery voltage monitoring - Temperature monitoring - Short-circuit protection for motor output stage - Short-circuit protection for BEC - Short-circuit protection switching outputs Can be selected via Sound Teacher SFR: - Load control on/off - Cruise control on/off - Braking function on/off - Handbrake function on/off - Selection of battery type: LiPo/ other type - Learning function (setup) for throttle channel on/off Can be set via Sound Teacher SFR (K-USB-2 required!):-Firmware update-Diagnosis-Channel inversion-Shutdown of undervoltage monitoring-Reduction of reversing speed-Selection of PWM clock frequency-Activation/setting of mass inertia-Activation/setting of steering inertia-Setting of handbrake hardness-Setting of throttle curve-Configuration of switching outputs (output type, brightness, xenon)-Configuration of light switch-Configuration of control channelThe speed controller is delivered with a standard configuration and is ready for use!-Battery connection 2x 1,5qmm, 25cm long, DEANS T-plug-Motor connection 2x 1,5qmm, 25cm long-2x servo cable for connection to receiver, 30cm long-Connection cable for loudspeaker, 25cm long-Cable for standby switch or volume potentiometer, 25cm-1x ribbon cable 40cm for connecting the switching outputs-Micro SD card (4GB) plus adapter-DVD with Sound-Teacher SFR-1 or USB stick (from 8/2024)-Manual SFR-1technical data:-Dimensions: 80 x 47 x 23 mm-Weight: 86g

Available immediately, delivery time: 1-4 days

Product number: 10974

€ 254,99 * € 264,95 * (3.76% saved)
Servo patch cable 10cm
1x servo patch cable 10cm. Both sides JR connector. 0,14qmm. BEIER-Electronic Accessories.

Available immediately, delivery time: 1-4 days

Product number: 9811

€ 2,84 *
1 15 Fahrregler THOR HC until 15V max.18A 100% forward
1 speed controller THOR 15 HC, up to 15V max.18A 100% forward, 100% reverse. With BEC 1000mA. 24x20x7mm, CTI product. Not suitable for brushless motors!

Available immediately, delivery time: 1-4 days

Product number: 3019

€ 21,00 *
Speakers 4 Ohm 50x50x22 mm
1x speaker 4 Ohm 50x50x25 mm. 88gr. Suitable for USM-RC-2, 10 watts, music output. Small design. LS-4R-10W-50 A suitable speaker housing: Article 9848 (not included).

Available immediately, delivery time: 1-4 days

Product number: 9847

€ 15,95 *
Switching module for braking and reversing light 2 outputs with max
Switching module for brake and reversing light 2 outputs with max. 4 A, for parallel connection to a speed controller. PS2BR, 13x15x2,5mm, CTI product.

Available immediately, delivery time: 1-4 days

Product number: 3021

€ 18,00 *
Connection terminal AKL-8 BEIER-Electronic. Simple wire
Connection terminal for switching outputs For easy wiring of BEIER UFR-1230, SFR-1, UFR-1230D. AKL-8. Scope of delivery:10-pin connection terminal with spring contacts10-pin flat edge cable, color-coded, approx. 20cm long, with post couplings on both sidesOperating instructions

Available immediately, delivery time: 1-4 days

Product number: 10986

€ 13,95 *
1 spring steel clevis V, 3,0mm thread
1 spring steel clevis V, 3,0mm thread.

Available immediately, delivery time: 1-4 days

Product number: 1520

€ 0,82 *
1x Servonaut MF8 mini-speed controller for adjusting and
1x Servonaut MF8 mini speed controller for actuators and auxiliary drives. WITHOUT BEC! Load capacity up to 8A. Frequency 4kHz. Voltage 6-12V (5-10 NiMH cells). Dimensions: 50x19x7mm. Integrated protection functions: -Overload protection -Overtemperature protection -Undervoltage protection -Automatic zero setting, no start-up protection For drive systems, the S10 or S22 controllers are recommended. These controllers have BEC and connections for brake and tail lights. Instructions are available for downloading this article. Downloading is free! (except for your online costs). NEW ITEM - replaces the previous MFR!

Available immediately, delivery time: 1-4 days

Product number: 9191

€ 33,59 *
1x relay pole reversal switch with end position switch-off. Failsa
1x relay reversing switch with end position shutdown. Failsafe function. For motor polarity reversal with end position detection. Switching capacity max. 10A, 1-40V. Features: - programmable switch-on point - connections for two end position switches, module stops the motor as soon as the end position is reached - negligible power consumption - possible switching capacity per switch 10 A / 1-40 Volt - screw connections - failsafe - dimensions 43 x 34 x 21 mm - weight 40 g with Graupner servo cable When connected to a free channel on the joystick, the connected motor is in the middle position. Can of course be operated with a free channel on the joystick or an ON/OFF/ON switch on the transmitter. Lever up: the motor turns in one direction Lever down: the motor turns in the other direction Lever in the middle position: the motor stands still. There is a practical holder for this module: item 11956.

Available immediately, delivery time: 1-4 days

Product number: 9856

€ 22,94 *
1 15 throttle THOR HF until 16V max.16A, with brake
1 speed controller THOR 15 HF, up to 16V max.16A 100% forward, 100% reverse. 18kHz. With BEC 1000mA. With braking function. 24x20x6mm, CTI product. Special feature of the HF controller: Clocking at 18kHz, which enables sensitive control and the whistling in the motor is no longer audible. A self-learning LiPo undervoltage detection reduces the motor speed at 9 or 6 volts. Voltage: up to 16 volts Current: up to 16 amps Undervoltage detection with reduction High-frequency clocking 18KHz (no motor whistling) BEC: 1 amps Dimensions: 24x20x6 mm Not suitable for brushless motors! For the first time, these THOR controllers are equipped with a brake so that a The vehicle does not roll downhill uncontrollably on a slope. Another special feature is the high clock speed of 18KHz. This achieves more sensitive control and the whistling in the motor is no longer audible. A self-learning LiPo undervoltage detection reduces the motor speed at 9 volts or 6 volts. The integrated BEC supply can be used to supply the receiver and a small servo. This BEC voltage is short-circuit-proof and temperature-protected. But be careful: This means that if the temperature is too high, this voltage switches off and the receiver would therefore be temporarily without power! So, carry out extensive tests or use an external BEC, e.g. an X-BEC. When switched on, the THOR15HF detects whether a 2-cell or 3-cell LiPo battery is connected. Accordingly, the cut-off limit is set to either 6 volts or 9 volts. If the battery voltage falls below this limit, only 1/4 of the target speed is passed on to the motor, i.e. a significant reduction in the speed that everyone will notice and can drive "home" with this reduced speed. Of course, the controller can also do the same NiMh or lead batteries can be operated.Control range: the zero point is fixed at 1,5ms pulse width and therefore corresponds exactly to today's common RC systems.Before and after, i.e. stick forward/back, the motor rotates continuously forwards/backwards, in each case up to to the maximum speed. Attention: the range of the RC system should be checked before the first trip. If the controller is defective, it can happen that the motor starts even when the receiver is switched off!

Available immediately, delivery time: 1-4 days

Product number: 9764

€ 26,00 *
1x page correct chain mixer
1x side-correct chain mixer. This mixer allows you to control any tracked vehicle with 2 forward/backward controllers using a joystick. In contrast to the simple V-mixer, this mixer controls both drive motors in a side-correct manner. It therefore allows you to control any tracked vehicle with two forward/backward controllers using a simple joystick. This mixer is also ideal for operating boats with multiple screw drives. Whether you have 2 or more screws, this mixer allows you to perform turning maneuvers much more tightly and precisely. Suitable for both forward/backward and pure forward drives. Features: 2x receiver input (throttle & steering) and 2x output to the controller (motor left & motor right) programmable zero point programmable mixing of 20-100% 2 modes selectable: side-correct and V-mixer Dimensions 34x34x5 mm Weight 15g with cables

Available immediately, delivery time: 1-4 days

Product number: 9776

€ 23,95 *
1 Truck sound module SM3 with speed and
1 truck sound module SM3 with engine noise depending on speed and driving situation. Compressed air noise, horn, starting, stopping. 7,2-12V 3 watts at 8 ohms. A free receiving channel required! Successor sound module to the previous SMT. Half the size of the predecessor, space-saving installation. 5 engine types selectable! Previous engine types of the SMT and SMX! Reverse warning tone, adjustable idle and full throttle speed. 5 setups for US or European trucks. Mini volume control for hidden installation on the model. Starter and horn are operated using the joystick or button/switch with 3 positions on the transmitter.Wavetable sound synthesis.Can be combined with many speed controllers from other manufacturers (forward-backward controller without braking range).Power is supplied from the drive battery.With battery connector (BEC).Optional sound controller SM-EQ available as an accessory.Dimensions approx. 55x28x13mm.Instructions are available for downloading this article. Downloading is free! (except for your online costs).Recommended loudspeakers with 7,2V supply voltage:Article with 8 ohms: 7028, 9851, 9852, 9854.Recommended loudspeakers with 12V supply voltage:Article 8962.

Available immediately, delivery time: 1-4 days

Product number: 8961

€ 147,99 *
Data Cable K-USB 2
1x data cable K-USB-2. For live diagnosis, transfer of sound projects. Connection via USB interface. The data cable is NOT required. With the data cable K-USB-2, the sound modules SFR-1, SFR-1-D, USM-HL-2, light modules LM-xx, USM-RC-2 and USM-RC-3 as well as the speed controllers UFR-1230 /UFR-1230-D can be connected to a PC via a USB interface.The data cable has two functions:1. Live diagnosisWith the help of the data cable, the sound teacher can receive and display the current diagnostic data live (e.g. position of the proportional channels, status of the inputs and outputs, nautic values, etc.). This option is very helpful when troubleshooting.Note:The sound modules SFR-xx, USM-HL-2 and USM-RC-x can also save the diagnostic data on the SD card. This recorded data can be viewed without a data cable using the Sound Teacher's diagnostic function. However, the saved values ​​have the disadvantage that you only see the "past" and not what is currently happening (live) on the module. 2. Transferring the configurations and sounds from the Sound Teacher/Drive Teacher to the SFR-x, USM-HL-2, USM-RC-x and UFR-1230/UFR-1230-D modules If a sound or a setting in the configuration is to be changed, the SD card must normally be unplugged from the module, plugged into the PC's card reader, the project data saved to the SD card using the Sound Teacher and the card plugged back into the sound module. However, if changes are made frequently, which occur particularly when the device is first put into operation or when testing new functions, unplugging and plugging can quickly become annoying. Using the data cable, all changes can be easily transferred to the sound module without having to keep re-plugging the SD card. However, transferring sounds using the data cable is relatively slow! A sound that is 10 seconds long takes around 60 seconds to transfer using the data cable. Therefore, transferring long sounds or large, new projects using the data cable is only advisable to a limited extent. The data cable is not absolutely necessary for setting up the sound module, but is often very helpful if you want to work a lot with the various setting options of the sound module.

Available immediately, delivery time: 1-4 days

Product number: 9822

€ 23,95 *
1x limit switch module-2 2 with limit switch inputs. For
1x limit switch module 2 with 2 limit switch inputs. For plugging into the controller control cable. 20x8x3mm, CTI product. ESM-2

Available immediately, delivery time: 1-4 days

Product number: 7722

€ 17,99 *
Servo controller travel tip delay. Moves a servo with it
Servo controller travel-tip-delay. Moves a servo with adjustable speed and adjustable servo travel. CTI product. This servo controller is a true all-round talent! The 2 adjustment potentiometers allow the speed of the servo movement (delay) to be adjusted, as well as the reduction of the servo travel. The servo controller travel-tip-delay can be operated directly on the receiver output or via a PS4x module!

Available immediately, delivery time: 1-4 days

Product number: 6057

€ 18,00 *
%
1 Servo HS-645MG (Hitec). Powerful standard servo. Dimensions:
1 servo HS-645MG (Hitec). Powerful standard servo. Dimensions: 40x20x37mm. 55gr. Metal gear. 2 ball bearings. 77/96Ncm. 0,24s/60°. Uni/JR connector. Powerful standard servo. Ideal as a steering servo. Scope of delivery: 1 servo 5 control discs/levers Fastening material Gearing: 24T Ball bearing: yes Waterproof: no Torque at 4,8V: 8kgcm Torque at 6,0V: 10kgcm Gear: metal Motor type: brushed Electronic type: analog

Available immediately, delivery time: 1-4 days

Product number: 7968

€ 40,50 * € 41,10 * (1.46% saved)
%
SFR-1 sound drive controller from BEIER. Especially for trucks
SFR-1 Sound Speed ​​Controller from BEIER. Specially developed for trucks. 16 switching outputs for lighting. Can be adjusted using the Sound-Teacher SFR software. No CD-ROM/DVD/USB stick required. Speed ​​controller for DC brushed motors, sound module, and light control module in one! Also suitable for coreless motors! Specially developed for trucks. Powerful BEC with 5,6V 3A. Optional load control, cruise control, and braking functions. Can be adjusted in great detail using the Sound Teacher SFR. The speed controller is characterized by its high sensitivity. The control is very realistic and dynamic, guaranteeing absolute driving pleasure. Thanks to its diverse setting options, the speed controller can be easily and individually adapted to the most diverse model requirements and driving characteristics. All settings are made using the Sound-Teacher SFR – the convenient configuration program from BEIER Electronic. The model's lighting can be connected directly to the speed controller via the 16 light outputs. The speed controller has an extra output for connecting the IR transmitter diode for the SM-IR-16-2 light module (item 9810). Features: - Supply voltage: 6-18V - Max. Motor current 30 A (continuous) 60 A (short-term) - PWM clock frequency 20 or 40 kHz - 16 switching outputs for the lighting - Powerful BEC 5,6 V 3 A - 6 proportional inputs (throttle, steering, control, sound, light) - 2 proportional outputs (servo outputs) - Failsafe in case of reception interference (motor stop) - Start-up protection when switched on - Battery voltage monitoring - Temperature monitoring - Short-circuit protection for the motor output stage - Short-circuit protection for the BEC - Short-circuit protection for switching outputs. Selectable via Sound Teacher SFR: - Load control on/off - Cruise control on/off - Brake function on/off - Handbrake function on/off - Selection of battery type: LiPo/other type - Learning function (setup) for the throttle channel on/off. Adjustable via Sound Teacher SFR (K-USB-2) required!): -Firmware update -Diagnosis -Channel inversion -Shutdown of undervoltage monitoring -Reverse speed reduction -Selection of PWM clock frequency -Activation/adjustment of mass inertia -Activation/adjustment of steering inertia -Adjustment of handbrake hardness -Adjustment of throttle curve -Configuration of the switching outputs (output type, brightness, xenon) -Configuration of the light switch -Configuration of the control channel The speed controller is delivered with a standard configuration and is ready for use! -Battery connection 2x 1,5 mm², 25 cm long, DEANS T-connector -Motor connection 2x 1,5 mm², 25 cm long -2x servo cables for connection to receiver, 30 cm long -Connection cable for loudspeaker, 25 cm long -Cable for standby switch or volume potentiometer, 25 cm -1x ribbon cable 40 cm for connecting the switching outputs -Micro SD card (4 GB) plus adapter Data:-Dimensions: 80 x 47 x 23 mm-Weight: 86g

Available immediately, delivery time: 1-4 days

Product number: 10977

€ 249,00 * € 254,95 * (2.33% saved)
1x speed controller THOR14LFs, up to 20V max. 14A 100% forward, 100%
1x THOR14LFs speed controller, up to 20V max. 14A 100% forward, 100% reverse. Without BEC system! SELF-LEARNING. 23x15x7mm, CTI product. Successor to the THOR14s (6867)!Self-learning means:When switched on, the controller recognizes the current position of the encoder in the transmitter and takes this as the current zero position!This controller must be supplied with power from the receiver as it does NOT have a BEC system!Not suitable for brushless motors!Technical data:Maximum voltage: 20 volts.RDSON is 25 milliohms.Maximum current: 14 amps.1qmm silicone cables are attached for battery and motor connection.Dimensions: 23x15x7 mm

Available immediately, delivery time: 1-4 days

Product number: 11939

€ 18,00 *
Memory switch PS4b with 4x 4A output 4x on / off function
Memory switch PS4b with 4x 4A output 4x on / off function on 1 RC-channel outputs as 2 Blinker.Max. Voltage 20V 13x15x2,5mm, CTI product

Available immediately, delivery time: 1-4 days

Product number: 3023

€ 18,00 *
%
1 ball head 5x3mm, total length 12mm, brass. M3 thread
1 ball head 5x3mm, total length 12mm, brass. M3 thread, thread length 5mm. Suitable for 5mm open ball sockets.

Available immediately, delivery time: 1-4 days

Product number: 8095

€ 0,79 * € 5,89 * (86.59% saved)
1x throttle AS-12 / 35RW Truck EVO III. 100% pre / rev
1x speed controller AS-12/35RW Truck EVO III. 100% forward, 100% reverse. Max. 35A. With BEC max. 3A / short 5A. 18kHz clock speed! 6-18V input voltage. 5-14 cells NiMH or 2-4 LiPos. Dimensions: 36x33x11mm. 33gr. Version without cruise control! Max. current: 35A (50A short). Autosetup, failsafe, LED monitor, LiPo detection, undervoltage protection, intelligent soft polarity reversal, 2 different handbrake modes. Overtemperature shutdown. Outputs for brake and reversing light with 1A each. Handbrake The AS12-35RW Truck Evo III has two different handbrake modes. In normal mode (green LED flashes) the brake slowly switches on in the zero position and ensures that the model stops but does not. This mode is recommended for most applications, especially for street trucks. For crawlers and four-wheel drive trucks that like to stop on a slope, it is recommended to select the brake mode (red LED flashes). In this mode, the brakes are applied very quickly and thus prevent the model from rolling away on the slope. But be careful: This mode can brake a model at full speed very quickly! Performance features: - 5-14 cells / 2-4 Lipos / 12 Volt lead (with Lipo monitoring 3,4V per cell) - Automatic cell count detection in Lipo mode (at approx. 3,4 volts per cell), the maximum power is limited to 25% and the controller signals that the battery is empty by jerking the motor) - 35 A continuous, 50 A short-term - Switching BEC up to 14 cells / 4s Lipo. 3A continuous up to 5A short-term - two different braking modes can be programmed (street truck / crawler). - Lipo monitoring can be switched on / off - Overtemperature shutdown, if the controller gets too hot it regulates back to max. 25% power. - Full HF 18 kHz output stage over the entire control range. NO motor whistling and extremely sensitive control. - Motor-friendly polarity reversal through speed-dependent polarity reversal time with brake. The braking time is calculated using an algorithm. (In the lower speed range the polarity is reversed immediately; at high speeds the controller brakes the motor gently so that the batteries and motor are protected from high current peaks.) - Handbrake function. When the throttle is at 0, the vehicle is first braked gently, then the handbrake is pulled.- Perfect failsafe (receiver signal is constantly checked) LED shows when the reception signal is lost.- Motor beep acknowledgement (for programming and for the OK message when connecting the battery).- Start-up protection (the controller only starts operating when the throttle is at 0. This prevents the motor from accidentally starting). If there is no RC signal, the vehicle stops.- Super-sensitive logarithmic control behavior (new evaluation system.- Two outputs for brake and reversing lights, each with a load of 1A, switch to ground.- 2,5 sqmm highly flexible connection cableDimensions 36 x 33 x 11 mmWeight 33 g

Available immediately, delivery time: 1-4 days

Product number: 9775

€ 66,95 *
%
1x standard servo CS-3 with JR connector. Dimensions: 38,5x19x32m
1x standard servo CS-3 with JR connector. Dimensions: 38,5x19x32mm. 4,8-6V voltage. Actuating torque at 4,8V: 31Ncm. Actuating time approx. 0,17sec./60°. Weight 39 g. Accessories: 2 rudder levers and screws.

Available immediately, delivery time: 1-4 days

Product number: 8851

€ 10,95 * € 11,49 * (4.7% saved)
1x Servonaut MFX mini-speed controller for adjusting and
1x Servonaut MFX mini speed controller for actuators and auxiliary drives or servo motors. Load capacity up to 10A. Frequency 16kHz. Voltage 6-12V (5-10 NiMH cells). Dimensions: 50x19x7mm. Integrated protection functions: -Overload protection -Overtemperature protection -Undervoltage protection -Diagnostic LED -Intelligent zero setting, no start-up protection -Can be used as universal servo electronics with adjustable control characteristics. -For servo operation, an additional potentiometer with 2kOhm or 5kOhm is required (NOT included!). No controller whistling (16KHz clocking) Instructions are available for downloading this article. Downloading is free! (except for your online costs). NEW ITEM - replaces the previous MFR!

Available immediately, delivery time: 1-4 days

Product number: 9181

€ 57,69 *
1x memory switch PS4aT with 4x 4A output 2x
1x memory switch PS4aT with 4x 4A output, 2x on/off function plus 2x tip-on function on 1 RC channel. Max voltage 20V 13x15x2,5mm, CTI product.

Available immediately, delivery time: 1-4 days

Product number: 3024

€ 18,00 *
1x 2-channel switch (2x Memory). The max. 2A / 20V
1x 2-channel switch (2x memory). 2 consumers can be switched on/off separately with 1 RC channel. Switching capacity per output max. 2A/ max. 20V. e.g. for lighting, headlights, fog horn, etc. Works with a free proportional channel or a 3-position switch on the transmitter. The 2-channel switch is particularly suitable for complex lighting with LEDs or bulbs, as 2 different functions can be operated independently of one another with just one channel. The RC transmitter does not need to be changed. Performance features: 2 separately and independently switchable switching functions with just one RC channel. Parallel operation on the servo is possible Negligible power consumption Possible switching capacity per switch 2 A / 0-20 Volt 2 powerful SMD-FETs Dimensions 26 mm x 11 mm x 5 mm Weight 9 g with cables Operation: In the following example, the module is connected to a channel with a vertical joystick. Channel 1: Move the joystick up and back to the 0 position. Channel 1 is switched on. Channel 2: Move the joystick down and back to the 0 position. Channel 2 is switched on. To switch off the respective channel, repeat the process!

Available immediately, delivery time: 1-4 days

Product number: 9778

€ 16,95 *
1x plastic ball joint, 5mm ball, for M3, ball bore
1x plastic ball joint, 5mm ball, for M3, ball bore 3mm, 27mm total length. Head diameter 7,3mm. 1 piece. Ball head height: 4,2mm.

Available immediately, delivery time: 1-4 days

Product number: 3796

€ 2,23 *
%
CARSON Reflex Stick Multi Pro LCD 2,4GHz Remote Control
CARSON Reflex Stick Multi Pro LCD 2,4GHz remote control with 14 channels. 14-channel transmitter, 14-channel receiver and manual. With 15 model memories. Reflex Stick Multi Pro LCD - Professional, modern and technically high-quality 14-channel remote control system with 15 model memories for universal use in many RC vehicles and ships. 14 channels can be controlled independently via 2 joysticks and 10 switches (4x buttons / 4x step switches / 2x rotary potentiometers), for example functions such as light / sound, horn, cable winch, support legs, water pump and fire monitor.The REFLEX STICK Multi Pro 14 Channel LCD System is fully compatible with the MFC 01/03 and DMD unit from TAMIYA. Scope of delivery:14 channel 2.4 GHz transmitter, 14 channel 2.4 GHz receiver and multilingual manual.Required accessories:4x Mignon AA cells. Mignon battery set article 9492Recommended accessories:500503060 Reflex 6 / 14Ch Switch 2 (2x2.5A, max. 16V)500503061 Reflex 6 / 14Ch Switch 4 (4x2.5A, max. 16V)500503062 Reflex Switch 2/4 power distributor500606073 Plug-in charger (item 10723)Transmitter charging cable: item 9673500501544 Receiver500609042 Mignon battery set (AA)Technical data:- Operating voltage transmitter 4,8 - 6 V (4 AA cells)- 2.4G FHSS system (Frequency HoppingSpread Spectrum)- 2.4G servo reverse (reversal of the direction of rotation) and trim function for channels- 4x buttons ON/OFF/ON, 4x switches ON/OFF/ON, 2x rotary potentiometers- Power supply for the receiver 4,8 - 6 V- Plug system Graupner J/R- Dual Rate channel 1-4 (servo travel limitation)- EPA channel 1-4 (servo travel limitation)- ABS function channel 1-4 (Stutter brake)- EXP function channel 1-4 (exponential)Technical details:- 14 controllable channels- 15 model memories- Includes charging socket- 100% compatible with TAMIYA MFC 01/03 and DMD unit- Blue illuminated LC displayIt is not possible to bind several receivers at the same time with this system.Receivers that can be used with this system:Article 11259, 4-channel receiverArticle 12422, 4-channel receiver, waterproofArticle 12421, 5-channel receiverArticle 12420, 5-channel receiver, waterproof

Available immediately, delivery time: 1-4 days

Product number: 10326

€ 145,00 * € 160,00 * (9.38% saved)
Single-cell battery Mignon Eneloop 2000mAh without soldering tag
Single cell rechargeable battery Mignon Eneloop 2000mAh without soldering tag, NiMH, HR-3U, Mignon size. 1 piece. Single cell rechargeable battery Mignon Eneloop 2000mAh without soldering tag, NiMH, HR-3U, Mignon size. 1 piece.

Ready to ship in 15 days, delivery time 1-4 days

Product number: 4399

€ 4,22 *
1x throttle AS-12 / 6RW Easy with cables. 100% back /
1x AS-12/6RW Easy speed controller with cables. 100% forward, 100% reverse. Max. 6A. Without BEC. 18kHz clocking! 6-15V input voltage. 5-12 cells NiMH or 2-3 LiPos. Dimensions: 20x17x5mm. 6gr. Version without cruise control! Max. current: 6A (10A short). Failsafe, no LiPo monitoring. Intelligent soft polarity reversal. Performance features: - 5-12 cells / 2-3 LiPos / 12 Volt lead - 6 A continuous, 10 A short-term - Full HF 18 kHz output stage over the entire control range. NO motor whistling and extremely sensitive control. - Motor-friendly polarity reversal thanks to speed-dependent polarity reversal time. Speed ​​range is immediately reversed (at high speeds the controller brakes the motor gently so that the battery and motor are protected from high current peaks.) - perfect failsafe (receiver signal is constantly checked) LED shows when the reception signal is lost. - Motor beep acknowledgement (for programming and for the OK message when connecting the battery). - Start-up protection (the controller only starts operating when the throttle stick is at 0. This prevents the motor from starting accidentally). If there is no RC signal, the vehicle stops. - super-sensitive logarithmic control behavior (new evaluation system. - 2,5 sqmm highly flexible connection cable Dimensions 20 x 17 x 5 mm Weight 6 g

Available immediately, delivery time: 1-4 days

Product number: 9867

€ 24,94 *
Speed ​​controller 4HF potentiometer. This controller is a Stro
Speed ​​controller 4HF potentiometer. This speed controller is a current measuring controller. With BEC (only for receiver supply). 17x17x6mm, CTI product. The 4HF potentiometer measures the current while the motor is running with a measuring resistor. If the current is higher than the maximum current set on the potentiometer, the software switches the motor off and indicates this with a red LED for control purposes. This protects the mechanics, motor and electronics in the event of overload or blocking operation. The motor can only start again after the transmitter stops the motor or steers it in the other direction.Technical data: Maximum driving voltage: 15V Dimensions: 17x17x6mm Battery and motor connection: 0,25qmm silicone Zero point: fixed at 1,5 microseconds Forward/backward: continuously variable up to maximum speed Areas of application:The HF4 potentiometer can be used universally for all applications where limit switches are not required.Examples: electric cylinders spindle drives loading ramps extendable vehicle supports extendable landing wheels and frames

Available immediately, delivery time: 1-4 days

Product number: 12324

€ 36,00 *
%
Servo HS-40 (Hitec). Analog nano servo 8,6mm wide
1 Servo HS-40 (Hitec). Analogue nano servo. Dimensions: 20x8,6x17mm. 4,8gr. Nylon gear. 6 / 7,6Ncm. 0,12s / 60 °. Uni / JR plug. Power is supplied with 4 different servo arms.

Available immediately, delivery time: 1-4 days

Product number: 8845

€ 12,50 * € 13,90 * (10.07% saved)
Servo patch cable 30 cm
1x servo patch cable 30 cm. Both sides JR servo connector. 0,14qmm. BEIER-Electronic Accessories.

Available immediately, delivery time: 1-4 days

Product number: 9812

€ 2,50 *
1x mini speaker Visaton 8 Ohm for 12V operation. 50 x
1x Visaton 8 Ohm mini speaker for 12V operation. 50 x 50mm. Depth 22mm. Nominal load capacity 4W. Music load capacity 10W. Dimensions approx. 50x50x25,5mm. Optionally available (not included): Matching speaker box: Item 9336, 8908 (for high roof), 12893. 5cm broadband speaker with square basket, soft surround and light special membrane. Balanced frequency response from 250Hz and lively high frequency reproduction with good omnidirectional behavior.

Available immediately, delivery time: 1-4 days

Product number: 7028

€ 14,90 *
Flat speaker 8 Ohm / 5W. For 12V operation. 90x40x14mm
1x flat speaker 8 Ohm/5W. For 12V operation. 90x40mm. Depth 14mm. For SMT, SMX and SM7 at 12V and SM3 at 7,2V. Loud89. Dimensions approx. 90x40x14mm. Loudspeaker boxes (not included) are available for this: Item 10826 or 11283 (for high roof) or 10828 (for AROCS high roof).

Available immediately, delivery time: 1-4 days

Product number: 9854

€ 13,70 *
%
1x Beier Sound module USM-RC-2 with DVD and manual
1x Beier sound module USM-RC-2 WITH DVD. Individually programmable sound, light and movement module. Over 140 finished sound projects. Comes with DVD and instructions. The sound module was specially developed for RC model making in order to create authentic and speed-dependent sounds, extensive lighting options and additional servo movements. Functional scope: -Individually programmable sound, light and movement module -Over 140 finished sound projects with preset and customizable sounds and noises -Use of your own noises, sounds and songs possible -Speed-dependent motor and movement sounds -Optimal sound thanks to powerful amplifier -12 outputs for switching LEDs, lamps, relays etc. -Freely adjustable light sequences, e.g. for an all-round light-2 programmable servo outputs-Easy updating of the sound teacher and the firmware-Easy transfer of all settings via micro SD card The USM-RC-2 sound module is characterized by its high adaptability. All settings are saved on a micro SD card and can therefore be easily changed. All you need is a reader and the "Sound Teacher" software. There are 3 different operating modes: - Digital operation (connection to the receiver) The connection is made using a servo patch cable directly to the receiver and parallel to the speed controller. - Analogue operation (connection directly to the motor) - Mixed operation (combination of digital and analogue operation) These modes are used for speed controllers with special functions, such as cruise control. The speed of the model is measured directly from the motor. The functions can be controlled in various ways. The remote control is assigned using the sound teacher. Sound functions: - Driving and engine sounds for two motors (speed-dependent) - Additional sounds (horns, hydraulic and compressed air noises, etc.) - Random sounds (chain squeaking, animal and ambient noises) Detailed: - Starting noises (cold/warm start) - Stopping noises - Starting noises - Stopping noises - Standing noises - Braking noises - Reversing noises Only up to 2 loudspeakers need to be connected to the sound module. Light functions: The sound module offers 12 switching outputs. The individual outputs can be configured in the Sound Teacher. This enables functions such as frequent flashing, flickering or on/off control. Movement functions: The USM-RC-2 sound module also offers 2 outputs for connecting servos. Technical data: - Supply voltage: 5-14V DC - Quiescent current: approx. 90mA operation: (sound only) max. 3A, (sound and switching outputs) max. 6A-Switching inputs: 5-Switching outputs: 12-Proportional inputs: 4-Proportional outputs: 2 servo outputs-Recommended speakers: 4-8 Ohm-Volume adjustment: Via external potentiometer or remote control-Supported sound data: WAV format 8/16 bit mono/stereo, 22/44kHz-Sound output: 16 bit, mono, 44kHz-Weight: 25g-Dimensions: 66x44x17 mmScope of delivery:-Sound module USM-RC-2-Micro SD card (4GB) + adapter (item 9818)-2 pieces connection cable for speakers (25cm) (item 9814)-2 pieces servo patch cable (30cm) for connection to a receiver, item 9812-Ribbon cable (40cm) for connecting the switching outputs (item 9815)-Fuse holder + fuse 4A (item 9817)-DVD-ROM with software (sound teacher) and sounds-Operating instructions (manual, German)Sounds are available for the following vehicles:-Car - Ford F-350 (V8)-Car - Landrover Discovery TD-Car - Mercedes 320 CDI_1-Car - Mercedes 320 CDI_2-Car - Mercedes C63 AMG-Car - Mercedes G (diesel)-Car - Mercedes Sprinter-Car - V8-Car - VW Bus-Car - VW Golf GTI-Car - VW Beetle-Excavator - Liebherr-Excavator - Volvo-Airplane - Focke Wulf 190-Airplane - Me 109 G10-Airplane - Wright radial engine helicopter - Huey helicopter - Rescue helicopter dump truck - Volvo A25C crawler loader - Caterpillar locomotive - Climax locomotive - Steam locomotive - Steam locomotive_1 locomotive - Diesel locomotive - Electric locomotive - GP38 motorcycle - Harley Davidson tank - Elephant tank - Gepard tank - Gepard_1 tank - Jagdpanther tank - Jagdpanther_1 tank - KV-1 tank - Kanonenjagdpanzer tank - King Tiger tank - King Tiger_1 tank - Leopard 1 tank - Leopard 1_1 tank - Leopard 2 tank - Leopard 2A6 tank - M1 tank - M26 tank - M41 Walker Bulldog tank - MARS tank - Panther tank - Panther G tank - Panther G_1 tank - Panther_1 tank - Panzer III tank - Panzer III_1 tank - Panzer IV tank - Piranha IIIH tank - Sd.Kfz. 7-Tank - Sherman Tank - T-34 Tank - T-55 Tank - Tiger Tank - Tiger_1 Tank - Tiger_2 Tank - Tiger_3 Snowcat - PB300 Snowcat - PB600 Snowcat - PB600_2 Snowcat - Prinoth Beast Wheel Loader - Liebherr Wheel Loader - Liebherr L586 Crawler - DET250 Crawler - Liebherr PR734 Crawler - T100 Ship - Barge Ship - Steamship Ship - Steamship SS

No longer available

Product number: 9794

€ 159,98 * € 169,00 * (5.34% saved)
Racing battery pack with SUB-C cells, 7,2V 6 cells, 5300mAh
1x racing battery pack with SUB-C cells, 7,2V 6 cells, 5300mAh with Tamiya plug. SUB-C cells. Dimensions approx 137x47x25mm. about 450 gr., NiMH, construction L2x3. With silicone strands!

Available immediately, delivery time: 1-4 days

Product number: 11028

€ 42,00 *
Plastic ball joint, 6mm ball, for M3 ball bore 3mm,
Plastic ball joint, 6mm ball, for M3 ball bore 3mm, 27mm total length, head diameter 9,5mm with hexagon. 1 piece.

Available immediately, delivery time: 1-4 days

Product number: 3795

€ 2,20 *
1x 2 channel switch (2x 10A) / 2 relay. 2 consumers could
1x 2-channel switch (2x 10A) / 2 relays. 2 consumers can be switched on/off separately with 1 RC channel. Switching capacity per output max. 10A each/ max. 40V. e.g. for lighting, headlights, fog horn, etc. Works with a free proportional channel or a 3-position switch on the transmitter. The 2-channel switch is particularly suitable for complex lighting with LEDs or bulbs, as 2 different functions can be switched independently of each other with just one channel. The RC transmitter does not need to be changed. Features: 2x separate SWITCH function with just one RC channel Switchable memory function for each function can be switched on via DIP. Parallel operation on the servo possibleNegligible power consumptionPossible switching capacity per switch 10A / 0-40 Volt2 relay levels with changeover contactsScrew connectionsLED function controlOperating voltage: 4,8-6VDimensions 40mm x 34mm x 21mmWeight 40g with servo cableOperation:In the following example, the module is connected to a channel withvertical control stick.Channel 1: Move the control stick up and hold itChannel 1 is switched on. (Touch function) Channel 2: Move the control stick down and hold itChannel 2 is switched on. (Touch function)To switch off the respective channel, move the control stick to the neutral position.When the MEMORY function is switched on, the channel remains switched on until the control stick is AGAIN moved to the same position.There is a practical holder for this module: Article 11956.

Available immediately, delivery time: 1-4 days

Product number: 11250

€ 20,94 *
Tip
1x Servonaut M24, speed controller with lighting system for trucks
Servonaut M24 speed controller with lighting system for trucks and functional models/vehicles. Speed ​​controller for 7,2 to 12V and 20A/5 min. at 16 or 32 kHz clock frequency, BEC 5,3V/4A, lighting system with 6 switching outputs each 700mA, including instructions, dimensions approx. 43x13x80mm. Equally suitable for conventional motors and bell-armature motors. Instructions are available for downloading for this article. Downloading is free! (except for your online costs).

Available immediately, delivery time: 1-4 days

Product number: 9766

€ 198,99 *
%
Battery Pack racing with 5000er cells F5x2 12V 10 cells AMP
1x battery racing pack with 5000 cells, 12V 10 cells, SUB-C, with AMP socket, approx. 16cm strands 1,5qmm, approx. 715g, F5x2, 115x46x44mm, NiMH cells. X-Cell cells.

Available immediately, delivery time: 1-4 days

Product number: 9966

€ 79,00 * € 94,90 * (16.75% saved)
X-BEC 5,7-35V input voltage, output 5,5V until max. 8A
X-BEC 5,7-35V input voltage, 5,5V output, up to max. 8A possible, 3A continuous current. CTI product.

Available immediately, delivery time: 1-4 days

Product number: 5112

€ 10,00 *
1x Servonaut S10 speed controller for small trucks and...
1x Servonaut S10 speed controller for small trucks and functional models/vehicles. Speed ​​controller for 7,2 to 12V and 10A/5min at 16 kHz clock frequency. BEC 5V/1A. 2 switching outputs, 20mA each for brake light and reversing light. Incl. instructions, dimensions approx. 55x19x7mm. For small functional models. Integrated protective functions: - Overload protection - Overtemperature protection - Undervoltage protection Also suitable for bell-shaped armature motors! Seamless EMF brake, no loss of control when driving downhill. Delay-free changeover forwards/backwards. BEC: 5V/1A receiver supply. Diagnostic LEDs. Undervoltage shutdown for 6 or 10 cells NiMH and 2 or 3 cells LiPo. Automatic zero setting with start-up protection. Instructions are available for downloading this article. Downloading is free! (except your online costs).NEW article - improved follow-up article to the MFR!

Available immediately, delivery time: 1-4 days

Product number: 9192

€ 62,50 *
Volume potentiometer
1x volume potentiometer. For BEIER electronic modules. To adjust the volume. Wire length: 20cm. Resistance 100 kOhm. For SFR-1, USM-RC-2, USM-RC-3, USM-xx.
1

End of life - article no longer available!

Product number: 9813

€ 4,95 *
%
1x CS-9 MG power servo with JR connector. Dimensions: 40x20x38mm
1x power servo CS-9 MG with JR connector. Dimensions: 40x20x38mm. 4,8-6V voltage. Actuating torque at 4,8V: 85Ncm. Actuating time approx. 0,1sec./60°. Weight 50 g. Accessories: 2 rudder levers and screws. This powerful servo is equipped with ball bearings and metal gears. It is also splash-proof and is therefore ideal as a steering servo in vehicles that sometimes move in damp environments!

Available immediately, delivery time: 1-4 days

Product number: 7939

€ 27,99 * € 29,99 * (6.67% saved)
1 horn for function models. Realist- ischer horn sound for
1 horn for functional models. Realistic horn sound for trucks or construction machines (e.g. excavators). Can be connected directly to the receiver output. Approx. 15x17mm, with M5 thread. Servo cable JR. Electronic horn with the sound of a truck horn. It makes sense to control it via a BUTTON on the transmitter! But of course any other control device (joystick, slider, etc.) can also be used for control. The power supply comes directly from the receiver no additional power supply necessary!

Available immediately, delivery time: 1-4 days

Product number: 7020

€ 35,00 *
1x Beier Sound module USM-RC-2 without DVD and Manual
1x Beier sound module USM-RC-2 Individually programmable sound, light and motion module. Over 140 finished sound projects. Delivery without DVD and instructions. The sound module was specially developed for RC model making to create authentic and speed-dependent sounds, extensive lighting options and additional servo movements. Functional scope: - Individually programmable sound, light and movement module - Over 140 ready-made sound projects with preset and customizable sounds and noises - Use of your own noises, sounds and songs possible - Speed-dependent motor and movement sounds - Optimal sound thanks to powerful amplifier - 12 outputs for switching LEDs, lamps, relays etc. - Freely adjustable light sequences, e.g. for an all-round light-2 programmable servo outputs-Easy updating of the sound teacher and the firmware-Easy transfer of all settings via micro SD card The USM-RC-2 sound module is characterized by its high adaptability. All settings are saved on a micro SD card and can therefore be easily changed. All you need is a reader and the "Sound Teacher" software. There are 3 different operating modes: - Digital mode (connection to the receiver) The connection is made using a servo patch cable directly to the receiver and parallel to the speed controller. - Analog mode (connection directly to the motor) - Mixed mode (combination of digital and analog mode) These modes are used for speed controllers with special functions, such as cruise control. The speed of the model is measured directly from the motor. The functions can be controlled in various ways. The remote control is assigned using the sound teacher. Sound functions: - Driving and engine sounds for two motors (speed-dependent) - Additional sounds (horns, hydraulic and compressed air noises, etc.) - Random sounds (chain squeaking, animal and ambient noises) Detailed: - Starting noises (cold/warm start) - Stopping noises - Starting noises - Stopping noises - Standing noises - Braking noises - Reversing noises Only up to 2 loudspeakers need to be connected to the sound module. Light functions: The sound module offers 12 switching outputs. The individual outputs can be configured in the Sound Teacher. This enables functions such as frequent flashing, flickering or on/off control. Movement functions: The USM-RC-2 sound module also offers 2 outputs for connecting servos. Technical data: - Supply voltage: 5-14V DC - Quiescent current: approx. 90mA operation: (sound only) max. 3A, (sound and switching outputs) max.

No longer available

Product number: 9795

€ 159,00 *
1x truck sound module SM7 with turbocharger 5 engines, 5
1x truck sound module SM7 with turbocharger 5 engines, 5 horns to choose from compressed air noise, siren, starting, stopping, gearshift noise. 7,2-12V. 7 watts. Successor to the SMX module! Sound module for truck models - successor to the proven SMX, significantly smallerDynamic turbocharger sound in a class of its own - even closer to the originalDriving situation-dependent engine sound with turbochargerIgnition, starter and shutdown noise, reversing warning tone5 truck horns, compressed air noises, siren5 engines: Actros V6, Scania V8, TGA in-line cylinder, DAF in-line 6-cylinder, Scania in-line 6-cylinderMulti-channel sound synthesisTurbocharger, compressed air, warning tone and switching noises can be set and adjusted separately in volume via Servonaut CARD (available as an accessory)Switching noises and warning tone with K15/30/40/60, reversing warning tone and brake-synchronized compressed air also available with M20+/M24 and S20/S22, function limited with speed controllers from other manufacturersStarter and horn can be operated optionally via switching inputs (Multiswitch) or a receiver channelSound module can be connected directly to an auxiliary motor or servo motor to simulate a power take-off noiseSmall separate volume control ideal for hidden installation on the modelFor 7,2V to 12V loudspeakers from 4 ohmsPower is supplied from the drive batteryWith battery plug (matching counterpart is BECB)Can be combined with SM+ for additional soundsOptional sound control SM-EQ available as an accessoryDimensions approx. 65 mm x 35 mm x 12 mmInstructions are available for download for this article. Downloading is free! (except for your online costs).Recommended loudspeakers with 7,2V supply voltage:Article 6049.Recommended loudspeakers with 12V supply voltage:Article 7028 or 9854.

Available immediately, delivery time: 1-4 days

Product number: 9066

€ 198,99 *
2,4GHz receiver with 9 servo channels, RX9. Partner capable.
2,4GHz receiver with 9 servo channels. RX9. Partner capable. Supports up to 2 multi-switch or multiprop modules. Servo outputs can be switched on/off remotely. Monitoring of driving voltage without accessories. This receiver of the latest generation is the successor to the previous Servonaut receivers R9 and R12 and is of course completely compatible. This receiver can be expanded to 12 or 16 channels and can be linked to TWO HS-12/HS-16 transmitters. This makes it easy to hand over a model. Receiver 55x28x9mm (without antenna). Antenna length 13cm.Note:The multiswitch/multiprop systems from Robbe and Graupner are supported by this receiver.Supply voltage: 4,8 - 7,4VBattery monitoring: for NiCd/NiMH 6 or 10 cells, LiPo/LiFePo 2 to 4 cells.Servonaut receiver of the latest generation (2018).To match this RX9 receiver, inexpensive channel extensions to 12 or 16 channels are offered.Extension by 3 channels (so 12 channels in total): article 11137Extension by 7 channels (so 16 channels in total): article 11138Extended settings possible via CARD (article 9096) or the HS-12 and HS-16 transmitters.

Available immediately, delivery time: 1-4 days

Product number: 11136

€ 137,99 *